Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › from 2016.01
RM3270E _52 Drivetrain _048958 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0239141 AUTOMATIC TRANSMISSION SYSTEM C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0717  Turbine Speed Sensor Circuit No Signal  


DESCRIPTION

This sensor detects the rotation speed of the turbine which indicates the input speed of the transmission. By comparing the input turbine speed signal NT with the output shaft speed sensor signal SP2, the TCM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions. As a result, the gears shift smoothly.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0717 Turbine Speed Sensor Circuit No Signal All conditions are met for 5 seconds or more (2-trip detection logic):
(a) Gear shift is not being performed.
(b) Transmission is in 4th or 5th gear.
(c) Transmission input shaft speed is less than 300 rpm.
(d) Transmission output shaft speed is 1000 rpm or more.
(e) Park/neutral position switch R input signal is OFF.
(f) Shift solenoid valves and park/neutral position switch are normal.
·

Open or short in transmission revolution sensor (NT) circuit

·

Transmission revolution sensor (NT)

·

TCM

·

Automatic transmission (clutch, brake, gear, etc.)


Comes on DTC stored

Reference: Inspect using an oscilloscope.

Check the waveform of the TCM connector.

Standard:
Terminal No. (Symbol) Tool Setting Condition Specified Condition
C116-3 (NT+) - C116-2 (NT-) 1 V/DIV., 2 msec./ DIV. Engine idling (shift lever in P or N) Refer to illustration


C162170E01
2.708,0.177 3.292,0.375 0.583,0.198 10 false 1 V/DIV. 2.99,0.958 3.344,1.156 0.354,0.198 10 false GND 1.667,1.76 2.479,1.958 0.813,0.198 10 false 2 msec./DIV.

MONITOR DESCRIPTION

This DTC indicates that a pulse is not output from the transmission revolution sensor (NT) or is output only a little. The NT terminal of the TCM detects the pulse signal from the transmission revolution sensor (NT). The TCM outputs a gear shift signal by comparing the transmission revolution sensor (NT) with the transmission revolution sensor (SP2).

While the vehicle is operating in 4th or 5th gear with the shift lever in D, if the input shaft speed is less than 300 rpm*1 although the output shaft speed is 1000 rpm or more*2, the TCM detects the trouble, illuminates the MIL and stores the DTC.

HINT:
·

*1: A pulse is not output or is irregularly output.

·

*2: The vehicle speed is approximately 50 km/h (31 mph) or more.



WIRING DIAGRAM

C311452E15
5,1.156 5.156,1.354 0.156,0.198 10 false 3 5.01,2.271 5.167,2.469 0.156,0.198 10 false 2 5.177,0.906 5.635,1.104 0.458,0.198 10 false NT+ 5.188,2.042 5.646,2.24 0.458,0.198 10 false NT- 1.281,1.198 1.438,1.396 0.156,0.198 10 false 1 1.281,1.99 1.438,2.188 0.156,0.198 10 false 2 0.854,2.292 1.313,2.49 0.458,0.198 10 false C134 0.854,2.51 3.073,2.688 2.219,0.177 10 false Transmission revolution sensor (NT) 5.656,2.813 6.115,3.01 0.458,0.198 10 false C116 5.656,3.031 6.115,3.229 0.458,0.198 10 false TCM 5.854,1.885 6.167,2.083 0.313,0.198 10 false 5 V

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Perform the D Position Shift Test in Road Test and drive the vehicle for 5 seconds or more at 50 km/h (31 mph) or more.*1

Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>ROAD TEST

2.

Turn the ignition switch off.

3.

Perform steps (*1) again.



DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / ECT / Data List.


g.

According to the display on the GTS, read the Data List.

Powertrain > ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
SPD (NT) Input turbine speed (transmission revolution sensor (NT)) Min.: 0 rpm
Max.: 12750 rpm
·

Lock-up on (after warming up the engine): Value from transmission revolution sensor (NT) equal to engine speed

·

Lock-up off (idling with shift lever in N): Value from transmission revolution sensor (NT) nearly equal to engine speed


The data is displayed in increments of 50 rpm.
Powertrain > ECT > Data List
Tester Display
SPD (NT)
50003 235 141
HINT:
·

SPD (NT) is always 0 while driving:

Open or short in the sensor or circuit.

·

SPD (NT) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more:

Sensor trouble, improper installation or intermittent connection trouble in the circuit.





PROCEDURE

1.INSPECT TRANSMISSION REVOLUTION SENSOR (NT) INSTALLATION
a.
C211922C14
0.865,0.219 1.104,0.417 0.24,0.198 10 false *a 2.323,0.229 2.563,0.427 0.24,0.198 10 false *b
*a CORRECT
*b INCORRECT


Check the transmission revolution sensor (NT) installation.

OK:

The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.



Result:
Proceed to
OK
NG



OK

2.INSPECT TRANSMISSION REVOLUTION SENSOR (NT)

NG

SECURELY INSTALL OR REPLACE TRANSMISSION REVOLUTION SENSOR (NT)

2.INSPECT TRANSMISSION REVOLUTION SENSOR (NT)
a.
C206284C25
1.302,1.688 1.604,1.146 true 2.146,1.688 1.792,1.146 true 0.073,0.083 0.313,0.281 0.24,0.198 10 false *a 1.219,1.708 1.667,1.906 0.448,0.198 10 false 2 2.156,1.698 2.604,1.896 0.448,0.198 10 false 1
*a Component without harness connected
(Transmission Revolution Sensor (NT))


Disconnect the transmission revolution sensor (NT) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 560 to 680 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NT) - TCM)

NG

REPLACE TRANSMISSION REVOLUTION SENSOR (NT)

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NT) - TCM)
a.
C328831C28
0.802,0.375 1.188,0.646 0.385,0.271 1.219,1.979 1.677,2.833 true 0.708,2.813 1.156,1.99 true 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a 0.833,0.427 1.292,0.625 0.458,0.198 10 false C116 0.396,2.854 1.063,3.052 0.667,0.198 10 false 3 (NT+) 1.563,2.875 2.104,3.063 0.542,0.188 10 false 2 (NT-)
*a Rear view of wire harness connector
(to TCM)


Disconnect the TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C116-3 (NT+) - C116-2 (NT-) 20°C (68°F) 560 to 680 Ω
C116-3 (NT+) - Body ground Always 10 kΩ or higher
C116-2 (NT-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR