Home › Engine / Hybrid System › 5L-E ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _048946 5L-E ENGINE CONTROL _0236357 ECD SYSTEM C

5L-E ENGINE CONTROL  ECD SYSTEM  P1520  Stop Light Switch Circuit Malfunction  


DESCRIPTION

In this system, the signal of the stop light switch is used to judge whether the stop light system is abnormal or not.

The stop light switch has a duplex system (signals STP and ST1-) to recognize the abnormality when the signals of depressing and releasing the brake pedal are detected simultaneously.

HINT:

The normal signal conditions are as shown in the table below.

Signal Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1520 Stop Light Switch Circuit Malfunction Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic):
(a) Ignition switch is ON.
(b) Brake pedal is released.
(c) The STP signal is off when the ST1- signal is off.
·

Open or short in stop light switch signal circuit

·

Stop light switch assembly

·

ECM


- DTC stored

WIRING DIAGRAM

A379127E02
1.729,1.698 2.344,1.896 0.615,0.198 10 false G135 1.729,1.865 3.427,2.083 1.698,0.219 10 false Ignition Switch Assembly 1.771,1.219 2.385,1.417 0.615,0.198 10 false AM2 2.531,1.219 2.813,1.385 0.281,0.167 10 false IG2 0.438,1.479 1.573,1.885 1.135,0.406 10 false STRG LOCK/AM2 NO. 1 3.365,1.469 4.073,1.667 0.708,0.198 10 false IG2 NO. 3 3.438,2.542 4.146,2.74 0.708,0.198 10 false STOP 0.833,2.552 1.542,2.75 0.708,0.198 10 false ALT 0.458,3.094 1.167,3.292 0.708,0.198 10 false FL MAIN 0.604,3.823 1.271,4.052 0.667,0.229 10 false Battery 5.104,2.396 5.438,2.583 0.333,0.188 10 false L 4.427,3.365 5.552,3.75 1.125,0.385 10 false Stop Light Switch Assembly 4.438,3.177 4.771,3.365 0.333,0.188 10 false A64 4.469,2.396 4.802,2.583 0.333,0.188 10 false B 4.479,1.313 4.813,1.5 0.333,0.188 10 false B 5.094,1.313 5.427,1.5 0.333,0.188 10 false L 4.875,2.74 5.208,2.927 0.333,0.188 10 false GND 5.969,1.198 6.302,1.385 0.333,0.188 10 false ST1- 5.979,2.292 6.313,2.479 0.333,0.188 10 false STP 4.281,1.198 4.615,1.385 0.333,0.188 10 false 6 5.281,2.281 5.615,2.469 0.333,0.188 10 false 3 5.281,1.198 5.615,1.385 0.333,0.188 10 false 5 4.302,2.271 4.635,2.458 0.333,0.188 10 false 7 5.271,2.635 5.604,2.823 0.333,0.188 10 false 2 5.708,2.281 6.042,2.469 0.333,0.188 10 false 9 5.708,1.208 6.042,1.396 0.333,0.188 10 false 10 6.24,3.365 6.677,3.552 0.438,0.188 10 false G160 6.25,3.542 6.583,3.729 0.333,0.188 10 false ECM 2.854,1.208 3.188,1.396 0.333,0.188 10 false 3 1.594,1.198 1.927,1.385 0.333,0.188 10 false 4

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TERMINAL VOLTAGE)
a.
E270270C09
0.208,1.073 0.656,1.375 0.448,0.302 2.042,1.208 1.479,1.823 true 2.375,1.188 2.792,1.854 true 0.302,1.146 0.76,1.344 0.458,0.198 10 false A64 0.115,0.125 0.427,0.323 0.313,0.198 10 false *a 1.406,1.865 1.563,2.063 0.156,0.198 10 false B 2.781,1.896 2.938,2.094 0.156,0.198 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Turn the igntion switch to ON


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A64-6 (B) - Body ground Ignition switch ON 11 to 14 V
A64-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY,INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)
a.

Disconnect the stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in thetable below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK ECM (STP AND ST1- VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK ECM (STP AND ST1- VOLTAGE)
a.
A303106C11
1.938,2.531 2.354,2.792 0.417,0.26 1.813,3.938 2.188,3.177 true 2.615,3.906 2.26,3.177 true 0.167,0.083 0.479,0.281 0.313,0.198 10 false *a 1.771,0.083 2.083,0.281 0.313,0.198 10 false *b 0.25,2.219 0.563,2.417 0.313,0.198 10 false *c 1.979,2.573 2.354,2.771 0.375,0.198 10 false G160 2.375,3.948 2.979,4.198 0.604,0.25 10 false 9 (STP) 1.573,3.969 2.198,4.219 0.625,0.25 10 false 10 (ST1-)
*a Brake Pedal Depressed
*b Brake Pedal Released
*c Component with harness connected
(ECM)


Turn the ignition switch to ON


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Condition Specified Condition
G160-10 (ST1-) - Body ground Released 7.5 to 14 V
Depressed 0 to 1.5 V
G160-9 (STP) - Body ground Released 0 to 1.5 V
Depressed 7.5 to 14 V



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
a.

Disconnect the stop light switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-3 (L) - G160-9 (STP) Always Below 1 Ω
A64-5 (L) - G160-10 (ST1-) Always Below 1 Ω
A64-3 (L) or G160-9 (STP) - Body ground and other terminals Always 10 kΩ or higher
A64-5 (L) or G160-10(ST1-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR