Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _048938 2TR-FE ENGINE CONTROL _0241353 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P2102  Throttle Actuator Control Motor Circuit Low  P2103  Throttle Actuator Control Motor Circuit High  


DESCRIPTION

The throttle actuator is operated by the ECM and opens and closes the throttle valve using gears.

The opening angle of the throttle valve is detected by the throttle position sensor, which is mounted on the throttle body with motor assembly. The throttle position sensor provides feedback to the ECM. This feedback allows the ECM to appropriately control the throttle actuator and monitor the throttle opening angle as the ECM responds to driver inputs.

HINT:

This Electronic Throttle Control System (ETCS) does not use a throttle cable.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2102 Throttle Actuator Control Motor Circuit Low Both of the following conditions continue for 2.0 seconds (1 trip detection logic):
(a) The throttle actuator drive duty cycle is 80% or higher.
(b) The throttle actuator current is less than 0.5 A.
·

Open in throttle actuator circuit

·

Throttle actuator

·

ECM


Comes on DTC stored
P2103 Throttle Actuator Control Motor Circuit High Either of the following conditions is met (1 trip detection logic):
·

A motor driver IC diagnosis signal failure.

·

A motor driver IC high current limiter monitor port failure.


·

Short in throttle actuator circuit

·

Throttle actuator

·

Throttle valve

·

Throttle body with motor assembly

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM monitors the electrical current through the electronic actuator, and detects malfunctions and open circuits in the throttle actuator based on this value. If the current is outside the standard range, the ECM determines that there is a malfunction in the throttle actuator. In addition, if the throttle valve does not function properly (for example, stuck on), the ECM determines that there is a malfunction. The ECM then illuminates the MIL and stores a DTC.

Example:

When the electrical current is less than 0.5 A and the throttle actuator duty ratio exceeds 80%, the ECM interprets this as the current being outside the standard range, illuminates the MIL and stores a DTC.



MONITOR STRATEGY

Required Sensors/Components Throttle actuator (throttle body with motor assembly)
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A199313E25
3.667,1.458 3.229,0.406 3.229,0.406 3.521,0.406 false 4.833,2 5.25,1.135 5.25,1.135 5.406,1.135 false 2.656,1.99 2.448,1.198 2.448,1.198 2.615,1.198 false 1.25,1.844 1.667,2.125 0.417,0.281 10 Idling 0.427,2.115 1.656,2.354 1.229,0.24 10 Ignition Switch ON 2.125,2.031 2.521,2.281 0.396,0.25 10 [A] 3.854,1.74 4.188,1.99 0.333,0.25 10 [B] 5.49,1.042 6.208,1.25 0.719,0.208 10 Released 3.583,0.313 4.427,0.5 0.844,0.188 10 Depressed 3.479,2.74 4.677,2.927 1.198,0.188 10 2 seconds or more 5.26,3.323 5.5,3.531 0.24,0.208 10 [C] 3.625,3.042 5.24,3.229 1.615,0.188 10 16 seconds or more 2.667,1.115 3.302,1.26 0.635,0.146 10 Released

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine.

7.

With the vehicle stationary, fully depress the accelerator pedal and quickly release it [B].

8.

Check that 16 seconds or more have elapsed from the instant when the accelerator pedal is first depressed.

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P2102 or P2103.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [C] again.




FAIL-SAFE

When either of these DTCs or other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue running at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

A348507E05
4.781,1.031 5.24,1.229 0.458,0.198 10 false +BM 4.802,1.667 5.115,1.865 0.313,0.198 10 false M+ 4.792,2.531 5.104,2.729 0.313,0.198 10 false M- 4.781,3.25 5.396,3.448 0.615,0.198 10 false GE01 4.781,3.708 5.396,3.906 0.615,0.198 10 false ME01 4.781,4.313 5.094,4.51 0.313,0.198 10 false E1 5.083,4.969 5.542,5.167 0.458,0.198 10 false C146 5.521,4.979 5.979,5.177 0.458,0.198 10 false ECM 4.583,1.021 4.74,1.219 0.156,0.198 10 false 5 4.594,1.677 4.75,1.875 0.156,0.198 10 false 7 4.604,2.521 4.76,2.719 0.156,0.198 10 false 6 4.552,3.156 4.865,3.354 0.313,0.198 10 false 17 4.604,3.698 4.76,3.896 0.156,0.198 10 false 4 4.594,4.208 4.75,4.406 0.156,0.198 10 false 3 1.99,3.042 2.448,3.24 0.458,0.198 10 false C81 1.99,3.208 3.375,3.927 1.385,0.719 10 false Throttle Actuator (Built into Throttle Body with Motor Assembly) 3.552,1.438 3.708,1.635 0.156,0.198 10 false * 2.344,5.063 3.875,5.26 1.531,0.198 10 false *: Shielded 1.021,4.219 2.094,4.417 1.073,0.198 10 false Battery 0.844,3.198 1.917,3.396 1.073,0.198 10 false FL MAIN 1.323,1.26 1.938,1.458 0.615,0.198 10 false ETCS 0.844,2.167 1.615,2.365 0.771,0.198 10 false J/B-B 2.948,1.677 3.104,1.875 0.156,0.198 10 false 2 2.948,2.469 3.104,2.667 0.156,0.198 10 false 1 2.635,1.625 2.948,1.823 0.313,0.198 10 false M+ 2.656,2.719 2.969,2.917 0.313,0.198 10 false M-

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

The throttle actuator current (Throttle Motor Current) and the throttle actuator duty ratio (Throttle Motor Duty (Open) / Throttle Motor Duty (Close)) can be read using the GTS. However, the ECM shuts off the throttle actuator current when the electronic throttle control system malfunctions.



PROCEDURE

1.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (RESISTANCE OF THROTTLE ACTUATOR)
a.

Inspect the throttle body with motor assembly.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>THROTTLE BODY>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (THROTTLE BODY WITH MOTOR ASSEMBLY - ECM)

NG

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (THROTTLE BODY WITH MOTOR ASSEMBLY - ECM)
a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C81-2 (M+) - C146-7 (M+) Always Below 1 Ω
C81-1 (M-) - C146-6 (M-) Always Below 1 Ω
C81-2 (M+) or C146-7 (M+) - Body ground Always 10 kΩ or higher
C81-1 (M-) or C146-6 (M-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)
a.

Check for foreign objects between the throttle valve and the housing.

OK:

No foreign objects between the throttle valve and housing.


HINT:

Perform "Inspection After Repair" after cleaning the throttle body with motor assembly.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

4.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (THROTTLE VALVE)

NG

REMOVE FOREIGN OBJECT CLEAN THROTTLE BODY WITH MOTOR ASSEMBLY

4.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (THROTTLE VALVE)
a.

Check if the throttle valve opens and closes smoothly.

OK:

Throttle valve opens and closes smoothly.


HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

NG

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY