Home › Engine / Hybrid System › 5L-E ENGINE CONTROL › ECD SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _048946 5L-E ENGINE CONTROL _0236357 ECD SYSTEM J

5L-E ENGINE CONTROL  ECD SYSTEM  Starter Signal Circuit  


DESCRIPTION

When the engine is cranked, the intake air flow becomes slow so fuel vaporization is poor. A rich mixture is therefore necessary in order to achieve good startability. While the engine is being cranked, the battery voltage is applied to terminal STA of the ECM. The starter signal is mainly used to increase the fuel injection volume for starting and after-start injection control.

WIRING DIAGRAM

A380145E02
2.667,5.01 3.281,5.208 0.615,0.198 10 false C26 2.125,5.49 2.74,5.688 0.615,0.198 10 false D3 0.542,5.885 1.156,6.083 0.615,0.198 10 false Battery 2.26,5.969 3.375,6.177 1.115,0.208 10 false Starter Assembly 5.927,4.854 6.344,5.031 0.417,0.177 10 false ECM 5.167,3.083 5.583,3.26 0.417,0.177 10 false G160 5.281,2.896 5.458,3.052 0.177,0.156 10 false 6 3.656,1.74 4.073,1.917 0.417,0.177 10 false B2 3.656,1.906 4.906,2.115 1.25,0.208 10 false Clutch Start Switch 3.417,1.323 3.594,1.479 0.177,0.156 10 false 2 3.396,2.427 3.573,2.583 0.177,0.156 10 false 1 2.583,0.677 2.76,0.833 0.177,0.156 10 false 2 1.323,0.656 1.5,0.813 0.177,0.156 10 false 4 1.49,0.948 1.906,1.125 0.417,0.177 10 false AM2 2.24,0.958 2.656,1.135 0.417,0.177 10 false ST2 1.49,1.208 1.906,1.385 0.417,0.177 10 false G135 1.5,1.385 2.521,1.583 1.021,0.198 10 false Ignition Switch 0.458,1.865 2.031,2.063 1.573,0.198 10 false STRG LOCK/AM2 NO. 1 1.281,2.615 1.927,2.813 0.646,0.198 10 false ST NO. 1 3.583,3.75 4.229,3.948 0.646,0.198 10 false ST NO. 1 2.833,4.792 3.01,4.948 0.177,0.156 10 false 1 2.146,5.302 2.323,5.458 0.177,0.156 10 false 1 3.385,4.146 3.563,4.302 0.177,0.156 10 false 1 3.385,3.354 3.563,3.51 0.177,0.156 10 false 2 2.656,3.344 2.833,3.5 0.177,0.156 10 false 5 2.656,4.125 2.833,4.281 0.177,0.156 10 false 3 5.583,3.083 6,3.26 0.417,0.177 10 false STA 2.688,5.229 3.302,5.427 0.615,0.198 10 false ST 2.417,5.49 3.031,5.688 0.615,0.198 10 false B 0.469,3.344 1.083,3.542 0.615,0.198 10 false FL MAIN

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 61 193

d.

Read the STA signal on the intelligent tester while the starter operates.

OK:
Ignition Switch Position Starter SIG
LOCK, ACC, ON OFF
START ON



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH - ECM)
2.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH - ECM)
a.

Disconnect the clutch start switch connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
B2-1 - G160-6 (STA) Always Below 1 Ω
B2-1 or G160-6 (STA) - Body ground and other terminals Always 10 kΩ higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR