Throttle control motor is operated by the ECM and opens and closes the throttle valve.
The fully open position of the throttle valve is detected by the throttle open switch which is mounted on the venturi assembly.
If this DTC is stored, the ECM shuts down the power for the throttle control motor.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P1222 | Throttle Motor Circuit Range/Performance | Either condition is met (1 trip detection logic):
·
Open or short in throttle control motor circuit. ·
Open or short in throttle open switch circuit. |
·
Open or short in throttle control motor circuit ·
Throttle control motor (Venturi assembly) ·
Intake restrictor valve ·
Open or short in throttle open switch circuit ·
Throttle open switch (Venturi assembly) ·
ECM |
Comes on | DTC stored |
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| *a | Component without harness connected
(Throttle Open Switch) |
Disconnect the throttle open switch connector.
Remove the venturi assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | Below 1 Ω |
| 1 - 2 | Always | 10 kΩ or higher |
The throttle open switch is integrated with the venturi assembly. If the throttle open switch is replaced, the venturi assembly must be replaced in whole.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the throttle open switch connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C185-2 - C175-15 (THOP) | Always | Below 1 Ω |
| C185-1 - Body ground | Always | Below 1 Ω |
| C185-2 or C175-15 (THOP) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Throttle Control Motor) |
Disconnect the throttle control motor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C184-2 (+B1) - Body ground | Always | 11 to 14 V |
| C184-5 (+B2) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the throttle control motor.
Click hereEngine / Hybrid System>5L-E ENGINE CONTROL>DIESEL THROTTLE BODY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the throttle control motor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C184-6 (LU+A) - C174-17 (LU+A) | Always | Below 1 Ω |
| C184-4 (LU-A) - C174-16 (LU-A) | Always | Below 1 Ω |
| C184-3 (LU+B) - C174-15 (LU+B) | Always | Below 1 Ω |
| C184-1 (LU-B) - C174-14 (LU-B) | Always | Below 1 Ω |
| C184-6 (LU+A) or C174-17 (LU+A) - Body ground and other terminals | Always | 10 kΩ or higher |
| C184-4 (LU-A) or C174-16 (LU-A) - Body ground and other terminals | Always | 10 kΩ or higher |
| C184-3 (LU+B) or C174-15 (LU+B) - Body ground and other terminals | Always | 10 kΩ or higher |
| C184-1 (LU-B) or C174-14 (LU-B) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG