Home › Drivetrain › AC60E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION FLUID › from 2016.01
RM3270E _52 Drivetrain _048959 AC60E AUTOMATIC TRANSMISSION / TRANSAXLE _0239364 AUTOMATIC TRANSMISSION FLUID N

AC60E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION FLUID  ADJUSTMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the automatic transmission fluid removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Automatic transmission fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly for 1GD-FTV:
(Click here)
for 2GD-FTV:
(Click here)
for 2TR-FE:
(Click here)
for 1GR-FE:
(Click here)

PROCEDURE

Hide 1. BEFORE FILLING TRANSMISSION

·

The AC60E automatic transmission assembly requires Toyota Genuine ATF WS.

·

If the entire automatic transmission assembly, automatic transmission oil pan sub-assembly, drain plug, transmission valve body assembly and/or torque converter assembly have/has been replaced, proceed to the Fill Transmission procedure.

·

If the extension housing rear oil seal has been replaced and/or an automatic transmission fluid leak has been replaced, proceed to the Adjust Fluid Temperature procedure.


Hide 2.FILL TRANSMISSION PAN WITH FLUID

a.

Lift the vehicle.

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure that the tilt angle from the front to rear of the vehicle is within +/-1°).



b.
C323947

Remove the refill plug and O-ring from the automatic transmission assembly.


c.
C323943

Using a 5 mm hexagon socket wrench, remove the overflow plug and gasket from the automatic transmission assembly.


d.
C323939C01
1.313,1.531 1.458,1.531 1.458,1.531 1.635,0.958 true 1.104,4.469 1.25,4.469 1.25,4.469 1.448,3.719 true 1.146,1.438 1.458,1.594 0.313,0.156 10 false *a 0.938,4.385 1.25,4.542 0.313,0.156 10 false *b
*a Refill Hole
*b Overflow Hole


Add automatic transmission fluid to the refill hole until it flows out of the overflow hole.

NOTICE:
·

Use Toyota Genuine ATF WS.

·

Be sure to add automatic transmission fluid slowly. If automatic transmission fluid is added quickly, the automatic transmission fluid may hit internal parts and bounce back, resulting in automatic transmission fluid coming out of the refill hole.




e.
C323941

Wait until the automatic transmission fluid flow slows and only drips come out.


f.
C323943

Using a 5 mm hexagon socket wrench, temporarily install the overflow plug and gasket to the automatic transmission assembly.

HINT:

Reuse the old gasket as the overflow plug will be removed again.



Hide 3.FILL TRANSMISSION

a.

Fill the automatic transmission assembly with the correct amount of automatic transmission fluid as listed in the table below.

Standard Capacity:
Performed Repair Engine Type Fill Amount
Automatic transmission fluid drain and refill 2TR-FE 3.1 liters (3.3 US qts, 2.7 Imp. qts)
1GD-FTV, 2GD-FTV, 1GR-FE 1.5 liters (1.6 US qts, 1.3 Imp. qts)
Removal and installation of the automatic transmission oil pan sub-assembly 2TR-FE 0.8 liters (0.8 US qts, 0.7 Imp. qts)
1GD-FTV, 2GD-FTV, 1GR-FE 2.4 liters (2.5 US qts, 2.1 Imp. qts)
Removal and installation of the transmission valve body assembly 2TR-FE 1.6 liters (1.7 US qts, 1.4 Imp. qts)
1GD-FTV, 2GD-FTV, 1GR-FE 3.1 liters (3.3 US qts, 2.7 Imp. qts)
Removal and installation of the torque converter assembly
(Including the oil drain)
2TR-FE 2.4 liters (2.5 US qts, 2.1 Imp. qts)
1GD-FTV, 2GD-FTV, 1GR-FE 4.2 liters (4.4 US qts, 3.7 Imp. qts)


HINT:

If the specified amount of automatic transmission fluid cannot be added, perform the following:


i.

Temporarily install the O-ring and refill plug to the automatic transmission assembly.

HINT:

Reuse the old O-ring as the refill plug will be removed again.



ii.

Lower the vehicle.


iii.

Start the engine.

NOTICE:

To reduce load, make sure that all electrical systems, such as the air conditioning, lighting system, electric fan and audio system, are off.



iv.

Slowly move the shift lever from P to D, then move the shift lever to P.

HINT:

Keep the shift lever in each position for approximately 3 seconds.



v.

Allow the engine to idle for 30 seconds to warm it up.


vi.

Turn the ignition switch off.


vii.

Remove the refill plug and O-ring from the automatic transmission assembly.


viii.

Fill the automatic transmission assembly with the correct amount of automatic transmission fluid as listed in the table above.


ix.

Temporarily install the O-ring and refill plug to the automatic transmission assembly.

HINT:

Reuse the old O-ring as the refill plug will be removed again.




Hide 4.ADJUST FLUID TEMPERATURE

NOTICE:

The automatic transmission fluid temperature can be confirmed by checking the D shift indicator on the combination meter or using the GTS. When not using the GTS, it is necessary to enter automatic transmission fluid temperature detection mode.


a.

When using the GTS:

HINT:

The actual ATF temperature can be checked on the Data List using the GTS.


i.

Connect the GTS to the DLC3 with the ignition switch off.


ii.

Turn the ignition switch to ON and turn the GTS on.

NOTICE:

To reduce load, make sure that all electrical systems, such as the air conditioning, lighting system, electric fan and audio system are off.



iii.

Enter the following item: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.

Powertrain > Engine and ECT > Active Test
Tester Display
Connect the TC and TE1
50004 234 13

iv.

Select the Active Test item: Connect the TC and TE1 / ON.


v.

Select the Data List item: A/T Oil Temperature 1.

Powertrain > Engine and ECT > Data List
Tester Display
A/T Oil Temperature 1
50003 234 406

vi.

Check the ATF temperature.

NOTICE:
·

If the automatic transmission fluid temperature is below 45°C (113°F), proceed to the next step. (Recommended ATF temperature: 35°C (95°F) or less)

·

If the automatic transmission fluid temperature is 45°C (113°F) or more, turn the ignition switch off and wait until the automatic transmission fluid temperature drops below 42°C (108°F).




vii.

Depress and hold the brake pedal.


viii.

Start the engine.

NOTICE:

To reduce load, make sure that all electrical systems, such as the air conditioning, lighting system, electric fan and audio system, are off.



ix.

Slowly move the shift lever from P to D, then move the shift lever to P.

HINT:

Keep the shift lever in each position for approximately 3 seconds.



x.
C344415

While observing the D shift indicator on the combination meter, move the shift lever back and forth between N and D at an interval of less than 1.5 seconds for 6 seconds or more.

NOTICE:

Do not pause for more than 1.5 seconds.


HINT:

Performing this operation will cause the vehicle to enter automatic transmission fluid temperature detection mode.



xi.

Check that the D shift indicator turns off for 2 seconds.

HINT:
·

When automatic transmission fluid temperature detection mode is activated, the D shift indicator on the combination meter will turn off for 2 seconds.

·

If the D shift indicator on the combination meter does not turn off for 2 seconds, return to the first step and perform the procedure again.




xii.

Move the shift lever from N to P.


xiii.

Release the brake pedal.


xiv.

Select the Active Test item: Connect the TC and TE1 / OFF.

NOTICE:

Make sure that terminals TC and TE1 are not connected. If the terminals are connected, the automatic transmission fluid level cannot be precisely adjusted due to fluctuations in engine speed.


HINT:
·

Disconnecting terminals TC and TE1 activates engine idle speed control mode.

·

Even after terminals TC and TE1 are disconnected, automatic transmission fluid temperature detection mode will be active until the ignition switch is turned off.





b.

When not using the GTS:

i.
C217398C07
1.615,0.906 2.052,0.396 false 1.792,1.479 2.042,1.823 false 2.073,1.823 2.292,1.969 0.219,0.146 10 false TC 2.073,0.24 2.302,0.385 0.229,0.146 10 false CG 0.083,0.083 0.271,0.26 0.188,0.177 10 false *a
*a Front view of DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3 with the ignition switch off.

SST
09843-18040  


ii.

Depress and hold the brake pedal.


iii.

Start the engine.

NOTICE:

To reduce load, make sure that all electrical systems, such as the air conditioning, lighting system, electric fan and audio system, are off.


HINT:

The indicator lights on the combination meter blink to indicate DTCs when terminals TC and CG are connected.



iv.

Slowly move the shift lever from P to D, then move the shift lever to P.

HINT:

Keep the shift lever in each position for approximately 3 seconds.



v.
C344415

While observing the D shift indicator on the combination meter, move the shift lever back and forth between N and D at an interval of less than 1.5 seconds for 6 seconds or more.

NOTICE:

Do not pause for more than 1.5 seconds.


HINT:

Performing this operation will cause the vehicle to enter automatic transmission fluid temperature detection mode.



vi.

Check that the D shift indicator turns off for 2 seconds.

HINT:
·

When automatic transmission fluid temperature detection mode is activated, the D shift indicator on the combination meter will turn off for 2 seconds.

·

If the D shift indicator on the combination meter does not turn off for 2 seconds, return to the first step and perform the procedure again.




vii.

Move the shift lever from N to P.


viii.

Release the brake pedal.


ix.
C217398C07
1.615,0.906 2.052,0.396 false 1.792,1.479 2.042,1.823 false 2.073,1.823 2.292,1.969 0.219,0.146 10 false TC 2.073,0.24 2.302,0.385 0.229,0.146 10 false CG 0.083,0.083 0.271,0.26 0.188,0.177 10 false *a
*a Front view of DLC3


Remove SST from terminals 13 (TC) and 4 (CG).

SST
09843-18040  

NOTICE:

Be sure that terminals TC and CG are not connected. If the terminals are connected, the automatic transmission fluid level cannot be precisely adjusted due to fluctuations in engine speed.


HINT:
·

Disconnecting terminals TC and CG activates the engine idle speed control mode.

·

Even after terminals TC and CG are disconnected, automatic transmission fluid temperature detection mode will be active until the ignition switch is turned off.





c.

Allow the engine to idle until the automatic transmission fluid temperature reaches 35 to 45°C (95 to 113°F).


d.

The D shift indicator will come on again when the automatic transmission fluid temperature reaches 35°C (95°F) and will blink when it exceeds 45°C (113°F).

HINT:

Adjust the automatic transmission fluid level when the D shift position indicator is illuminated.

1.

If the D shift position indicator is not illuminated, idle the engine to warm it up until the D shift position indicator illuminates.

2.

If the D shift position indicator is illuminated, immediately begin to adjust the automatic transmission fluid level.

3.

If the D shift position indicator is blinking, stop the engine to cool the automatic transmission fluid. Once the automatic transmission fluid temperature drops to the appropriate level, perform the automatic transmission fluid level adjustment procedure again.



D Shift Indicator
Below Automatic Transmission Fluid Level Adjustment Temperature
(35°C or less)
(95°F or less)
Automatic Transmission Fluid Level Adjustment Temperature
(35 to 45°C)
(95 to 113°F)
Above Automatic Transmission Fluid Level Adjustment Temperature
(45°C or more)
(113°F or more)
OFF ON Blinks


Hide 5.CHECK FLUID LEVEL

CAUTION:

Use caution while the engine is idling and the radiator fan is operating.


a.

Lift the vehicle.

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure that the tilt angle from the front to rear of the vehicle is within +/-1°).



b.
C323943

Using a 5 mm hexagon socket wrench, remove the overflow plug and gasket from the automatic transmission assembly.

CAUTION:

Be careful as the automatic transmission fluid coming out of the overflow hole is hot.



c.

Check the amount of automatic transmission fluid that comes out of the overflow hole.

·

If the amount of automatic transmission fluid that comes out of the overflow hole is large, proceed to step [*1].

·

If no automatic transmission fluid comes out of the overflow hole, proceed to step [*2].


NOTICE:

If only a small amount of automatic transmission fluid (approximately 5 cc) comes out of the overflow hole, then only automatic transmission fluid remaining in the No. 1 transmission oil filler tube has come out. This is not considered to be overflow.



d.
C323941

If the amount of automatic transmission fluid that comes out of the overflow hole is large, wait until the automatic transmission fluid flow slows and only drips come out. [*1]

HINT:

The automatic transmission fluid flow will not stop completely because the automatic transmission fluid continues to expand as its temperature increases.



e.
C323939C01
1.313,1.531 1.458,1.531 1.458,1.531 1.635,0.958 true 1.104,4.469 1.25,4.469 1.25,4.469 1.448,3.719 true 1.146,1.438 1.458,1.594 0.313,0.156 10 false *a 0.938,4.385 1.25,4.542 0.313,0.156 10 false *b
*a Refill Hole
*b Overflow Hole


If no automatic transmission fluid comes out of the overflow hole, remove the refill plug and O-ring. Then add automatic transmission fluid to the refill hole until it flows out of the overflow hole. Wait until the automatic transmission fluid flow slows and only drips come out. [*2]

NOTICE:
·

Use Toyota Genuine ATF WS.

·

Be sure to add automatic transmission fluid slowly. If automatic transmission fluid is added quickly, the automatic transmission fluid may hit internal parts and bounce back, resulting in automatic transmission fluid coming out of the refill hole.




f.
C323941

Wait until the automatic transmission fluid flow slows and only drips come out.

HINT:

The automatic transmission fluid flow will not stop completely because the automatic transmission fluid continues to expand as its temperature increases.



g.
C323943

Using a 5 mm hexagon socket wrench, install a new gasket and the overflow plug to the automatic transmission assembly.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


h.
C323947

Install a new O-ring and the refill plug to the automatic transmission assembly.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)


i.

Lower the vehicle.


j.

Turn the ignition switch off.

HINT:

Turning the ignition switch off exits automatic transmission fluid temperature detection mode.



k.

Disconnect the GTS from the DLC3 (when using the GTS).


Hide 6. AFTER FILLING TRANSMISSION

a.

Lift the vehicle.


b.

Clean each part.


c.

Check for automatic transmission fluid leaks.


d.

Lower the vehicle.