Home › Engine / Hybrid System › 1KD-FTV FUEL › FUEL SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _048916 1KD-FTV FUEL _0242275 FUEL SYSTEM G

1KD-FTV FUEL  FUEL SYSTEM  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

CAUTION:
A343691

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


PROCEDURE

Hide 1.INSPECT FOR FUEL LEAK

CAUTION:
·

During Active Test mode, the engine speed becomes high and the combustion noise becomes loud, so pay attention.

·

During Active Test mode, the fuel pressure becomes high. Be extremely careful not to expose your eyes, hands, or body to escaping fuel.



a.

Check that there are no fuel leaks from any part of the fuel system when the engine is stopped. If there is fuel leakage, repair or replace parts as necessary.


b.

Start the engine and check that there are no fuel leaks from any part of the fuel system. If there is fuel leakage, repair or replace parts as necessary.


c.

Slide the clamp and disconnect the return hose from the common rail assembly.


d.

Start the engine and check for fuel leaks from the return pipe.

If there is fuel leakage, replace the common rail assembly.


e.

Connect the GTS to the DLC3.


f.

Start the engine and push the GTS main switch on.


g.

Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak.

Powertrain > Engine > Active Test
Tester Display
Test the Fuel Leak
50004 234 90

h.

If the GTS is not available, fully depress the accelerator pedal quickly. Increase the engine speed to the maximum and maintain that speed for 2 seconds. Repeat this operation several times.


i.

Check that there are no fuel leaks from any part of the fuel system.

NOTICE:

A return pipe leakage of less than 10 cc (0.6 cu.in.) per minute is acceptable.


If there is fuel leakage, repair or replace parts as necessary.


j.

Reconnect the return hose to the common rail assembly, and slide the clamp to secure the hose.


Hide 2.BLEED AIR FROM FUEL SYSTEM

a.
A347260

Using the hand pump mounted on the fuel filter assembly, bleed the air from the fuel system. Continue pumping until the pump resistance increases.

NOTICE:
·

Hand pump pumping speed: Max. 2 strokes/ sec.

·

The hand pump must be pushed with a full stroke during pumping.

·

When the fuel pressure at the fuel supply pump assembly inlet port reaches a saturated pressure, the hand pump resistance increases.

·

If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank assembly. Continue pumping until the hand pump resistance increases.

·

If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank assembly and fuel filter assembly, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.

·

If air bleeding using the hand pump is incomplete, the common rail assembly pressure does not rise to the pressure range necessary for normal use, and the engine cannot be started.




b.

Check if the engine starts.

NOTICE:
·

Even if air bleeding using the hand pump has been completed, the starter may need to be cranked for 10 seconds or more to start the engine.

·

Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.

·

Use a fully-charged battery.



i.

When the engine can be started, proceed to the next step.


ii.

If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.



c.

Turn the ignition switch off.


d.

Connect the GTS to the DLC3.


e.

Turn the ignition switch to ON and turn the GTS on.


f.

Clear the DTCs.


g.

Start the engine.*1


h.

Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak.*2

Powertrain > Engine > Active Test
Tester Display
Test the Fuel Leak
50004 234 90

i.

Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3


j.

Allow the engine to idle for 3 minutes or more after performing the Active Test for the 5th time.

A271189C02
0.354,1.271 0.667,1.427 0.313,0.156 10 false *a 0.875,0.958 1.188,1.115 0.313,0.156 10 false *b 0.885,1.615 1.198,1.771 0.313,0.156 10 false *c 1.948,0.406 2.26,0.563 0.313,0.156 10 false *d 3.24,0.406 3.552,0.563 0.313,0.156 10 false *e 4.51,0.406 4.823,0.563 0.313,0.156 10 false *f 1.99,1.906 2.292,2.135 0.302,0.229 10 false *g 5.323,1.917 5.635,2.073 0.313,0.156 10 false *h 5.656,2.313 6,2.5 0.344,0.188 10 false *i 2.646,0.771 2.917,0.979 0.271,0.208 10 false *g
*a Active Test Operation *b ON
*c OFF *d 1st time
*e 2nd time *f 5th time
*g 10 seconds *h 3 minutes
*i Time - -


HINT:

When the Active Test "Test the Fuel Leak" is used to change the pump control mode, the actual fuel pressure inside the common rail assembly drops below the target fuel pressure when the Active Test is off, but this is normal and does not indicate a pump malfunction.



k.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

l.

Read Current DTCs.


m.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234
HINT:

It is necessary to clear the DTCs, as DTC P1604 or P1605 may be stored when air is bled from the fuel system after replacing or repairing fuel system parts.



n.

Repeat steps *1 to *3.


o.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

p.

Read Current DTCs.

OK:

No DTCs are output.



Hide 3.CHECK PRESSURE DISCHARGE VALVE

HINT:
·

This is the procedure for troubleshooting fuel pressure control malfunctions and combustion problems.

·

Malfunctions can be determined by checking the fuel pressure when performing a fuel cut and operating the pressure discharge valve with the GTS.

·

During "Pressure Discharge Valve Check", the GTS measures the fuel pressure while the engine is running, after the engine is stopped, and after the pressure discharge valve operates.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.

NOTICE:

The following conditions must be met:

·

Engine is idling.

·

Vehicle is stopped.

·

Fuel pressure is not extremely high (below 100000 kPa).

·

Fuel pressure is not extremely low (higher than 26000 kPa).

·

Fuel pressure sensor is normal.

·

Battery voltage is higher than 8 V.



HINT:

When the common rail assembly pressure is unstable, the fuel pressure may decrease to a level where the test cannot be performed. In this situation, wait until the common rail assembly pressure meets the test condition, and then perform the test.



d.

Enter the following menus: Powertrain / Engine / Utility / Pressure Discharge Valve Check.

Powertrain > Engine > Utility
Tester Display
Pressure Discharge Valve Check
50005 234 2109

e.

Press "Next".


f.

Press "Next" again to proceed.


g.

Select the check type for "Valve Check for Graph".

1.

Press "Next" again to proceed.

2.

Press "Start" again to proceed.

A267385C04
1.24,1.469 0.469,0.74 0.469,0.74 0.26,0.74 true 1.208,2.188 0.469,2.646 0.469,2.646 0.26,2.646 true 1.24,1.865 0.469,1.135 0.469,1.135 0.26,1.135 true 1.698,3.917 1.698,4.281 1.698,4.281 1.5,4.281 true 3.083,3.917 3.083,4.281 3.083,4.281 2.885,4.281 true 0.083,0.635 0.396,0.792 0.313,0.156 10 false *a 0.083,1.031 0.302,1.208 0.219,0.177 10 false *b 1.333,4.177 1.646,4.333 0.313,0.156 10 false *d 0.083,2.542 0.365,2.74 0.281,0.198 10 false *c 2.708,4.177 3.021,4.333 0.313,0.156 10 false *e
*a Engine Speed *b Fuel Pressure
*c Pressure Discharge Valve *d When "Start" is pressed, the pressure discharge valve check begins.
*e If "Save" is pressed after the pressure discharge valve check, the data recorded during the valve check can be saved. - -




h.

Select the check type "Close to Open Check" or "Always Closed Check".

HINT:
·

"Close to Open Check" opens the pressure discharge valve after the engine stops.

·

"Always Closed Check" holds the pressure discharge valve closed during the check.




i.

Press "Next".


j.

Perform troubleshooting based on the measurement results.

OK:

0.5 MPa or less


HINT:
·

During "Close to Open Check", if there is no large change in fuel pressure when the pressure discharge valve is closed while the engine is running and after the engine is stopped, and if the value is 0 MPa when the pressure discharge valve is open, the system is normal.

·

Perform "Always Closed Check" if the value is not 0 MPa when the pressure discharge valve is open during "Close to Open Check". If the results are the same as during "Close to Open Check", there is a pressure discharge valve operation malfunction.

·

If a large amount of fuel is leaking, the fuel pressure decreases when the engine is stopped. However, the condition of the pressure discharge valve can still be determined by comparing the measurement results of "Close to Open Check" and "Always Closed Check".


A347385C01
0.688,1.146 1,1.302 0.313,0.156 10 false *a 0.688,2.656 1,2.813 0.313,0.156 10 false *b 0.688,3.531 1,3.688 0.313,0.156 10 false *c 0.688,4.271 1,4.427 0.313,0.156 10 false *d 0.688,5.115 1,5.271 0.313,0.156 10 false *e 0.698,5.813 1.01,5.969 0.313,0.156 10 false *f 0.688,6.885 1,7.146 0.313,0.26 10 false *g 1.656,1.49 1.969,1.646 0.313,0.156 10 false *h 1.656,3.656 1.969,3.885 0.313,0.229 10 false *i 1.656,4.104 1.948,4.365 0.292,0.26 10 false *j 1.656,4.438 1.969,4.594 0.313,0.156 10 false *k 1.667,5.667 1.979,5.823 0.313,0.156 10 false *l 1.656,6.365 1.969,6.521 0.313,0.156 10 false *m 3.031,0.5 3.188,0.656 0.156,0.156 10 false ★ 1.656,2.938 1.969,3.094 0.313,0.156 10 false *h 1.656,4.969 1.969,5.125 0.313,0.156 10 false *k 1.656,5.25 1.948,5.51 0.292,0.26 10 false *j 1.656,5.979 1.969,6.135 0.313,0.156 10 false *k 1.667,6.74 1.979,6.896 0.313,0.156 10 false *l 1.656,7 1.969,7.156 0.313,0.156 10 false *k 3.938,0.5 4.094,0.656 0.156,0.156 10 false ★ 4.906,0.5 5.063,0.656 0.156,0.156 10 false ★ 3.052,1.958 3.208,2.115 0.156,0.156 10 false ★ 3.958,1.958 4.115,2.115 0.156,0.156 10 false ★ 4.927,1.958 5.083,2.115 0.156,0.156 10 false ★
*a Fuel Press
(Always Closed Check)
*b Fuel Press
(Close to Open Check)
*c Engine Speed *d Fuel Cut Operation Signal
*e Pressure Discharge Valve Operation
(Prohibition)
*f Pressure Discharge Valve Operation
(Always Closed Check)
*g Pressure Discharge Valve Operation
(Close to Open Check)
*h 0 MPa
*i 0 rpm *j On
*k Off *l Closed (on)
*m Open (on) - -
V100135

Pressure Discharge Valve Operation Start ★ Fuel Press Recorded Point




Hide 4.CHECK FUEL SYSTEM WARNING LIGHT AND DRAIN WATER

a.

w/ Multi-information Display:

Check the fuel system warning is displayed on the multi-information display, replace the fuel filter element assembly (Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL FILTER>REPLACEMENT) or drain the water in the fuel filter assembly.


b.

w/o Multi-information Display:

Check the fuel system warning light in the combination meter assembly and either replace the fuel filter element assembly (Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL FILTER>REPLACEMENT) or drain the water in the fuel filter assembly based on the instructions shown in the illustration.

A257158C02
1.677,0.26 1.865,0.417 0.188,0.156 10 false *a 3.948,0.26 4.135,0.417 0.188,0.156 10 false *b 5.75,0.26 5.938,0.417 0.188,0.156 10 false *c 1.854,0.875 2.042,1.031 0.188,0.156 10 false *d 1.854,1.115 2.042,1.271 0.188,0.156 10 false *e 1.854,1.792 2.042,1.948 0.188,0.156 10 false *d 1.854,2.031 2.042,2.188 0.188,0.156 10 false *e 2.479,1.188 2.667,1.344 0.188,0.156 10 false *f 2.479,2.146 2.729,2.365 0.25,0.219 10 false *g 3.948,0.969 4.135,1.125 0.188,0.156 10 false *h 3.948,1.927 4.135,2.083 0.188,0.156 10 false *i 5.75,0.958 5.938,1.135 0.188,0.177 10 false *j 5.75,1.927 5.979,2.115 0.229,0.188 10 false *k
*a Fuel System Warning Light *b Fuel Filter Condition
*c Necessary Procedure *d On
*e Off *f Illuminate
*g Blinking *h Clogged
*i Water Level Warning *j Replace the Fuel Filter Element Assembly
*k Drain the Water - -



c.

Drain water.

i.
A347376C01
1.708,1.917 1.708,1.219 true 1.625,1.927 1.875,2.115 0.25,0.188 10 true *1 3.031,0.948 3.25,1.135 0.219,0.188 10 false 1 2.708,1.604 2.927,1.792 0.219,0.188 10 false 2
*1 Lead Wire


Disconnect the clamp and slide the lead wire as shown in the illustration to remove it.


ii.
A347377

Disconnect the level warning switch connector.


iii.
A347378

Slide the fuel filter assembly and lift it up.


iv.
A347379C01
0.604,1.635 0.604,0.948 true 2.719,1.865 2.51,1.865 2.51,1.865 2.031,1.365 true 0.521,1.656 0.833,1.813 0.313,0.156 10 false *1 2.75,1.771 3.052,2.01 0.302,0.24 10 true *2
*1 Drain Cock
*2 Hose


Connect a hose to the drain cock. Place the other end of the hose into a container under the drain cock.


v.

Loosen the drain cock to drain water.


vi.

Operate the hand pump until fuel begins to run out.


vii.

Tighten the drain cock by hand.

NOTICE:

Do not use any tools in this procedure.



viii.
A347380

Slide the fuel filter assembly to install it.


ix.

Connect the level warning switch connector.


x.
A347381C01
1.771,1.875 1.771,1.219 true 1.698,1.885 1.979,2.094 0.281,0.208 10 true *1 3.042,0.979 3.198,1.177 0.156,0.198 10 false 2 2.604,1.688 2.76,1.885 0.156,0.198 10 false 1
*1 Lead Wire


Attach the clamp and slide the lead wire as shown in the illustration to install it.