DATA LIST
By reading the Data List displayed on the GTS, you can check values, including those of the switches, sensors, and actuators, without removing any parts. Reading the Data List as the first step of troubleshooting is one method of shortening diagnostic time.
In the table below, the values listed under Normal Conditions are for reference only. Do not depend solely on these values when determining whether or not a part is faulty.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Speed | Vehicle speed | Min.: 0 km/h, Max.: 255 km/h | Actual vehicle speed | Speed indicated on speedometer |
| Engine Speed | Engine speed | Min.: 0 rpm, Max.: 16383.75 rpm | 720 to 820 rpm: Idling (A/C off) after warming up engine | - |
| MAP | Absolute pressure inside intake manifold | Min.: 0 kPa, Max.: 255 kPa | ·
90 to 105 kPa: Idling ·
88 to 103 kPa: Engine running at 2,000 rpm ·
85 to 100 kPa: Engine running at 3,000 rpm |
- |
| Coolant Temp | Engine coolant temperature | Min.: -40°C, Max.: 215°C | 80 to 95°C (176 to 203°F): After warming up engine | If value -40°C (-40°F) or 140°C (284°F), sensor circuit open or shorted |
| Intake Air | Intake air temperature | Min.: -40°C, Max.: 215°C | Equivalent to temperature at intake manifold | If value -40°C (-40°F) or 140°C (284°F), sensor circuit open or shorted |
| Engine Run Time | Engine run time | Min.: 0 sec., Max.: 65535 sec. | Time after the ignition switch turned to ON | Time passed since the ignition switch was turned to ON. |
| Battery Voltage | Battery voltage | Min.: 0 V, Max.: 65.5 V | 11 to 14 V | - |
| Glow Indicator Supported | Status of the glow indicator supported | Unsupp or Supp | Supp | - |
| Glow Indicator | Status of the glow indicator | ON or OFF | - | - |
| Accel Position | Accelerator pedal position | Min.: 0%, Max.: 100% | ·
Accelerator pedal released: 0% ·
Accelerator pedal fully depressed: 100% |
- |
| Accel Sens. No.1 Volt % | Absolute Accelerator Pedal Position No. 1 | Min.: 0%, Max.: 100% | ·
Accelerator pedal released: 10 to 22% ·
Accelerator pedal fully depressed: 52 to 90% |
Read value with ignition switch ON (Do not start engine) |
| Accel Sens. No.2 Volt % | Absolute Accelerator Pedal Position No. 2 | Min.: 0%, Max.: 100% | ·
Accelerator pedal released: 24 to 40% ·
Accelerator pedal fully depressed: 68 to 95% |
Read value with ignition switch ON (Do not start engine) |
| Diesel Throttle Learn Status | Diesel throttle learning history | OK or NG | OK | - |
| Throttle Step Position | Throttle step position | Min.: 0 step, Max.: 255 step | ·
209 step: Throttle valve fully closed ·
0 step: Throttle valve fully open |
Read value with ignition switch ON (Do not start engine) |
| Injection Volume | Injection volume | Min.: 0 mm3/st, Max.: 1279.98 mm3/st | 3 to 11 mm3/st: Idling | - |
| Inj. FB Vol. for Idle | Idle stability status integral control volume | Min.: -80 mm3/st, Max.: 79 mm3/st | - | - |
| Fuel Temperature | Fuel temperature | Min.: -40°C, Max.: 215°C | Actual fuel temperature | If value -40°C (-40°F) or 140°C (284°F), sensor circuit open or shorted |
| Starter Signal | Starter signal | ON or OFF | ON: Cranking | - |
| Stop Light Switch | Stop light switch | ON or OFF | ·
ON: Brake pedal depressed ·
OFF: Brake pedal released |
- |
| A/C Signal | A/C signal | ON or OFF | ON: A/C switch is turned ON | - |
| Throttle Open Switch | Throttle open switch | ON or OFF | ON: Throttle valve fully open | - |
| Immobiliser Communication | Immobiliser communication | ON or OFF | ·
ON: Normal ·
OFF: Engine cannot be started due to immobiliser communication malfunction |
Cause of Out of Range:
·
Use of a non-registered key ·
Key battery is fully depleted |
| Check Mode | Check mode | ON or OFF | ON: Check mode ON | - |
| SPD Test Result | Check mode result for vehicle speed sensor | Compl or Incmpl | - | - |
| Complete Parts Monitor | Comprehensive component monitor | Not Avl or Avail | - | - |
| Fuel System Monitor | Fuel system monitor | Not Avl or Avail | - | - |
| Misfire Monitor | Misfire monitor | Not Avl or Avail | - | - |
| EGR/VVT Monitor | EGR/VVT monitor | Not Avl or Avail | - | - |
| EGR/VVT Monitor | EGR/VVT monitor | Compl or Incmpl | - | - |
| O2S(A/FS) Heater Monitor | O2S (A/FS) heater monitor | Not Avl or Avail | - | - |
| O2S(A/FS) Heater Monitor | O2S (A/FS) heater monitor | Compl or Incmpl | - | - |
| O2S(A/FS) Monitor | O2S (A/FS) monitor | Not Avl or Avail | - | - |
| O2S(A/FS) Monitor | O2S (A/FS) monitor | Compl or Incmpl | - | - |
| A/C Monitor | A/C monitor | Not Avl or Avail | - | - |
| A/C Monitor | A/C monitor | Compl or Incmpl | - | - |
| 2nd Air Monitor | 2nd air monitor | Not Avl or Avail | - | - |
| 2nd Air Monitor | 2nd air monitor | Compl or Incmpl | - | - |
| EVAP Monitor | EVAP monitor | Not Avl or Avail | - | - |
| EVAP Monitor | EVAP monitor | Compl or Incmpl | - | - |
| Heated Catalyst Monitor | Heated catalyst monitor | Not Avl or Avail | - | - |
| Heated Catalyst Monitor | Heated catalyst monitor | Compl or Incmpl | - | - |
| Catalyst Monitor | Catalyst monitor | Not Avl or Avail | - | - |
| Catalyst Monitor | Catalyst monitor | Compl or Incmpl | - | - |
| # Codes(Include History) | Number of codes | Min.: 0, Max.: 255 | 0 | This is the number of DTCs stored. |
| MIL | MIL status | ON or OFF | OFF | - |
| Time after DTC Cleared | Time after DTCs cleared | Min.: 0 minutes, Max.: 65535 minutes | Time after DTCs cleared | Time elapsed since the DTCs were cleared (or shipment from the factory). |
| Distance from DTC Cleared | Distance driven after DTCscleared | Min.: 0 km, Max.: 65535 km | Distance driven after DTCs cleared | ·
Distance driven since the DTCs were cleared. ·
(Data List "Distance from DTC clear") - (Freeze frame data "Distance from DTC cleared") = Distance driven since the abnormality occurred. |
| Warmup Cycle Cleared DTC | Warmup cycles after DTCs cleared | Min.: 0, Max.: 255 | - | ·
Number of engine warmup cycles since DTCs were cleared. ·
(Data List "Warmup Cycle Cleared DTC") - (Freeze frame data "Warmup Cycle Cleared DTC") = Warmup cycles since the abnormality occurred. |
| OBD Requirements | Identifying OBD requirement | - | - | - |
| Number of Emission DTC | Number of emissions-related DTCs | - | - | - |
| TC and TE1 | TC and TE1 connection status for Active Test | ON or OFF | - | When the "Connect the TC and TE1" Active Test is performed, the system behaves as if TC and CG were connected. |
| ACT VSV | A/C cut status | ON or OFF | - | "Control the A/C Cut Signal" Active Test support data. |
| Brake Override System | Brake override system status | ON or OFF | ON: Brake override system operating | - |
| Model Code | Model code | - | - | Identifying model code |
| Engine Type | Engine type | - | - | Identifying engine type: 5LE |
| Cylinder Number | Cylinder number | Min.: 0, Max.: 255 | - | Identifying cylinder number: 4 |
| Transmission Type | Transmission type | - | - | - |
| Destination | Destination | - | - | Identifying destination |
| Model Year | Model year
Min.: 1900, Max.: 2155 |
- | - | Identifying model year: 20## |
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Check the values by referring to the following table.
ACTIVE TEST
Performing an Active Test enables components including the relays, VSV (Vacuum Switching Valve), and actuators, to be operated without removing any parts.
The Active Test can be performed with the GTS. ActiveTest as a first step of troubleshooting is one method ofshortening diagnostic time.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
Perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Control the A/C Cut Signal | Control the A/C cut signal | ON/OFF | Test is possible when the following conditions are met:
·
Ignition switch ON ·
Engine is stopped. ·
Shift lever in neutral |
| Connect the TC and TE1 | Turn on the TC and TE1 connection | ON/OFF | Test is possible when the following conditions are met:
·
Ignition switch ON ·
Shift lever in neutral |
| Control the Electric Cooling Fan | Control the cooling fan operation | ON/OFF | Test is possible when thefollowing conditions are met:
·
Ignition switch ON ·
Engine is stopped. ·
Shift lever in neutral |