Home › Engine / Hybrid System › 5L-E ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _048946 5L-E ENGINE CONTROL _0236357 ECD SYSTEM J

5L-E ENGINE CONTROL  ECD SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, the battery voltage is applied to terminal IGSW of the ECM. The ECM "MREL" output signal causes current to flow to the EFI relay coil, closing the contacts of the EFI relay and supplying power to terminal +B of the ECM.

WIRING DIAGRAM

A379173E03
1.021,0.563 2.604,0.76 1.583,0.198 10 false STRG LOCK/AM2 NO. 1 2.802,0.927 3.781,1.125 0.979,0.198 10 false Ignition Switch 2.802,0.771 3.781,0.969 0.979,0.198 10 false G135 2.823,0.479 3.208,0.656 0.385,0.177 10 false AM2 3.333,0.479 3.583,0.667 0.25,0.188 10 false IG2 2.656,0.25 2.844,0.427 0.188,0.177 10 false 4 3.646,0.25 3.833,0.427 0.188,0.177 10 false 3 0.75,2.188 1.573,2.385 0.823,0.198 10 false J/B-B 0.729,2.917 1.552,3.115 0.823,0.198 10 false FL MAIN 2.573,2.74 5,2.938 2.427,0.198 10 false Instrument Panel Junction Block 2.344,1.583 2.635,1.781 0.292,0.198 10 false 2B 2.354,2.094 2.646,2.302 0.292,0.208 10 false 2J 2.385,1.917 2.677,2.125 0.292,0.208 10 false 5 2.365,1.396 2.656,1.604 0.292,0.208 10 false 1 4.583,1.385 4.875,1.594 0.292,0.208 10 false 5 4.583,1.927 4.875,2.135 0.292,0.208 10 false 9 4.552,1.573 4.844,1.771 0.292,0.198 10 false 2G 4.552,2.104 4.844,2.302 0.292,0.198 10 false 2P 2.563,1.781 3.667,1.979 1.104,0.198 10 false EFI-MAIN NO. 1 3.438,2.427 4.542,2.625 1.104,0.198 10 false EFI-MAIN NO. 1 4.313,0.521 5.01,0.719 0.698,0.198 10 false IG2 NO. 1 5.573,0.354 5.99,0.531 0.417,0.177 10 false G161 5.563,1.573 5.979,1.75 0.417,0.177 10 false G161 5.563,2.104 5.979,2.281 0.417,0.177 10 false G161 5.573,3.115 5.99,3.292 0.417,0.177 10 false C174 6.01,0.365 6.708,0.563 0.698,0.198 10 false IGSW 6.01,1.573 6.708,1.771 0.698,0.198 10 false +B 6.01,2.104 6.708,2.302 0.698,0.198 10 false MREL 6,3.115 6.698,3.313 0.698,0.198 10 false E1 5.677,2.917 5.906,3.083 0.229,0.167 10 false 5 5.635,1.917 5.865,2.083 0.229,0.167 10 false 10 5.677,1.385 5.906,1.552 0.229,0.167 10 false 1 5.635,0.177 5.865,0.344 0.229,0.167 10 false 11 6.208,3.875 6.906,4.073 0.698,0.198 10 false ECM 0.844,3.771 1.667,3.969 0.823,0.198 10 false Battey

CAUTION / NOTICE / HINT

HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT ECM (+B VOLTAGE)
a.
A080463C85
0.552,0.198 0.969,0.458 0.417,0.26 2.51,0.208 2.938,0.469 0.427,0.26 0.667,0.792 0.417,1.5 true 2.979,0.792 2.99,1.531 true 0.594,0.25 0.958,0.448 0.365,0.198 10 false C174 2.563,0.26 2.958,0.458 0.396,0.198 10 false G161 0.26,1.542 0.708,1.74 0.448,0.198 10 false 5 (E1) 2.854,1.542 3.313,1.74 0.458,0.198 10 false 1 (+B) 0.042,0.094 0.271,0.271 0.229,0.177 10 false *a
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G161-1 (+B) - C174-5 (E1) IG ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C174-5 (E1) - Body ground Always Below 1 Ω



c.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

3.INSPECT ECM (IGSW VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ECM (IGSW VOLTAGE)
a.

Turn the ignition switch to ON.


b.
A080463C86
0.552,0.198 0.969,0.458 0.417,0.26 2.479,0.198 2.917,0.458 0.438,0.26 0.656,0.792 0.406,1.5 true 2.875,0.896 2.51,1.5 true 0.604,0.25 0.99,0.448 0.385,0.198 10 false C174 2.542,0.25 2.927,0.458 0.385,0.208 10 false G161 0.25,1.531 0.698,1.729 0.448,0.198 10 false 7 (E1) 2.219,1.521 2.979,1.74 0.76,0.219 10 false 11 (IGSW) 0.104,0.094 0.313,0.292 0.208,0.198 10 false *a
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G161-11 (IGSW) - C174-5 (E1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.INSPECT ECM (MREL VOLTAGE)

NG

7.INSPECT IGNITION SWITCH
4.INSPECT ECM (MREL VOLTAGE)
a.

Turn the ignition switch to ON.


b.
A080463C87
0.552,0.198 0.958,0.458 0.406,0.26 2.552,0.208 2.948,0.458 0.396,0.25 0.677,0.792 0.427,1.5 true 2.906,0.885 2.958,1.49 true 0.604,0.24 0.958,0.438 0.354,0.198 10 false C174 2.583,0.25 2.99,0.458 0.406,0.208 10 false G161 0.281,1.542 0.729,1.74 0.448,0.198 10 false 7 (E1) 2.635,1.542 3.375,1.74 0.74,0.198 10 false 10 (MREL) 0.083,0.094 0.271,0.292 0.188,0.198 10 false *a
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G161-10 (MREL) - C174-5 (E1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (EFI-MAIN NO. 1 RELAY)

NG

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (EFI-MAIN NO. 1 RELAY)
a.

Inspect the instrument panel junction block assembly (EFI-MAIN NO. 1 relay).

Click hereEngine / Hybrid System>5L-E ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - ECM, EFI-MAIN NO. 1 RELAY - BODY GROUND)

NG

REPLACE EFI-MAIN NO. 1 RELAY

6.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - ECM, EFI-MAIN NO. 1 RELAY - BODY GROUND)
a.

Check the harness and connector between the instrument panel junction block (EFI-MAIN NO. 1 relay) and ECM.

i.

Disconnect the instrument panel junction block connector.


ii.

Disconnect the ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2G-5 - G161-1 (+B) Always Below 1 Ω
2P-9 - G161-10 (MREL) Always Below 1 Ω
2G-5 or G161-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
2P-9 or G161-10 (MREL) - Body ground and other terminals Always 10 kΩ or higher



iv.

Reconnect the ECM connector.


v.

Reconnect the instrument panel junction block connector.



b.

Check the harness and connector between the instrument panel junction block (EFI-MAIN NO. 1 relay) and body ground.

i.

Disconnect the instrument panel junction block connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2J-5 - Body ground Always Below 1 Ω



iii.

Reconnect the instrument panel junction block connector.



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - MAIN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT IGNITION SWITCH
a.

Disconnect the ignition switch connector.


b.
B119736C18
2.052,0.406 1.531,0.99 true 1.115,1.115 0.74,1.385 true 0.156,0.073 0.323,0.24 0.167,0.167 10 false *1 0.417,1.302 0.76,1.469 0.344,0.167 10 false AM2 2.125,0.323 2.417,0.49 0.292,0.167 10 false IG2
*1 Ignition Switch


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 (AM2) - 3 (IG2) LOCK 10 kΩ or higher
4 (AM2) - 3 (IG2) ON Below 1 Ω



c.

Reconnect the ignition switch connector.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH, IGNITION SWITCH - ECM)

NG