Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › from 2016.01
RM3270E _52 Drivetrain _048958 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0239141 AUTOMATIC TRANSMISSION SYSTEM C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0560  System Voltage  


DESCRIPTION

The battery supplies power to the TCM even when the ignition switch is off. This power allows the TCM to store data such as DTC history and freeze frame data. If the battery voltage falls below a minimum level, the TCM data is cleared and the TCM determines that there is a malfunction in the power supply circuit. The next time the engine is started, the TCM will illuminate the MIL and store the DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0560 System Voltage TCM back-up power source circuit is low voltage for 3 seconds or more (1-trip detection logic).
·

Open or short in back-up power source circuit

·

TCM


Comes on DTC stored

HINT:

If DTC P0560 is stored, the TCM does not store other DTCs.


WIRING DIAGRAM

C346802E02
0.896,1.01 1.792,1.208 0.896,0.198 10 false from Battery 2.635,1.198 3.688,1.406 1.052,0.208 10 false FL MAIN 3.0W 3.979,1.198 4.917,1.375 0.938,0.177 10 false ECU-B NO. 3 5.427,1.031 6.042,1.229 0.615,0.198 10 false G147 5.448,2.094 5.906,2.292 0.458,0.198 10 false C116 5.563,0.823 5.719,1.021 0.156,0.198 10 false 5 5.563,1.885 5.719,2.083 0.156,0.198 10 false 1 5.885,1.021 6.5,1.219 0.615,0.198 10 false BATT 5.896,2.083 6.208,2.281 0.313,0.198 10 false E1 6.115,2.792 6.573,2.99 0.458,0.198 10 false TCM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the ignition switch to ON and wait for 3 seconds or more.



PROCEDURE

1.CHECK DTC OUTPUT (ECD SYSTEM DTC P0560)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / ECT / Trouble Codes.

Powertrain > ECT > Trouble Codes
50001 235

e.

Read the DTCs using the GTS.

Result:
Result Proceed to
DTCs are not output A
P0560 is output (ECD system) B




A

2.CHECK TCM (BATTERY, GROUND)

B

2.CHECK TCM (BATTERY, GROUND)
a.

Disconnect the TCM connectors.


C216560C31
0.823,0.385 1.26,0.646 0.438,0.26 2.271,0.385 2.708,0.646 0.438,0.26 1.313,1.948 1.448,2.875 true 2.281,1.948 2.198,2.885 true 0.875,0.438 1.271,0.594 0.396,0.156 10 false C116 2.313,0.438 2.688,0.604 0.375,0.167 10 false G147 0.052,0.021 0.25,0.198 0.198,0.177 10 false *a 1.26,2.917 1.698,3.188 0.438,0.271 10 false 1 (E1) 1.969,2.917 2.604,3.167 0.635,0.25 10 false 5 (BATT)
*a Rear view of wire harness connector
(to TCM)


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G147-5 (BATT) - C116-1 (E1) Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C116-1 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TCM - BATTERY, GROUND)