Home › Engine / Hybrid System › 5L-E ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _048946 5L-E ENGINE CONTROL _0236357 ECD SYSTEM C

5L-E ENGINE CONTROL  ECD SYSTEM  P0105  Manifold Absolute Pressure / Barometric Pressure Circuit  


DESCRIPTION

The manifold absolute pressure sensor generates voltage by the vacuum value as shown in the illustration. This voltage of the manifold absolute pressure sensor is one of the factors used to decide the injection volume and injection timing.

A006532E02
0.383,0.468 0.498,0.671 0.115,0.202 10 V 0.301,0.781 0.523,0.983 0.223,0.202 10 4.5 0.273,1.875 0.509,2.078 0.235,0.202 10 0.5 0.871,2.286 1.163,2.488 0.292,0.202 10 60.0 2.259,2.301 2.633,2.504 0.374,0.202 10 206.7 2.896,2.121 3.163,2.324 0.267,0.202 10 kPa 2.9,2.508 3.354,2.711 0.454,0.202 10 mmHg 2.882,2.854 3.327,3.057 0.445,0.202 10 (in.Hg) 2.24,2.664 2.652,3.032 0.412,0.368 10 1,550 (61.0) 0.957,2.671 1.35,3.039 0.393,0.368 10 450 (17.7) 1.279,3.073 2.077,3.275 0.797,0.202 10 Air Pressure 3.019,3.265 3.414,3.386 0.395,0.12

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0105 Manifold Absolute Pressure / Barometric Pressure Circuit Open or short in manifold absolute pressure sensor circuit for 2 seconds or more.
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM


Comes on DTC stored

WIRING DIAGRAM

A311403E01
1.708,1.01 2.021,1.208 0.313,0.198 10 false VC 1.677,1.615 1.99,1.813 0.313,0.198 10 false PIM 1.823,2.26 2.135,2.458 0.313,0.198 10 false E 4.99,0.875 5.51,1.073 0.521,0.198 10 false VCPM 4.99,1.531 5.302,1.729 0.313,0.198 10 false PIM 4.99,2.156 5.51,2.354 0.521,0.198 10 false EPIM 2.042,0.865 2.354,1.063 0.313,0.198 10 false 3 2.042,1.5 2.354,1.698 0.313,0.198 10 false 2 2.042,2.135 2.354,2.333 0.313,0.198 10 false 1 0.781,2.781 2.99,2.99 2.208,0.208 10 false Manifold Absolute Pressure Sensor 0.781,2.583 1.094,2.781 0.313,0.198 10 false C53 5.5,3.125 5.896,3.302 0.396,0.177 10 false C175 5.5,3.302 5.896,3.479 0.396,0.177 10 false ECM 6.021,0.74 6.333,0.938 0.313,0.198 10 false 5V 4.688,0.875 5,1.073 0.313,0.198 10 false 24 4.688,1.5 5,1.698 0.313,0.198 10 false 33 4.688,2.135 5,2.333 0.313,0.198 10 false 32

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (MAF)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAP.

Powertrain > Engine and ECT > Data List
Tester Display
MAP
50003 61 314

d.

Read the value.

OK:

The same as atmospheric pressure.


HINT:

Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather (high atmospheric pressure, low atmospheric pressure).



Intake Manifold Pressure (kPa) Malfunction
Approx. 0
·

Open in VC circuit

·

Short in PIM circuit


192 or more
·

Open in PIM circuit

·

Open in E2 circuit



Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTION OF VACUUM HOSE

NG

3.CHECK HARNESS AND CONNECTOR (ECM - MANIFOLD ABSOLUTE PRESSURE SENSOR)
2.CHECK CONNECTION OF VACUUM HOSE
a.

Check that the vacuum hose is securely connected and there are no leaks from the connection.

OK:

The vacuum hose is securely connected and there are no leaks from the connection.


Result:
Proceed to
OK
NG




OK

3.CHECK HARNESS AND CONNECTOR (ECM - MANIFOLD ABSOLUTE PRESSURE SENSOR)

NG

REPAIR OR REPLACE VACUUM HOSE

3.CHECK HARNESS AND CONNECTOR (ECM - MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C53-2 (PIM) - C175-33 (PIM) Always Below 1 Ω
C53-3 (VC) - C175-24 (VCPM) Always Below 1 Ω
C53-1 (E) - C175-32 (EPIM) Always Below 1 Ω
C53-2 (PIM) or C175-33 (PIM) - Body ground and other terminals Always 10 kΩ or higher
C53-3 (VC) or C175-24 (VCPM) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

4.INSPECT ECM (CHECK VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT ECM (CHECK VOLTAGE)
a.
A204467C46
0.677,1.135 1.042,1.385 0.365,0.25 1.24,1.75 1.49,1.292 true 2.177,1.729 1.948,1.292 true 0.167,0.208 0.479,0.406 0.313,0.198 10 false *a 0.729,1.177 1.052,1.375 0.323,0.198 10 false C53 1.177,1.75 1.479,2 0.302,0.25 10 false E 2.198,1.74 2.51,1.938 0.313,0.198 10 false VC
*a Front view of wire harness connector
(to Manifold Absolute Pressure Sensor)


Disconnect the manifold absolute pressure sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
C53-3 (VC) - C53-1 (E) Ignition switch ON 4.5 to 5.5 V


Result:
Proceed to
OK
NG




OK

5.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

5.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Replace the manifold absolute pressure sensor.


Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
6.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTC.

Powertrain > Engine and ECT > Clear DTCs
50002 61

d.

Turn the ignition switch to ON.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

f.

Check the DTC.

Result:
Display (DTC output) Proceed to
DTC P0105 is output again A
No DTC output B




A

B

END