Home › Engine / Hybrid System › 1KD-FTV FUEL › FUEL INJECTOR › from 2016.01
RM3270E _51 Engine / Hybrid System _048916 1KD-FTV FUEL _0242276 FUEL INJECTOR A

1KD-FTV FUEL  FUEL INJECTOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the injector assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Injector assembly
·

Injector compensation code registration

·

Pilot quantity learning


Engine starting (Click here)

CAUTION:
A343691

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

Replaced Parts (A) Pipes Requiring New Replacement
·

Injector assembly (including shuffling the injector assemblies between the cylinders)

·

Common rail assembly

·

Cylinder head sub-assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

No. 3 injection pipe sub-assembly

·

No. 4 injection pipe sub-assembly


·

Supply pump assembly

·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing Gear Case Assembly


Fuel inlet pipe sub-assembly



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 17940D 3.REMOVE INTERCOOLER ASSEMBLY

Hide 4.CHECK INJECTOR COMPENSATION CODE

HINT:

If the injector compensation code is not correctly registered, it may cause malfunctions.


a.

Read the injector compensation code.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION


b.

Check that the compensation code of the installed injector assembly is the same as the code registered in the ECM. If the code is not the same, register the injector compensation code on the injector assembly.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION


Hide 23701 5.REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 3 injection pipe sub-assembly, cover the outlets on the common rail assembly with tape to keep out foreign matter.

·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 3 injection pipe sub-assembly, put it in a plastic bag to prevent foreign matter from contaminating its injector assembly inlet.



a.
A347269C01
0.99,1.927 1.198,1.927 1.198,1.927 1.677,1.427 true 2.542,2.281 3.156,2.281 true 0.802,1.833 0.99,2.042 0.188,0.208 10 true *1 3.188,2.188 3.406,2.385 0.219,0.198 10 true *2
*1 No. 2 Injection Pipe Clamp
*2 No. 3 Injection Pipe Clamp


Remove the bolt and No. 2 injection pipe clamp from the No. 1 injection pipe sub-assembly and No. 2 injection pipe sub-assembly.


b.

Remove the 2 nuts and No. 3 injection pipe clamp from the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 3 injection pipe sub-assembly.


c.

Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 3 injection pipe sub-assembly from the injector assembly and common rail assembly.


Hide 23704 6.REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY

NOTICE:

If an injection pipe clamp is removed from the No. 4 injection pipe sub-assembly, replace the injection pipe clamp with a new one.


a.
A347271

Remove the 2 bolts and disconnect the 2 injection pipe clamps from the intake manifold.


b.

Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe sub-assembly from the injector assembly and common rail assembly.


Hide 23770 7.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

a.
A347278C01
0.74,1.844 0.99,2.031 0.25,0.188 10 true *1 2.052,1.469 2.281,1.667 0.229,0.198 10 true *2 0.083,0.958 0.281,1.135 0.198,0.177 10 true *3
*1 Fuel Hose
*2 No. 1 Fuel Hose
*3 No. 2 Fuel Hose
V100136

Union Bolt


Slide the 3 clamps and disconnect the fuel hose, No. 1 fuel hose and No. 2 fuel hose from the No. 2 nozzle leakage pipe assembly.


b.

Remove the union bolt, 2 bolts, No. 2 nozzle leakage pipe assembly and gasket from the intake manifold and cylinder head sub-assembly.


Hide 8.DISCONNECT ENGINE WIRE

a.

for LHD:

i.
A347272

Disconnect the connector from the diesel throttle body assembly.


ii.

Disconnect the 4 connectors from the 4 injector assemblies.


iii.

Disconnect the connector from the engine coolant temperature sensor.


iv.

Disconnect the connector from the compressor assembly.


v.

Remove the 3 bolts.


vi.

Detach the 3 clamps and disconnect the engine wire from the cylinder head cover sub-assembly.



b.

for RHD:

i.
A347273

Disconnect the connector from the diesel throttle body assembly.


ii.

Disconnect the 4 connectors from the 4 injector assemblies.


iii.

Disconnect the connector from the engine coolant temperature sensor.


iv.

Disconnect the connector from the compressor assembly.


v.

Remove the 3 bolts.


vi.

Detach the clamp and disconnect the engine wire from the cylinder head cover sub-assembly.



Hide 11201 9.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

NOTICE:

If the cylinder head cover sub-assembly is removed, replace the 4 No. 3 cylinder head cover gaskets with new ones.


a.

Disconnect the PCV hose from the cylinder head cover sub-assembly.


b.
A347274C01
0.927,2.177 1.323,2.031 1.323,2.031 1.49,2.031 true 1.521,1.927 1.781,2.125 0.26,0.198 10 false *a
*a Cutout Part


Using a small screwdriver, remove the 4 nozzle holder seals by prying between the nozzle holder seal and the cutout part of the cylinder head cover sub-assembly.


c.
A223193

Remove the 10 bolts, 2 nuts, cylinder head cover sub-assembly and cylinder head cover gasket from the cylinder head sub-assembly.


d.
A289511

Remove the 4 No. 3 cylinder head cover gaskets from the cylinder head cover sub-assembly.


Hide 23670 10.REMOVE INJECTOR ASSEMBLY

a.
A347374C01
0,0 0,0 false
V100136

Union Bolt


Remove the union bolt, 4 injector hollow screws, 5 gaskets and nozzle leakage pipe assembly from the injector assembly and cylinder head sub-assembly.

NOTICE:
·

When removing the nozzle leakage pipe assembly, place a cushion under the nozzle leakage pipe assembly.

·

Be careful not to deform or scratch the union seal surface.

·

After removing the nozzle leakage pipe assembly, put it in a plastic bag to prevent foreign matter from contaminating its injector assembly inlet.




b.
A271618

Remove the 4 bolts, 4 washers, 4 No. 1 nozzle holder clamps and 4 injector assemblies from the cylinder head sub-assembly.

HINT:

Arrange the injector assemblies, No. 1 nozzle holder clamps, washers and bolts in the correct order.



c.

Remove the O-ring from each injector assembly.


d.

Remove the 4 injection nozzle seats from the cylinder head sub-assembly.