Home › Drivetrain › R151 MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSMISSION UNIT › from 2016.01
RM3270E _52 Drivetrain _048960 R151 MANUAL TRANSMISSION / TRANSAXLE _0239357 MANUAL TRANSMISSION UNIT A

R151 MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION UNIT  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL STRAIGHT PIN AND RING PIN

NOTICE:

It is not necessary to remove a straight pin and ring pin unless it is being replaced.


a.
C325936C01
0.552,1.875 0.708,2.073 0.156,0.198 10 false A 2.833,0.094 2.99,0.292 0.156,0.198 10 false A 0.542,3.188 0.854,3.385 0.313,0.198 10 false *a 1.167,3.198 1.479,3.396 0.313,0.198 10 false *a 2.198,2.01 2.51,2.208 0.313,0.198 10 false *a 2.833,2 3.146,2.198 0.313,0.198 10 false *a
*a Protrusion Height


Using a plastic-faced hammer, tap 4 new ring pins into the intermediate plate.

Specified Condition:
Item Specified Condition
A 5.5 to 7.5 mm (0.217 to 0.295 in.)



b.
C325934C01
0.656,1.813 0.813,2.01 0.156,0.198 10 false A 2.76,0.104 2.917,0.302 0.156,0.198 10 false A 0.667,2.156 0.979,2.354 0.313,0.198 10 false *a 2.479,2.146 2.792,2.344 0.313,0.198 10 false *a
*a Protrusion Height


Using a plastic-faced hammer, tap 2 new straight pins into the transmission case.

Specified Condition:
Item Specified Condition
A 9.0 to 11.0 mm (0.355 to 0.433 in.)



Hide 2.INSTALL OUTPUT SHAFT

a.
C272938

Apply gear oil to the sliding part of the output shaft.


b.

Using a plastic-faced hammer, install the output shaft by tapping the intermediate plate.


Hide 33321B 3.INSTALL OUTPUT SHAFT BEARING SHAFT SNAP RING

a.
C272936

Using a snap ring expander, install a new output shaft bearing shaft snap ring to the output shaft.


Hide 5.INSTALL INPUT SHAFT

a.
C315172

Apply gear oil to the input shaft and No. 2 synchronizer ring, and install them to the output shaft.

NOTICE:
·

When installing the input shaft to the output shaft, align the protrusion of the No. 2 synchronizer ring with the cutout of the transmission clutch hub.

·

Check that the input shaft rotates slightly.




Hide 33421 6.INSTALL COUNTER GEAR

a.
C315171

Temporarily install the counter gear to the intermediate plate.


Hide 33411P 7.INSTALL COUNTER SHAFT REAR BEARING

a.
C272975E01
2.263,0.342 2.578,0.497 0.314,0.155 10 SST 2.67,0.44 2.842,0.44 2.842,0.44 2.474,1.33 false

Using SST and a hammer, tap in a new counter shaft rear bearing to the intermediate plate.

SST
09316-60011  (09316-00011)

HINT:

Install the counter shaft rear bearing while tapping the tip of the counter gear with a plastic-faced hammer so that the counter gear does not hit the side wall of the output shaft gear by being pushed forward.



b.

Using a snap ring expander, install the snap ring.


Hide 33402 8.INSTALL REVERSE IDLER GEAR SUB-ASSEMBLY

a.
C315170

Apply gear oil to each sliding part of the reverse idler gear sub-assembly and the reverse idler gear shaft, and install the reverse idler gear sub-assembly and reverse idler shaft to the intermediate plate.

NOTICE:

Install the reverse idler shaft with its groove facing the rear side, and install it from the rear side.



Hide 33151 9.INSTALL OUTPUT SHAFT REAR BEARING RETAINER

a.
C315169

Insert the output shaft rear bearing retainer into the groove of the reverse idler gear shaft and install it with the 4 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 33349C 10.INSTALL 5TH GEAR THRUST WASHER PIN

a.
C272930

Apply MP grease to the 5th gear thrust washer pin, and install it to the counter gear.


Hide 33349 11.INSTALL 5TH GEAR THRUST WASHER

a.
C272928

Apply gear oil to the 5th gear thrust washer, and install it to the counter gear.

NOTICE:

Install the 5th gear thrust washer so that its chamfer side faces forward.



Hide 33394B 12.INSTALL NO. 3 SYNCHROMESH SHIFTING KEY

a.

Apply gear oil to the sliding part of the No. 3 transmission hub sleeve, and install the hub sleeve to the counter 5th gear.

NOTICE:

Make sure that the No. 3 transmission hub sleeve and counter 5th gear are installed facing the correct direction.



b.
C248514C01
1.24,3.042 1.448,3.042 1.448,3.042 1.313,2.708 true 1.781,3.052 1.688,3.052 1.688,3.052 1.552,2.667 true 1.01,2.938 1.167,3.094 0.156,0.156 10 true *a 1.823,2.958 1.979,3.115 0.156,0.156 10 true *b
*a Cutout
*b Protrusion


Install the 2 No. 3 synchromesh shifting keys and No. 3 synchromesh shifting key spring to the counter 5th gear as shown in the illustration.

HINT:

When installing the No. 3 synchromesh shifting key spring, make sure the protrusion fits into the cutout.



c.
C247403

Using a snap ring expander, install a new shaft snap ring to the counter 5th gear.


Hide 33428B 13.INSTALL COUNTER 5TH GEAR BEARING

a.
C315168

Apply gear oil to the counter 5th gear bearing and install it to the countershaft 5th gear.


Hide 33428 14.INSTALL COUNTERSHAFT 5TH GEAR

a.
C272977

Apply gear oil to the countershaft 5th gear and No. 3 transmission hub sleeve, and install them to the countershaft.


Hide 33384A 15.INSTALL NO. 3 SYNCHRONIZER RING

a.
C272979

Apply gear oil to the No. 3 synchronizer ring, and install it to the countershaft 5th gear.

NOTICE:

Install the No. 3 synchronizer ring so that its protrusion fits between the 2 synchromesh shifting keys.



Hide 33318 16.INSTALL NO. 5 GEAR SPLINE PIECE

a.
C272981N01
2.223,0.175 2.518,0.324 0.295,0.149 10 SST 2.159,0.265 2.09,0.265 2.09,0.265 1.888,0.39 false

Using SST and a press, press in the No. 5 gear spline piece to the countershaft 5th gear.

SST
09316-60011  (09316-00011)

NOTICE:

Check that the gear rotates freely.



Hide 33421R 17.INSTALL COUNTER SHAFT REAR SNAP RING

a.
C330143C01
0.771,1.813 0.948,2 0.177,0.188 10 false *a
*a Thrust Clearance


Select a new snap ring so that the thrust clearance between the No. 5 gear spline piece and snap ring is within the specification.

Standard clearance:

0.10 mm (0.00393 in.) or less


Snap Ring Thickness:
Thickness
2.80 to 2.85 mm (0.111 to 0.112 in.)
2.85 to 2.90 mm (0.113 to 0.114 in.)
2.90 to 2.95 mm (0.115 to 0.116 in.)
2.95 to 3.00 mm (0.117 to 0.118 in.)
3.00 to 3.05 mm (0.119 to 0.120 in.)
3.05 to 3.10 mm (0.121 to 0.122 in.)
3.10 to 3.15 mm (0.123 to 0.124 in.)



b.
C272983

Using a brass bar and hammer, install the snap ring.


Hide 33428 18.INSPECT COUNTERSHAFT 5TH GEAR THRUST CLEARANCE

Hide 33428 19.INSPECT COUNTERSHAFT 5TH GEAR RADIAL CLEARANCE

Hide 33321A 20.INSTALL OUTPUT SHAFT REAR BEARING

a.
C272985

Using SST and a press, press in the spacer and a new output shaft rear bearing to the output shaft.

SST
09309-35010  


b.

Select a new shaft snap ring so that the thrust clearance between the output shaft rear bearing and shaft snap ring is within the specification.

Standard clearance:

0.10 mm (0.00393 in.) or less


Snap Ring Thickness:
Thickness Thickness
2.65 to 2.70 mm (0.105 to 0.106 in.) 3.10 to 3.15 mm (0.122 to 0.124 in.)
2.70 to 2.75 mm (0.107 to 0.108 in.) 3.15 to 3.20 mm (0.124 to 0.126 in.)
2.75 to 2.80 mm (0.109 to 0.110 in.) 3.20 to 3.25 mm (0.126 to 0.128 in.)
2.80 to 2.85 mm (0.111 to 0.112 in.) 3.25 to 3.30 mm (0.128 to 0.129 in.)
2.85 to 2.90 mm (0.113 to 0.114 in.) 3.30 to 3.35 mm (0.130 to 0.131 in.)
2.90 to 2.95 mm (0.115 to 0.116 in.) 3.35 to 3.40 mm (0.132 to 0.133 in.)
2.95 to 3.00 mm (0.117 to 0.118 in.) 3.40 to 3.45 mm (0.134 to 0.135 in.)
3.00 to 3.05 mm (0.119 to 0.120 in.) 3.45 to 3.50 mm (0.136 to 0.137 in.)
3.05 to 3.10 mm (0.121 to 0.122 in.) -



c.
C273479

Using a brass bar and hammer, install the output shaft bearing shaft snap ring.


Hide 33481 21.INSTALL SPEEDOMETER DRIVE GEAR

a.
C331376

Using snap ring pliers, install a new snap ring.


b.

Install the steel ball and speedmeter drive gear.


c.

Using snap ring pliers, install a new snap ring.


Hide 33228 22.INSTALL REVERSE SHIFT ARM BRACKET

a.
C291035

Install the reverse shift arm to the reverse shift arm bracket with a new snap ring.


b.
C291038C01
0.865,1.615 0.906,1.74 0.906,1.74 1.125,1.729 false 0.698,0.854 0.906,0.854 0.906,0.854 1.104,1.021 false 0.49,0.771 0.688,0.958 0.198,0.188 10 false *1 1.188,1.646 1.385,1.833 0.198,0.188 10 false *2
*1 Reverse Idler Gear
*2 Reverse Shift Arm


Insert the tip of the reverse shift arm into the reverse idler gear sub-assembly.


c.
C291034

Install the reverse shift arm bracket with the 2 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


d.
C291033

Install the torsion spring to the reverse shift arm bracket.

NOTICE:

Make sure that the torsion spring is securely installed to the reverse shift arm.



Hide 33211 23.INSTALL REVERSE SHIFT FORK

a.
C290803

Install the reverse shift fork to the reverse shift arm.


Hide 33241 24.INSTALL NO. 3 GEAR SHIFT FORK SHAFT

a.
C272922

Install the No. 3 gear shift fork to the No. 3 transmission hub sleeve and No. 3 gear shift fork shaft to the intermediate plate from the front side.


b.
C289009

Install the No. 1 shift interlock roller to the reverse shift fork.


c.
C288251

Using a brass bar and hammer, install a new shift fork shaft snap ring to the No. 3 gear shift fork shaft.


d.
C272920

Using a 5 mm pin punch and hammer, install a new shift fork set slotted spring pin to the No. 3 gear shift fork.


Hide 33242 25.INSTALL NO. 1 GEAR SHIFT FORK SHAFT

a.
C315166

Install the No. 1 shift interlock roller to the intermediate plate.


b.
C288249

Install the No. 1 gear shift fork to the reverse gear.


c.
C288248

Install the No. 1 gear shift fork shaft to the intermediate plate from the rear side.


d.
C288247

Install a new bolt to the No. 1 gear shift fork shaft.

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)


e.
C288252

Using a brass bar and hammer, install a new shift fork shaft snap ring to the No. 1 gear shift fork shaft.


Hide 33243A 26.INSTALL NO. 2 GEAR SHIFT FORK SHAFT

a.
C315165C01
0.76,0.271 1.333,0.271 false 0.792,0.594 1.365,0.594 false 0.594,0.51 0.802,0.719 0.208,0.208 10 false *2 0.563,0.208 0.771,0.417 0.208,0.208 10 false *1
*1 No. 1 Shift Interlock Roller
*2 Shift Interlock Pin


Install the shift interlock pin and No. 1 shift interlock roller to the intermediate plate.


b.
C288245

Install the No. 2 gear shift fork to the No. 2 transmission hub sleeve.


c.
C288244

Apply gear oil to the No. 2 gear shift fork shaft, and install the No. 2 gear shift fork shaft to the intermediate plate from the rear side.


d.
C288243

Install a new bolt to the No. 2 gear shift fork.

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)


e.
C288253

Using a brass bar and hammer, install a new shift fork shaft snap ring to the No. 2 gear shift fork shaft.


Hide 27.INSTALL SHIFT DETENT BALL PLUG

a.
C288241

Install 2 new shift detent ball compression springs and 2 shift detent balls to the intermediate plate.


b.
C314573C03
1.531,2.188 1.844,2.385 0.313,0.198 10 false *b 0.573,2.188 0.885,2.385 0.313,0.198 10 false *a
*a for Type A
*b for Type B


Install 2 new shift detent ball plugs to the intermediate plate.

i.

for Type A:

Using a T40 ''TORX'' socket wrench, install 2 new shift detent ball plugs to the intermediate plate.

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)


ii.

for Type B

Using a 6 mm hexagon socket wrench, install 2 new shift detent ball plugs to the intermediate plate.

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)



c.
C315164

Install the shift detent ball and shift detent ball compression spring to the intermediate plate.


d.
C314572C03
1.625,2.208 1.938,2.406 0.313,0.198 10 false *b 0.594,2.219 0.906,2.417 0.313,0.198 10 false *a
*a for Type A
*b for Type B


Install new shift detent ball plug to the intermediate plate.

i.

for Type A:

Using a T40 ''TORX'' socket wrench, install a new shift detent ball plug to the intermediate plate.

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)


ii.

for Type B

Using a 6 mm hexagon socket wrench, install a new shift detent ball plug to the intermediate plate.

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)



Hide 33449B 28.INSTALL TRANSMISSION MAGNET

a.
C315163

Clean the transmission magnet, and install it to the intermediate plate.


Hide 33111 29.INSTALL MANUAL TRANSMISSION CASE

a.
C315189C01
2.417,0.385 2.917,0.385 true 3,0.323 3.313,0.521 0.313,0.198 10 false *a
*a Seal Packing


Apply seal packing to the manual transmission case as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent



b.
C315190

Using a plastic-faced hammer, tap the manual transmission case to attach it to the intermediate plate.


Hide 33411Q 30.INSTALL COUNTER GEAR FRONT BEARING SNAP RING

a.
C315161

Using a snap ring expander, install the counter gear front bearing snap ring to the manual transmission case.


Hide 33311G 31.INSTALL FRONT BEARING SHAFT SNAP RING

a.
C315160

Using a snap ring expander, install the front bearing shaft snap ring to the manual transmission case.


Hide 33131A 32.INSTALL TRANSMISSION FRONT BEARING RETAINER OIL SEAL

Hide 33131 33.INSTALL FRONT BEARING RETAINER

a.

Clean and degrease the contact surface of the front bearing retainer and manual transmission case.


b.

Clean and degrease the 8 bolts and the installation holes in the manual transmission case.


c.
C315154C01
2.229,0.844 2.708,0.844 false 2.823,0.75 3.135,0.948 0.313,0.198 10 false *a
*a Seal Packing


Apply seal packing to the front bearing retainer as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:
·

Assemble the parts within 10 minutes of application. Otherwise, the seal packing material must be removed and reapplied.

·

Apply seal packing in a continuous line (width 1.2 mm (0.0472 in.)) along the sealing surface of the manual transmission case




d.
C315191

Install the front bearing retainer to the manual transmission case with 8 new bolts.

Torque:
16.5 N*m (168 kgf*cm, 12 ft.*lbf)


e.

Check that the input shaft and output shaft rotate smoothly.


Hide 33103R 34.INSTALL MANUAL TRANSMISSION EXTENSION HOUSING OIL SEAL

a.
C325701N02
0.927,0.76 1.208,0.323 1.208,0.323 1.396,0.323 true 1.448,0.25 1.771,0.448 0.323,0.198 10 false SST

Using SST and a hammer, tap in a new manual transmission extension housing oil seal to the extension housing sub-assembly.

SST
09710-30050  
09950-70010  (09951-07100)

Standard depth:

-0.5 to 0.5 mm (-0.196 to 0.196 in.)


NOTICE:

Be careful not to damage the oil seal lip.



b.

Lightly apply MP grease to the lip of the manual transmission extension housing oil seal.


Hide 33280 35.INSTALL REVERSE RESTRICT PIN

a.
C315159

Install the reverse restrict pin to the extension housing sub-assembly.


b.
C338394

Using a 5 mm pin punch and hammer, tap in the slotted pin to the extension housing sub-assembly.


c.
C338395

Using a T40 ''TORX'' socket wrench, install a new plug to the transfer adapter sub-assembly.

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)


Hide 33124F 36.INSTALL NO. 1 EXTENSION HOUSING OIL RECEIVER PIPE

a.

Install the No. 1 extension housing oil receiver pipe with the bolt.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


Hide 33124G 37.INSTALL NO. 2 EXTENSION HOUSING OIL RECEIVER PIPE

a.
C315156

Install the No. 2 extension housing oil receiver pipe to the extension housing sub-assembly.


Hide 33146 38.INSTALL EXTENSION HOUSING DUST DEFLECTOR

a.
C325694N01
0.635,0.688 1.375,1.021 false 0.281,0.573 0.74,0.771 0.458,0.198 10 false SST

Using SST and a hammer, tap in the extension housing dust deflector.

SST
09513-36040  


Hide 33103 39.INSTALL EXTENSION HOUSING SUB-ASSEMBLY

a.
C315189C01
2.417,0.385 2.917,0.385 true 3,0.323 3.313,0.521 0.313,0.198 10 false *a
*a Seal Packing


Apply seal packing to the extension housing sub-assembly as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent



b.

Install the shift and select lever to the extension housing sub-assembly.


c.
G034242

Connect the shift and select lever to the fork shaft and install the shift lever housing.


d.

Align the shift and select lever with the extension housing sub-assembly installation hole and push into the extension housing sub-assembly.


e.
C292752

Install the extension housing sub-assembly to the manual transmission case with the 10 bolts.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


f.
C344402

Install a new bolt to the shift lever housing.

Torque:
33.3 N*m (340 kgf*cm, 25 ft.*lbf)


Hide 33506F 40.INSTALL FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY

a.

Install a new gasket and the floor shift control shift lever retainer sub-assembly.


b.
C344401

Install the 6 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 33280 41.INSTALL REVERSE RESTRICT PIN ASSEMBLY

a.
C344400C01
1.333,0.198 1.438,0.198 1.438,0.198 1.604,0.542 false 1.281,1.958 1.438,1.958 1.438,1.958 1.615,1.698 false 1.146,0.104 1.333,0.292 0.188,0.188 10 false *a 1.094,1.885 1.292,2.083 0.198,0.198 10 false *b
*a White
*b Green


Install the 2 reverse restrict pin assemblies.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 84210 42.INSTALL BACK-UP LIGHT SWITCH ASSEMBLY

Hide 31111 43.INSTALL CLUTCH HOUSING

a.

Clean the threads of the bolts and the manual transmission case with non-residue solvent.


b.
C332848C02
1.177,1.281 0.573,1.104 0.573,1.104 1.156,0.969 true 0.385,1.021 0.573,1.219 0.188,0.198 10 false *a 0.771,1.365 0.906,1.542 0.135,0.177 10 true A 0.74,0.708 0.875,0.885 0.135,0.177 10 true A
*a Precoated Bolt


Install the clutch housing to the manual transmission case with the 7 bolts.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


c.

Install 2 new bolts (labeled A).

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


Hide 31236B 44.INSTALL RELEASE FORK SUPPORT

Hide 31230 45.INSTALL CLUTCH RELEASE BEARING ASSEMBLY

Hide 31126 46.INSTALL CLUTCH RELEASE FORK BOOT

Hide 33104 47.INSTALL DRAIN PLUG SUB-ASSEMBLY

a.
C315153

Install a new gasket and the drain plug sub-assembly to the manual transmission case.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 33101A 48.INSTALL MANUAL TRANSMISSION FILLER PLUG

a.
C315152

Install a new gasket and the manual transmission filler plug to the manual transmission case.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)