Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › from 2016.01
RM3270E _52 Drivetrain _048958 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0239141 AUTOMATIC TRANSMISSION SYSTEM C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0500  Vehicle Speed Sensor Malfunction  


DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. The skid control ECU converts these wheel speed signals into a pulse signal and outputs it to the TCM via the combination meter. The TCM determines the vehicle speed based on the frequency of this pulse signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0500 Vehicle Speed Sensor Malfunction While the vehicle is being driven at 9 km/h (5.59 mph) or more, no vehicle speed sensor signal is transmitted to the TCM for 5 seconds or more (2-trip detection logic).
·

Open or short in speed signal SPD1 circuit

·

Combination meter system

·

TCM


Comes on DTC stored

MONITOR DESCRIPTION

The TCM assumes that the vehicle is being driven when the indicated vehicle speed is more than 9 km/h (5.59 mph). If there is no speed signal from the combination meter despite this condition being met, the TCM interprets this as a malfunction in the speed signal circuit. The TCM then illuminates the MIL and stores the DTC.

WIRING DIAGRAM

C331548E15
0.406,2.885 2.427,3.156 2.021,0.271 10 false Combination Meter Assembly 0.417,2.708 0.823,2.938 0.406,0.229 10 false G8 2.948,2.031 3.448,2.188 0.5,0.156 10 false G151 1.792,1.563 2.24,1.781 0.448,0.219 10 false +S 3.188,1.781 3.49,1.938 0.302,0.156 10 false 2 3.99,1.781 4.615,1.948 0.625,0.167 10 false 6 4.958,1.781 5.438,2.021 0.479,0.24 10 false 25 5.229,1.563 5.708,1.802 0.479,0.24 10 false SPD1 6.177,1.26 6.656,1.5 0.479,0.24 10 false 5 V 5.677,2.708 6.229,2.948 0.552,0.24 10 false G147 5.698,2.875 6.25,3.115 0.552,0.24 10 false TCM 2.094,1.781 2.573,2.021 0.479,0.24 10 false 19 2.958,2.198 4.76,2.365 1.802,0.167 10 false No. 32 Junction Connector 0.083,0.083 1.313,0.281 1.229,0.198 10 false for LHD:

C331548E16
0.417,2.885 2.438,3.156 2.021,0.271 10 false Combination Meter Assembly 0.417,2.708 0.823,2.938 0.406,0.229 10 false G8 2.823,2.188 4.844,2.458 2.021,0.271 10 false No. 14 Junction Connector 1.792,1.563 2.24,1.781 0.448,0.219 10 false +S 3.167,1.781 3.646,2.021 0.479,0.24 10 false 4 3.979,1.781 4.458,2.021 0.479,0.24 10 false 8 4.958,1.781 5.438,2.021 0.479,0.24 10 false 25 5.229,1.563 5.708,1.802 0.479,0.24 10 false SPD1 6.177,1.26 6.656,1.5 0.479,0.24 10 false 5 V 5.677,2.708 6.229,2.948 0.552,0.24 10 false G147 5.698,2.875 6.25,3.115 0.552,0.24 10 false TCM 2.094,1.781 2.573,2.021 0.479,0.24 10 false 19 2.823,2.01 3.375,2.25 0.552,0.24 10 false G115 0.083,0.083 1.313,0.281 1.229,0.198 10 false for RHD:

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the ignition switch to ON and wait for 3 seconds or more.*1

2.

Drive the vehicle at 9 km/h (5.59 mph) or more for 5 seconds or more.*2

3.

Turn the ignition switch off.

4.

Perform steps (*1) through (*2) again.



PROCEDURE

1.READ VALUE USING GTS (VEHICLE SPEED)
a.

Drive the vehicle and check whether the operation of the speedometer in the combination meter assembly is normal.

HINT:
·

The vehicle speed sensor is operating normally if the speedometer reading is normal.

·

If the speedometer does not operate, check it by following the procedure described for a speedometer malfunction.




b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / ECT / Data List.


f.

Drive the vehicle.


g.

Read the value displayed on the GTS.

Powertrain > ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual vehicle speed -
Powertrain > ECT > Data List
Tester Display
Vehicle Speed
50003 235 316
OK:

Vehicle speed displayed on the GTS and speedometer display are equal.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK COMBINATION METER SYSTEM
2.CHECK COMBINATION METER SYSTEM
a.

Inspect the circuits that send vehicle speed signals to this system in the meter system.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speed Signal Circuit


b.

During inspection for the meter section, if there is an instruction that indicates to go back to inspections for each system, proceed to the next step.


Result:
Proceed to
NEXT



NEXT

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TCM)
3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TCM)
a.

Disconnect the G8 combination meter assembly connector.


b.

Disconnect the G147 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-19 (+S) - G147-25 (SPD1) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR - TCM)
4.CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR - TCM)
a.

for LHD:

Disconnect the G151 NO. 32 junction connector.


b.

for RHD:

Disconnect the G115 NO. 14 junction connector.


c.

Disconnect the G147 TCM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
G151-6 - G147-25 (SPD1) Always Below 1 Ω

for RHD:
Tester Connection Condition Specified Condition
G115-8 - G147-25 (SPD1) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR