Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › from 2016.01
RM3270E _52 Drivetrain _048958 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0239141 AUTOMATIC TRANSMISSION SYSTEM C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, battery voltage is applied to terminal STA of the TCM.

If the TCM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The TCM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle is driven at more than 20 km/h (12.4 mph) for over 20 seconds.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High All conditions are met for 20 seconds or more (1-trip detection logic):
(a) Battery voltage (10.5 V or higher) is applied to the TCM.
(b) Vehicle speed is 20 km/h (12.4 mph) or more.
(c) Engine speed is 1000 rpm or more.
(d) STA signal is ON.
·

Park/neutral position switch

·

Starter relay circuit

·

TCM


Comes on DTC stored

WIRING DIAGRAM

C346803E02
0.292,0.646 1.635,0.844 1.344,0.198 10 false from ST NO. 1 Fuse 0.917,1.604 1.563,1.802 0.646,0.198 10 false to Starter 2.167,2.51 2.865,2.688 0.698,0.177 10 false ST NO. 1 2.052,1.75 2.208,1.948 0.156,0.198 10 false 3 2.823,1.74 2.979,1.938 0.156,0.198 10 false 5 2.073,2.271 2.229,2.469 0.156,0.198 10 false 1 2.833,2.271 2.99,2.469 0.156,0.198 10 false 2 0.25,2.99 1.583,3.188 1.333,0.198 10 false from IG1 NO. 1 Fuse 3.333,3.135 3.49,3.333 0.156,0.198 10 false 2 3.333,2.292 3.49,2.49 0.156,0.198 10 false 5 4.531,2.271 4.688,2.469 0.156,0.198 10 false 4 4.531,2.844 4.688,3.042 0.156,0.198 10 false 7 4.521,3.406 4.677,3.604 0.156,0.198 10 false 1 3.542,2.042 3.698,2.24 0.156,0.198 10 false L 4.313,2.042 4.469,2.24 0.156,0.198 10 false B 3.521,2.885 3.833,3.083 0.313,0.198 10 false RB 4.229,2.604 4.542,2.802 0.313,0.198 10 false DL 4.24,3.167 4.552,3.365 0.313,0.198 10 false RL 3.146,3.958 3.604,4.156 0.458,0.198 10 false C22 3.146,4.146 4.927,4.51 1.781,0.365 10 false Park/Neutral Position Switch Assembly 5.135,2.719 5.75,2.917 0.615,0.198 10 false G146 5.135,3.281 5.75,3.479 0.615,0.198 10 false G146 5.135,0.656 5.594,0.854 0.458,0.198 10 false C116 5.146,2.167 5.604,2.365 0.458,0.198 10 false C116 5.146,4.594 5.604,4.792 0.458,0.198 10 false C116 5.219,0.438 5.531,0.635 0.313,0.198 10 false 11 5.208,1.948 5.521,2.146 0.313,0.198 10 false 12 5.25,2.521 5.406,2.719 0.156,0.198 10 false 8 5.26,3.083 5.417,3.281 0.156,0.198 10 false 9 5.26,4.375 5.417,4.573 0.156,0.198 10 false 1 5.938,5.198 6.323,5.396 0.385,0.198 10 false TCM 5.604,0.542 6.063,0.74 0.458,0.198 10 false STA 5.594,2.042 6.052,2.24 0.458,0.198 10 false NSW 5.604,2.604 5.76,2.802 0.156,0.198 10 false D 5.604,3.167 5.76,3.365 0.156,0.198 10 false R 5.604,4.583 5.917,4.781 0.313,0.198 10 false E1 6.26,1.865 6.656,2.052 0.396,0.188 10 false 12 V

CAUTION / NOTICE / HINT

HINT:
·

The following troubleshooting flowchart is based on the premise that the engine can be cranked normally. If the engine does not crank, proceed to the problem symptoms table.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>PROBLEM SYMPTOMS TABLE

·

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Drive the vehicle for 20 seconds or more under the following conditions:

- Engine speed is 1000 rpm or more.

- Vehicle speed is 20 km/h (12.4 mph) or more.





PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / ECT / Data List.


e.

Read the value displayed on the GTS.


f.

Crank the engine.


g.

Read the value displayed on the GTS.

Powertrain > ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter Signal Starter signal ON or OFF
·

ON: Engine cranking

·

OFF: Engine not cranking


-
Powertrain > ECT > Data List
Tester Display
Starter Signal
50003 235 193
OK:

Starter Signal is only ON when the engine is being started (during cranking).



Result:
Proceed to
OK
NG



OK

NG

2.CHECK TCM (STA VOLTAGE)
2.CHECK TCM (STA VOLTAGE)
a.
C328489C03
0.792,0.375 1.167,0.604 0.375,0.229 1.354,2.073 1.604,2.75 true 0.063,0.063 0.375,0.26 0.313,0.198 10 false *a 0.813,0.417 1.271,0.615 0.458,0.198 10 false C116 1.417,2.813 2.646,3.01 1.229,0.198 10 false 11 (STA)
*a Rear view of wire harness connector
(to TCM)


Disconnect the TCM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C116-11 (STA) - Body ground
·

Ignition switch ON

·

Shift lever in P or N


Below 2 V



Result:
Proceed to
OK
NG



OK

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
C197712C39
1.281,0.948 0.906,0.406 true 2.073,1.271 2.438,1.813 true 1.583,0.958 1.5,0.417 true 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a 0.781,0.333 1.094,0.531 0.313,0.198 10 false B 2.5,1.76 2.813,1.958 0.313,0.198 10 false L 1.271,0.313 1.583,0.51 0.313,0.198 10 false RB
*a Component without harness connected
(Park/Neutral Position Switch Assembly)


Disconnect the park/neutral position switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (B) - 5 (L) Shift lever in P Below 1 Ω
4 (B) - 5 (L) Shift lever in N Below 1 Ω
4 (B) - 5 (L) Shift lever not in P 10 kΩ or higher
4 (B) - 5 (L) Shift lever not in N 10 kΩ or higher
2 (RB) - 5 (L) Shift lever in P, R, N, D or S 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG