The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the body ECU removal/installation are shown below.
| Replacement Part or Procedure | Necessary Procedures | Effects/Inoperative when not Performed | Link |
|---|---|---|---|
| Replacement of body ECU | Initialize automatic light control system | Automatic light control system | ( )
|
1.INSPECT INJ RELAY (INJ)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage not applied to terminals 1 and 2 | 10 kΩ or higher |
| Battery voltage applied to terminals 1 and 2 | Below 1 Ω |
If the result is not as specified, replace the INJ relay.
2.INSPECT A/F HTR RELAY (A/F HTR)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage not applied to terminals 1 and 2 | 10 kΩ or higher |
| Battery voltage applied to terminals 1 and 2 | Below 1 Ω |
If the result is not as specified, replace the A/F HTR relay.
3.INSPECT IG2 RELAY (IG2)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage not applied to terminals 1 and 2 | 10 kΩ or higher |
| Battery voltage applied to terminals 1 and 2 | Below 1 Ω |
If the result is not as specified, replace the IG2 relay.
82730
4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
Remove the body ECU from the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
Inspect the EFI MAIN NO. 1 relay.
Before performing the relay inspections for the relays of instrument panel junction block assembly, inspect the EFI-MAIN NO. 1 and EFI NO. 1 fuses.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2B-1 - 2G-5 | Battery voltage not applied to terminals 2P-9 and 2J-5 | 10 kΩ or higher |
| Battery voltage applied to terminals 2P-9 and 2J-5 | Below 1 Ω | |
| 2B-1 - 2K-3 | Battery voltage not applied to terminals 2P-9 and 2J-5 | 10 kΩ or higher |
| Battery voltage applied to terminals 2P-9 and 2J-5 | Below 1 Ω | |
| 2B-1 - 2K-4 | Battery voltage not applied to terminals 2P-9 and 2J-5 | 10 kΩ or higher |
| Battery voltage applied to terminals 2P-9 and 2J-5 | Below 1 Ω | |
| 2B-1 - 2N-1 | Battery voltage not applied to terminals 2P-9 and 2J-5 | 10 kΩ or higher |
| Battery voltage applied to terminals 2P-9 and 2J-5 | Below 1 Ω |
If the result is not as specified, replace the instrument panel junction block assembly.
Inspect the C/OPN NO. 1 relay.
Before performing the relay inspections for the relays of instrument panel junction block assembly, inspect the EFI-MAIN NO. 1 and IG2 NO. 1 fuses and EFI-MAIN NO. 1 relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2B-1 - 2K-5 | Battery voltage applied to terminals 2P-9 and 2J-5 and battery voltage not applied to terminals 2G-1 and 2P-8 | 10 kΩ or higher |
| Battery voltage applied to terminals 2P-9 and 2J-5, and 2G-1 and 2P-8 | Below 1 Ω |
If the result is not as specified, replace the instrument panel junction block assembly.
Install the body ECU to the instrument panel junction block assembly.
Install the instrument panel junction block assembly.