Home › Engine / Hybrid System › 5L-E ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _048946 5L-E ENGINE CONTROL _0236357 ECD SYSTEM C

5L-E ENGINE CONTROL  ECD SYSTEM  P1121  Throttle / Pedal Position Sensor/Coolant Flow Control Valve Position Sensor Circuit Stuck  


DESCRIPTION

Refer to DTC P1120

Click hereEngine / Hybrid System>5L-E ENGINE CONTROL>ECD SYSTEM>P1120

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1121 Throttle / Pedal Position Sensor/Coolant Flow Control Valve Position Sensor Circuit Stuck
Condition 1
·

Either of the ECM sensors have completed learning and theelectric potential difference of VPA and VPA2 sensors hasbecome more than 1.2 V or less than 0.4 V.


Condition 2
·

One of the following continues more than 2.0 seconds.

1.

When the electrical potential difference of VPA and VPA2 sensors is not within the specified range.

2.

VPA2 is 4.9 V or higher.

3.

Accelerator idling criterion voltage of VPA and VPA2 is less than 0.04 V.



·

Open or short in accelerator pedal position sensor circuit

·

Accelerator pedal position sensor

·

ECM


Comes on DTC stored

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (ACCELERATOR POSITION)
a.
C129061C03
0.833,1.594 1.042,1.802 0.208,0.208 10 false *a 0.271,0.323 0.479,0.531 0.208,0.208 10 false *1 2.24,1.594 2.5,1.802 0.26,0.208 10 false *b
*1 Accelerator Pedal Assembly
*a Depressed
*b Released


Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.

Powertrain > Engine and ECT > Data List
Tester Display
Accel Sens. No.1 Volt %
Accel Sens. No.2 Volt %
50003 61 75,76

d.

Read the values.

OK:

Check that the value displayed on the GTS changes by repeatedly depressing and releasing the accelerator pedal.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (ECM - ACCELERATOR PEDAL POSITION SENSOR)
2.CHECK HARNESS AND CONNECTOR (ECM - ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the accelerator pedal position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A30-1 (VCP2) - G161-23 (VCP2) Always Below 1 Ω
A30-2 (EPA2) - G161-29 (EPA2) Always Below 1 Ω
A30-3 (VPA2) - G161-28 (VPA2) Always Below 1 Ω
A30-4 (VCPA) - G161-26 (VCPA) Always Below 1 Ω
A30-5 (EPA) - G161-27 (EPA) Always Below 1 Ω
A30-6 (VPA) - G161-20 (VPA) Always Below 1 Ω
A30-1 (VCP2) or G161-23 (VCP2) - Body ground and other terminals Always 10 kΩ or higher
A30-2 (EPA2) or G161-29 (EPA2) - Body ground and other terminals Always 10 kΩ or higher
A30-3 (VPA2) or G161-28 (VPA2) - Body ground and other terminals Always 10 kΩ or higher
A30-4 (VCPA) or G161-26 (VCPA) - Body ground and other terminals Always 10 kΩ or higher
A30-5 (EPA) or G161-27 (EPA) - Body ground and other terminals Always 10 kΩ or higher
A30-6 (VPA) or G161-20 (VPA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR