Home › Drivetrain › R151 MANUAL TRANSMISSION / TRANSAXLE › OUTPUT SHAFT › from 2016.01
RM3270E _52 Drivetrain _048960 R151 MANUAL TRANSMISSION / TRANSAXLE _0239359 OUTPUT SHAFT A

R151 MANUAL TRANSMISSION / TRANSAXLE  OUTPUT SHAFT  DISASSEMBLY  


PROCEDURE

Hide 1.INSPECT 1ST GEAR THRUST CLEARANCE

Hide 2.INSPECT 2ND GEAR THRUST CLEARANCE

Hide 3.INSPECT 3RD GEAR THRUST CLEARANCE

Hide 4.INSPECT 1ST GEAR RADIAL CLEARANCE

Hide 5.INSPECT 2ND GEAR RADIAL CLEARANCE

Hide 6.INSPECT 3RD GEAR RADIAL CLEARANCE

Hide 33335 7.REMOVE 1ST GEAR

a.
C315197N01
2.271,1.25 2.531,0.667 2.531,0.667 2.813,0.667 false 2.906,0.573 3.219,0.813 0.313,0.24 10 false SST

Using SST and a press, pull off the 5th gear, output shaft center bearing, 1st gear thrust washer and 1st gear from the output shaft.

SST
09950-00020  


Hide 33037B 8.REMOVE NO. 1 SYNCHRONIZER RING SET (FOR 1ST GEAR)

a.

Remove the No. 1 synchronizer ring set (for 1st gear) from the output shaft.


Hide 33348A 9.REMOVE 1ST GEAR THRUST WASHER PIN

a.

Remove the 1st gear thrust washer pin from the output shaft.


Hide 33335C 10.REMOVE 1ST GEAR NEEDLE ROLLER BEARING

a.

Remove the 1st gear needle roller bearing from the output shaft.


Hide 33335B 11.REMOVE 1ST GEAR BEARING SPACER

a.

Remove the 1st gear bearing spacer from the output shaft.


Hide 33321C 12.REMOVE BEARING SHAFT SNAP RING

a.
C315198

Using 2 screwdrivers and a hammer, remove the bearing shaft snap ring from the output shaft.

NOTICE:

Use a cloth to prevent the bearing shaft snap ring from flying off.



Hide 33332 13.REMOVE 2ND GEAR

a.
C315199N01
1.198,1.063 0.938,0.438 0.938,0.438 0.698,0.438 false 0.323,0.333 0.781,0.531 0.458,0.198 10 false SST

Using SST and a press, pull out the No. 1 transmission clutch hub together with the reverse gear, No. 1 synchronizer ring set (for 2nd gear) and 2nd gear from the output shaft.

SST
09950-00020  


Hide 33332B 14.REMOVE 2ND GEAR NEEDLE ROLLER BEARING

a.

Remove the 2nd gear needle roller bearing from the output shaft.


Hide 33331 15.REMOVE REVERSE GEAR

a.
C315200

Remove the reverse gear, 3 No. 1 synchromesh shifting keys and 3 No. 1 synchromesh shifting key springs.

NOTICE:

Use a cloth to prevent the shifting key and the shifting key springs from popping out.



Hide 33321D 16.REMOVE CLUTCH HUB SET SHAFT SNAP RING

a.

Using a snap ring expander, remove the clutch hub set shaft snap ring from the output shaft.


Hide 33333 17.REMOVE 3RD GEAR

a.
C315201N01
0.573,0.365 0.813,0.365 0.813,0.365 1.063,0.927 false 0.188,0.271 0.542,0.479 0.354,0.208 10 false SST

Using SST and a press, pull out the No. 2 transmission clutch hub together with the No. 2 transmission hub sleeve, No. 2 synchronizer ring and 3rd gear from the output shaft.

SST
09950-00020  


Hide 33333A 18.REMOVE 3RD GEAR NEEDLE ROLLER BEARING

a.

Remove the 3rd gear needle roller bearing from the output shaft.


Hide 33364 19.REMOVE NO. 2 TRANSMISSION HUB SLEEVE

a.

Remove the No. 2 transmission hub sleeve, 3 No. 2 synchromesh shifting key springs, and 3 No. 2 synchromesh shifting keys from the No. 2 clutch hub.

NOTICE:

Use a cloth to prevent the No. 2 shifting keys and No. 2 shifting key springs from popping out.



Hide 33348 24.INSPECT 1ST GEAR THRUST WASHER

Hide 33037B 25.INSPECT NO. 1 SYNCHRONIZER RING SET (FOR 1ST GEAR)

Hide 33037B 26.INSPECT NO. 1 SYNCHRONIZER RING SET (FOR 2ND GEAR)

Hide 33038E 27.INSPECT NO. 2 SYNCHRONIZER RING SET (FOR 3RD GEAR)

Hide 33361 29.INSPECT NO. 1 TRANSMISSION CLUTCH HUB

Hide 33364 30.INSPECT NO. 2 TRANSMISSION HUB SLEEVE

Hide 33362 31.INSPECT NO. 2 TRANSMISSION CLUTCH HUB