Home › Engine / Hybrid System › 1KD-FTV ENGINE MECHANICAL › CYLINDER BLOCK › from 2016.01
RM3270E _51 Engine / Hybrid System _048915 1KD-FTV ENGINE MECHANICAL _0242492 CYLINDER BLOCK G

1KD-FTV ENGINE MECHANICAL  CYLINDER BLOCK  INSPECTION  


PROCEDURE

Hide 11448 1.INSPECT CYLINDER BLOCK OIL ORIFICE

a.

Check the cylinder block oil orifice for damage or clogging.

If necessary, replace the cylinder block oil orifice.


Hide 15605 2.INSPECT OIL CHECK VALVE SUB-ASSEMBLY

a.
A056746C06
1.813,0.938 2.042,0.375 2.042,0.375 2.094,0.375 true 2.125,0.26 2.313,0.469 0.188,0.208 10 false *a
*a Ball
V100135

Push


Push the ball of the oil check valve sub-assembly with a wooden stick to check if it is stuck.

If the ball of the oil check valve sub-assembly, replace the oil check valve sub-assembly.


Hide 15708 3.INSPECT NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.

Check the No. 1 oil nozzle sub-assembly for damage or clogging.

If necessary, replace the No. 1 oil nozzle sub-assembly.


Hide 11401 4.CLEAN CYLINDER BLOCK SUB-ASSEMBLY

a.

Using a gasket scraper, remove all the gasket material from the top surface of the cylinder block sub-assembly.


b.

Using a soft brush and solvent, thoroughly clean the cylinder block sub-assembly.


Hide 5.INSPECT CYLINDER BLOCK SUB-ASSEMBLY FOR WARPAGE

a.
A060195

Using a precision straightedge and feeler gauge, measure the surface of the cylinder block sub-assembly that contacts the cylinder head sub-assembly for warpage.

Maximum warpage:

0.1 mm (0.00394 in.)


If the warpage is more than the maximum, replace the cylinder block sub-assembly.


b.

Visually check the cylinders for vertical scratches.

If deep scratches are present, rebore all 4 cylinders. If necessary, replace the cylinder block sub-assembly.


Hide 6.INSPECT CYLINDER BORE

a.
A060194C10
0.865,1.323 1.365,1.781 1.365,1.781 1.427,1.781 false 0.875,1.292 0.75,1 0.75,1 0.698,1 false 1.583,1.01 1.427,0.75 1.427,0.75 1.385,0.75 false 2.219,0.75 2.063,0.5 2.063,0.5 2.021,0.5 false 2.771,0.552 2.667,0.302 2.667,0.302 2.635,0.302 false 1.458,1.677 1.635,1.844 0.177,0.167 10 true *e 0.51,0.885 0.698,1.042 0.188,0.156 10 false *a 1.219,0.646 1.406,0.802 0.188,0.156 10 false *b 2.427,0.208 2.615,0.375 0.188,0.167 10 false *d 1.823,0.406 2.031,0.573 0.208,0.167 10 false *c
*a No. 1
*b No. 2
*c No. 3
*d No. 4
*e Mark 1, 2 or 3


Inspect the cylinder bore diameter.

HINT:

There are 3 standard cylinder bore diameter sizes, marked 1, 2 and 3 accordingly. The mark is stamped on the cylinder block sub-assembly.


i.
A303249C06
1.198,2.427 1.323,2.427 1.323,2.427 1.604,2.844 true 2.198,2.396 2.063,2.396 2.063,2.396 1.719,2.698 true 1.01,2.323 1.208,2.5 0.198,0.177 10 false *a 2.229,2.292 2.448,2.469 0.219,0.177 10 false *b 0.969,3.635 1.188,3.813 0.219,0.177 10 false *c 1.688,3.5 2,3.698 0.313,0.198 10 false A 2.417,3.469 2.635,3.635 0.219,0.167 10 false *d 1.708,4.146 2.021,4.344 0.313,0.198 10 false C 1.698,3.813 2.01,4.01 0.313,0.198 10 false B 2.417,4.167 2.635,4.333 0.219,0.167 10 false *d
*a Axial Direction
*b Thrust Direction
*c Center
*d 10 mm (0.394 in.)
V100135

Front


A060191C11
1.813,1.146 2.042,0.948 2.042,0.948 2.135,0.948 true 2.156,0.833 2.385,1.031 0.229,0.198 10 false *a
*a Ridge Reamer


Using a cylinder gauge, measure the cylinder bore diameter at positions A, B and C in the thrust and axial directions.

Reference Value (New parts):
Item Specified Condition
STD Mark 1 96.00 to 96.01 mm (3.7795 to 3.7799 in.)
STD Mark 2 96.01 to 96.02 mm (3.7799 to 3.7803 in.)
STD Mark 3 96.02 to 96.03 mm (3.7803 to 3.7807 in.)
O/S 0.50 96.50 to 96.53 mm (3.7992 to 3.8004 in.)
O/S 0.75 96.75 to 96.78 mm (3.8090 to 3.8102 in.)
O/S 1.00 97.00 to 97.03 mm (3.8189 to 3.8201 in.)


Maximum Diameter:
Item Specified Condition
STD 96.23 mm (3.7886 in.)
O/S 0.50 96.73 mm (3.8083 in.)
O/S 0.75 96.98 mm (3.8181 in.)
O/S 1.00 97.23 mm (3.8280 in.)


If the diameter is more than the maximum, rebore all 4 cylinders. If necessary, replace the cylinder block sub-assembly.

If the wear is less than 0.2 mm (0.00787 in.), using a ridge reamer, grind the top of the cylinder.



Hide 7.CLEAN PISTON

a.

Using a groove cleaning tool or broken ring, clean the piston ring grooves.


b.

Using solvent and a brush, thoroughly clean the piston.

NOTICE:

Do not use a wire brush.



Hide 13101 8.INSPECT PISTON WITH PIN SUB-ASSEMBLY

HINT:

When replacing the piston sub-assembly (w/ pin) with a supply part,there are a number of piston diameter sizes to choose from, but there is only one size of piston pin diameter.


a.
A226797C04
2.073,1.104 1.635,0.573 1.635,0.573 1.531,0.573 false 2.302,1.188 2.708,0.573 2.708,0.573 2.802,0.573 true 1.552,1.406 0.635,1.167 0.635,1.167 0.458,1.167 true 0.281,1.063 0.458,1.24 0.177,0.177 10 false *c 2.688,2.094 2.875,2.271 0.188,0.177 10 false *d 1.344,0.469 1.51,0.646 0.167,0.177 10 false *a 2.823,0.469 3.042,0.635 0.219,0.167 10 false *b
*a Size Mark
*b Piston Pin Hole Inside Diameter Mark
*c Front Mark (Arrow)
*d Distance


Using a micrometer, measure the piston diameter according to the following conditions: 1) measure at a right angle to the piston center line, and 2) measure at the indicated distance from the piston head.

Standard Distance:

63 mm (2.48 in.)


Reference Value (New parts):
Item Specified Condition
STD Mark 1 95.92 to 95.93 mm (3.7764 to 3.7768 in.)
STD Mark 2 95.93 to 95.94 mm (3.7768 to 3.7772 in.)
STD Mark 3 95.94 to 95.95 mm (3.7772 to 3.7776 in.)
O/S 0.50 96.42 to 96.45 mm (3.7960 to 3.7972 in.)
O/S 0.75 96.67 to 96.70 mm (3.8059 to 3.8070 in.)
O/S 1.00 96.92 to 96.95 mm (3.8157 to 3.8169 in.)


Standard Pin Hole Inside Diameter:
Item Specified Condition
Mark A 34.011 to 34.015 mm (1.3390 to 1.3392 in.)
Mark B 34.015 to 34.019 mm (1.3392 to 1.3393 in.)
Mark C 34.019 to 34.023 mm (1.3393 to 1.3395 in.)



b.
A054725

Using a micrometer, measure the piston pin diameter.

Standard Piston Pin Diameter:
Item Specified Condition
Mark A 34.000 to 34.004 mm (1.3386 to 1.3387 in.)
Mark B 34.004 to 34.008 mm (1.3387 to 1.3389 in.)
Mark C 34.008 to 34.012 mm (1.3389 to 1.3391 in.)



c.

Subtract the piston pin diameter measurement from the piston pin hole inside diameter measurement.

Standard oil clearance:

0.007 to 0.015 mm (0.000276 to 0.000591 in.)


If the oil clearance is not within the specified range, replace the piston with pin sub-assembly.


d.
A226152

Inspect the piston pin fit.

i.

At 80°C (176°F), check that the piston pin can be pushed into the piston pin hole with your thumb.

If the pin can be installed at a lower temperature, replace the piston with pin sub-assembly.



Hide 9.INSPECT PISTON OIL CLEARANCE

a.
A226153C03
0.896,1.406 0.896,2.396 true 2.135,2.865 2.479,2.458 2.479,2.458 2.531,2.458 true 0.719,1.01 0.896,1.188 0.177,0.177 10 false *a 0.823,2.417 1,2.594 0.177,0.177 10 false *e 2.573,2.365 2.75,2.542 0.177,0.177 10 false *f 1.375,0.771 1.552,0.948 0.177,0.177 10 false *b 2,0.552 2.177,0.729 0.177,0.177 10 false *c 2.531,0.333 2.708,0.51 0.177,0.177 10 false *d
*a No. 1
*b No. 2
*c No. 3
*d No. 4
*e Mark 1, 2 or 3
*f Size Mark


Measure the cylinder bore diameter in the thrust direction.


b.

Subtract the piston diameter measurement from the cylinder bore diameter measurement.

Standard oil clearance:

0.07 to 0.09 mm (0.00276 to 0.00354 in.)


Maximum oil clearance:

0.14 mm (0.00551 in.)


If the oil clearance is more than the maximum, replace all 4 pistons and rebore all 4 cylinders.

If necessary, replace the cylinder block sub-assembly.

HINT:

When the cylinder block sub-assembly is replaced, use a piston with the same number mark as the cylinder diameter marked on the new cylinder block sub-assembly.



Hide 10.INSPECT RING GROOVE CLEARANCE

a.

Using a feeler gauge, measure the clearance between a new piston ring and the wall of the ring groove.

Standard Groove Clearance:
Item Specified Condition
No. 1 piston ring 0.091 to 0.135 mm (0.00358 to 0.00531 in.)
No. 2 piston ring 0.090 to 0.135 mm (0.00354 to 0.00531 in.)
Oil ring 0.030 to 0.075 mm (0.00118 to 0.00295 in.)


If the result is not as specified, replace the piston with pin sub-assembly.


Hide 11.INSPECT PISTON RING END GAP

a.

Insert the piston ring into the cylinder bore.


b.

Using a piston, push the piston ring a little beyond the bottom of the ring travel, 120 mm (4.72 in.) from the top of the cylinder block sub-assembly.


c.

Using a feeler gauge, measure the end gap.

Standard End Gap:
Item Specified Condition
No. 1 piston ring 0.27 to 0.39 mm (0.0106 to 0.0154 in.)
No. 2 piston ring 0.55 to 0.70 mm (0.0217 to 0.0276 in.)
Oil ring 0.20 to 0.40 mm (0.00787 to 0.0157 in.)


Maximum End Gap:
Item Specified Condition
No. 1 piston ring 0.85 mm (0.0335 in.)
No. 2 piston ring 1.07 mm (0.0421 in.)
Oil ring 0.77 mm (0.0303 in.)


If the end gap is more than the maximum, replace the piston ring.

If the end gap is more than the maximum even with a new piston ring, rebore all 4 cylinders or replace the cylinder block sub-assembly.


Hide 12.INSPECT PISTON PIN OIL CLEARANCE

a.
A149774C06
1.625,2.25 1.135,2.427 1.135,2.427 1.042,2.427 true 2.042,1.865 2.708,1.313 2.708,1.313 2.802,1.313 true 2.833,1.219 3.021,1.385 0.188,0.167 10 false *a 0.833,2.333 1.042,2.521 0.208,0.188 10 false *b
*a Front Mark
*b Connecting Rod Bush Inside Diameter Mark A, B or C


Using a caliper gauge, measure the inside diameter of the connecting rod bush.

Standard Bush Inside Diameter:
Item Specified Condition
Mark A 34.012 to 34.016 mm (1.3390 to 1.3392 in.)
Mark B 34.016 to 34.020 mm (1.3392 to 1.3393 in.)
Mark C 34.020 to 34.024 mm (1.3393 to 1.3395 in.)



b.

Subtract the piston pin diameter measurement from the connecting rod bush inside diameter measurement.

Standard oil clearance:

0.008 to 0.016 mm (0.000315 to 0.000630 in.)


Maximum oil clearance:

0.03 mm (0.0118 in.)


If the oil clearance is more than the maximum, replace the connecting rod sub-assembly.

If necessary, replace the piston with pin sub-assembly.


Hide 13201 13.INSPECT CONNECTING ROD SUB-ASSEMBLY

a.

Using a rod aligner and feeler gauge, check the connecting rod alignment.

i.
A303256

Check if the connecting rod sub-assembly is bent.

Maximum bend:

0.03 mm (0.00118 in.) per 100 mm (3.94 in.)


If the bend is more than the maximum, replace the connecting rod sub-assembly.


ii.
A303257

Check if the connecting rod sub-assembly is twisted.

Maximum twist:

0.15 mm (0.00591 in.) per 100 mm (3.94 in.)


If the twist is more than the maximum, replace the connecting rod sub-assembly.



Hide 13265 14.INSPECT CONNECTING ROD BOLT

a.
A271162C06
1.542,1.708 1.729,1.885 0.188,0.177 10 false *a
*a Tension Portion


Using a vernier caliper, measure the diameter of the tension portion of the connecting rod bolt.

Standard diameter:

8.5 to 8.6 mm (0.335 to 0.339 in.)


Minimum diameter:

8.3 mm (0.327 in.)


If the diameter is less than the minimum, replace the connecting rod bolt.


Hide 13601A 15.INSPECT NO. 1 BALANCESHAFT SUB-ASSEMBLY

A070168C03
0.906,1.188 0.677,0.906 0.677,0.906 0.583,0.906 true 1.833,0.719 1.281,0.25 1.281,0.25 1.24,0.25 true 2.625,0.396 3.073,0.115 3.073,0.115 3.135,0.115 true 1.052,0.146 1.24,0.323 0.188,0.177 10 false *b 3.177,0.021 3.365,0.198 0.188,0.177 10 false *c 0.365,0.802 0.573,0.979 0.208,0.177 10 false *a
*a No. 1
*b No. 2
*c No. 3


a.

Using a cylinder gauge, measure the inside diameter of the balanceshaft bearing.

Standard Bearing Inside Diameter:
Item Specified Condition
No. 1 42.000 to 42.020 mm (1.6535 to 1.6543 in.)
No. 2 41.000 to 41.020 mm (1.6142 to 1.6150 in.)
No. 3 32.000 to 32.020 mm (1.2598 to 1.2606 in.)



b.
P012238

Using a micrometer, measure the outside diameter of the No. 1 balanceshaft main journals.

Standard Main Journal Diameter:
Item Specified Condition
No. 1 41.941 to 41.960 mm (1.6512 to 1.6520 in.)
No. 2 40.931 to 40.950 mm (1.6115 to 1.6122 in.)
No. 3 31.941 to 31.960 mm (1.2575 to 1.2583 in.)



c.

Subtract the outside diameter of the No. 1 balanceshaft main journal from the inside diameter of the balanceshaft bearing.

Standard Oil Clearance:
Item Specified Condition
No. 1 0.040 to 0.079 mm (0.00157 to 0.00311 in.)
No. 2 0.050 to 0.089 mm (0.00197 to 0.00350 in.)
No. 3 0.040 to 0.079 mm (0.00157 to 0.00311 in.)


Maximum Oil Clearance:
Item Specified Condition
No. 1 0.18 mm (0.00709 in.)
No. 2 0.19 mm (0.00748 in.)
No. 3 0.18 mm (0.00709 in.)


If the clearance is more than the maximum, replace the cylinder block sub-assembly and No. 1 balanceshaft sub-assembly.


Hide 13602 16.INSPECT NO. 2 BALANCESHAFT SUB-ASSEMBLY

a.
A070169C03
3.094,0.563 3.208,0.323 3.208,0.323 3.24,0.323 false 2.49,1.104 2.99,1.51 2.99,1.51 2.99,1.573 true 1.573,1.677 2.104,2.073 2.104,2.073 2.219,2.073 true 2.25,1.958 2.458,2.115 0.208,0.156 10 false *a 2.896,1.583 3.073,1.74 0.177,0.156 10 false *b 3.25,0.229 3.417,0.385 0.167,0.156 10 false *c
*a No. 1
*b No. 2
*c No. 3


Using a cylinder gauge, measure the inside diameter of the No. 2 balanceshaft bearing.

Standard Bearing Inside Diameter:
Item Specified Condition
No. 1 42.000 to 42.020 mm (1.6535 to 1.6543 in.)
No. 2 41.000 to 41.020 mm (1.6142 to 1.6150 in.)
No. 3 32.000 to 32.020 mm (1.2598 to 1.2606 in.)



b.
P012238

Using a micrometer, measure the outside diameter of the No. 2 balanceshaft main journals.

Standard Main Journal Diameter:
Item Specified Condition
No. 1 41.941 to 41.960 mm (1.6512 to 1.6520 in.)
No. 2 40.931 to 40.950 mm (1.6115 to 1.6122 in.)
No. 3 31.941 to 31.960 mm (1.2575 to 1.2583 in.)



c.

Subtract the outside diameter of the No. 2 balanceshaft main journal from the inside diameter of the balanceshaft bearing.

Standard Oil Clearance:
Item Specified Condition
No. 1 0.040 to 0.079 mm (0.00157 to 0.00311 in.)
No. 2 0.050 to 0.089 mm (0.00197 to 0.00350 in.)
No. 3 0.040 to 0.079 mm (0.00157 to 0.00311 in.)


Maximum Oil Clearance:
Item Specified Condition
No. 1 0.18 mm (0.00709 in.)
No. 2 0.19 mm (0.00748 in.)
No. 3 0.18 mm (0.00709 in.)


If the clearance is more than the maximum, replace the cylinder block sub-assembly and No. 2 balanceshaft sub-assembly.


Hide 13411 17.INSPECT CRANKSHAFT

a.

Inspect for circle runout.

i.

Place the crankshaft on V-blocks.


ii.

Using a dial indicator, measure the circle runout at the center journal.

Maximum circle runout:

0.03 mm (0.00118 in.)


If the circle runout is more than the maximum, replace the crankshaft.



b.
A303258

Inspect the main journals and crank pins.

i.

Using a micrometer, measure the diameter of each main journal and crank pin.

Standard Main Journal Diameter:
Item Specified Condition
Mark 1 69.994 to 70.000 mm (2.7557 to 2.7559 in.)
Mark 2 69.988 to 69.994 mm (2.7554 to 2.7557 in.)
Mark 3 69.982 to 69.988 mm (2.7552 to 2.7554 in.)
U/S 0.25 69.745 to 69.755 mm (2.7459 to 2.7463 in.)
U/S 0.50 69.495 to 69.505 mm (2.7360 to 2.7364 in.)


Standard Crank Pin Diameter:
Item Specified Condition
Mark 1 58.994 to 59.000 mm (2.3226 to 2.3228 in.)
Mark 2 58.988 to 58.994 mm (2.3224 to 2.3226 in.)
Mark 3 58.982 to 58.988 mm (2.3221 to 2.3224 in.)


If the diameter is not as specified, check the connecting rod oil clearance (Click hereEngine / Hybrid System>1KD-FTV ENGINE MECHANICAL>CYLINDER BLOCK>DISASSEMBLY) and crankshaft oil clearance (Click hereEngine / Hybrid System>1KD-FTV ENGINE MECHANICAL>CYLINDER BLOCK>DISASSEMBLY). If necessary, grind or replace the crankshaft.


ii.

Check each main journal and crank pin for taper and out-of-round.

Maximum taper and out-of-round:

0.02 mm (0.000787 in.)


If the taper and out-of-round is more than the maximum, replace the crankshaft.



c.

If necessary, grind and hone the main journals and/or crank pins.

i.

Grind and hone the main journals and/or crank pins to the finished undersized diameter (refer to the procedures above).


ii.

Install new main journal and/or crank pin undersized bearings.



Hide 11416 18.INSPECT CRANKSHAFT BEARING CAP SET BOLT

a.
A226806C06
1.479,1.458 1.688,1.635 0.208,0.177 10 false *a
*a Measuring Area


Using a vernier caliper, measure the diameter of the crankshaft bearing cap set bolt in the measuring area.

Standard diameter:

13.5 to 14.0 mm (0.531 to 0.551 in.)


Minimum diameter:

12.6 mm (0.496 in.)


If the diameter is less than the minimum, replace the crankshaft bearing cap set bolt.