Home › Power Source / Network › 5L-E BATTERY / CHARGING › GENERATOR › from 2016.01
RM3270E _57 Power Source / Network _048967 5L-E BATTERY / CHARGING _0239363 GENERATOR A

5L-E BATTERY / CHARGING  GENERATOR  REASSEMBLY  


PROCEDURE

Hide 27330 1.INSTALL GENERATOR ROTOR ASSEMBLY

a.
A225703N01
1.083,0.333 1.167,0.333 1.167,0.333 1.5,0.667 true 0.771,0.25 1.229,0.448 0.458,0.198 10 false SST

Using SST and a press, press in the generator rotor assembly.

SST
09285-76010  


b.

Place a new washer on the generator rotor assembly.


Hide 27359 2.INSTALL GENERATOR RECTIFIER END FRAME

a.
A220286C02
0.75,0.25 0.833,0.25 0.833,0.25 1.615,0.833 true 0.51,0.156 0.823,0.313 0.313,0.156 10 false *a
*a 17 mm Socket Wrench


Using a 17 mm socket wrench and press, slowly press on the generator rectifier end frame.


b.

Install the core clip and 4 nuts.

Torque:
5.9 N*m (60 kgf*cm, 52 in.*lbf)


Hide 27357 3.INSTALL GENERATOR HOLDER WITH RECTIFIER

a.
A220287C02
0,0 0,0 false
V100135

Inside


Install the 4 rubber insulators to the lead wires.

NOTICE:

Be careful to install the rubber insulators in the correct direction.



b.
A220288C02
0,0 0,0 false
V100135

Push


While pushing down on the generator holder with rectifier, install it with the 4 screws.

Torque:
2.9 N*m (30 kgf*cm, 26 in.*lbf)


Hide 27700A 4.INSTALL GENERATOR REGULATOR ASSEMBLY

a.

Install the generator regulator assembly with the 3 screws.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)


Hide 27370 5.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.

Install the plate seal.


b.
A220289C02
0,0 0,0 false
V100135

Upper


Install the generator brush holder assembly with the 2 screws.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)


c.

Install the generator brush holder cover.


Hide 27039 6.INSTALL GENERATOR REAR END COVER

a.
A220290C02
2.417,1.75 2.5,1.75 2.5,1.75 2.74,1.042 true 2.219,1.667 2.531,1.823 0.313,0.156 10 false *1
*1 Rectifier Plate


Install the generator rear end cover and rectifier plate with the bolt and 3 nuts.

Torque:
for nut : 4.4 N*m (45 kgf*cm, 39 in.*lbf)
for bolt : 3.9 N*m (40 kgf*cm, 35 in.*lbf)


b.

Install the terminal insulator with the nut.

Torque:
4.1 N*m (42 kgf*cm, 36 in.*lbf)


Hide 29300 7.INSTALL VACUUM PUMP ASSEMBLY

a.

Align the matchmarks are install the vacuum pump assembly with the 4 bolts.

Torque:
7.8 N*m (80 kgf*cm, 69 in.*lbf)