Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › from 2016.01
RM3270E _52 Drivetrain _048958 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0239141 AUTOMATIC TRANSMISSION SYSTEM C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0722  Output Speed Sensor Circuit No Signal  


DESCRIPTION

The transmission revolution sensor (SP2) detects the rotation speed of the transmission output shaft and sends signals to the TCM. The TCM determines the vehicle speed based on these signals. An AC voltage is generated in the transmission revolution sensor (SP2) coil as the parking gear mounted on the rear planetary gear assembly rotates, and this voltage is sent to the TCM. The parking gear on the rear planetary gear is used as the timing rotor for this sensor.

The gear shift point and lock-up timing are controlled by the TCM based on the signals from this vehicle speed sensor and the throttle position sensor signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0722 Output Speed Sensor Circuit No Signal All conditions are met for 5 seconds or more (2-trip detection logic):
(a) No signal from the transmission revolution sensor (SP2) is input to the TCM.
(b) Vehicle speed is 9 km/h (5.59 mph) or more.
(c) Park/neutral position switch is OFF.
·

Open or short in transmission revolution sensor (SP2) circuit

·

Transmission revolution sensor (SP2)

·

TCM

·

Automatic transmission (clutch, brake, gear, etc.)


Comes on DTC stored

C161208E01
2.708,0.198 3.292,0.396 0.583,0.198 10 false 2 V/DIV. 3,0.969 3.354,1.167 0.354,0.198 10 false GND 1.583,1.76 2.479,1.958 0.896,0.198 10 false 20 msec./DIV.

Reference: Inspect using an oscilloscope.

Check the waveform of the TCM connector.

Standard:
Terminal No. (Symbol) Tool Setting Condition Specified Condition
C116-30 (SP2+) - C116-29 (SP2-) 2 V/DIV., 20 msec./DIV. Vehicle speed 20 km/h (12 mph) Refer to illustration



MONITOR DESCRIPTION

The transmission revolution sensor (SP2) monitors the output shaft speed. The TCM controls the gear shift point and lock-up timing based on the signals from the transmission revolution sensor (SP2) and throttle position sensor.

If the TCM detects no signal from the transmission revolution sensor (SP2) even while the vehicle is moving, it will conclude that there is a malfunction of the transmission revolution sensor (SP2). The TCM will illuminate the MIL and store a DTC.

WIRING DIAGRAM

C311452E16
4.917,1.167 5.104,1.333 0.188,0.167 10 false 30 4.938,2.292 5.146,2.469 0.208,0.177 10 false 29 5.177,0.906 5.635,1.104 0.458,0.198 10 false SP2+ 5.188,2.042 5.646,2.24 0.458,0.198 10 false SP2- 1.281,1.198 1.438,1.396 0.156,0.198 10 false 1 1.281,1.99 1.438,2.188 0.156,0.198 10 false 2 0.844,2.292 1.302,2.49 0.458,0.198 10 false C133 0.854,2.479 3.427,2.667 2.573,0.188 10 false Transmission revolution sensor (SP2) 5.656,2.813 6.115,3.01 0.458,0.198 10 false C116 5.656,2.99 6.115,3.188 0.458,0.198 10 false TCM 5.854,1.896 6.313,2.094 0.458,0.198 10 false 5 V

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Drive the vehicle for 5 seconds or more at 9 km/h (5.59 mph) or more.*1

2.

Turn the ignition switch off.

3.

Perform step (*1) again.



DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / ECT / Data List.


g.

According to the display on the GTS, read the Data List.

Powertrain > ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
SPD (SP2) Output shaft speed (transmission revolution sensor (SP2)) Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Vehicle stopped: 0 km/h (0 mph)
(output shaft speed equal to vehicle speed)
-
Powertrain > ECT > Data List
Tester Display
SPD (SP2)
50003 235 145
HINT:
·

SPD (SP2) is always 0 while driving:

Open or short in the sensor or circuit.

·

The SPD (SP2) value displayed on the GTS is much lower than the actual vehicle speed:

Sensor trouble, improper installation, or intermittent connection trouble in the circuit.





PROCEDURE

1.INSPECT TRANSMISSION REVOLUTION SENSOR (SP2) INSTALLATION
a.
C211922C15
0.854,0.229 1.094,0.427 0.24,0.198 10 false *a 2.333,0.229 2.573,0.427 0.24,0.198 10 false *b
*a CORRECT
*b INCORRECT


Check the transmission revolution sensor (SP2) installation.

OK:

The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.



Result:
Proceed to
OK
NG



OK

2.INSPECT TRANSMISSION REVOLUTION SENSOR (SP2)

NG

SECURELY INSTALL OR REPLACE TRANSMISSION REVOLUTION SENSOR (SP2)

2.INSPECT TRANSMISSION REVOLUTION SENSOR (SP2)
a.
C206284C25
1.302,1.688 1.604,1.146 true 2.146,1.688 1.792,1.146 true 0.073,0.083 0.313,0.281 0.24,0.198 10 false *a 1.219,1.708 1.667,1.906 0.448,0.198 10 false 2 2.156,1.698 2.604,1.896 0.448,0.198 10 false 1
*a Component without harness connected
(Transmission Revolution Sensor (SP2))


Disconnect the transmission revolution sensor (SP2) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 560 to 680 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (SP2) - TCM)

NG

REPLACE TRANSMISSION REVOLUTION SENSOR (SP2)

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (SP2) - TCM)
a.
C328831C29
0.802,0.375 1.188,0.646 0.385,0.271 0.719,2.156 1.292,2.802 true 0.427,2.792 0.656,2.167 true 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a 0.823,0.417 1.281,0.615 0.458,0.198 10 false C116 0.115,2.833 0.781,3.031 0.667,0.198 10 false 30 (SP2+) 1.146,2.844 1.792,3.021 0.646,0.177 10 false 29 (SP2-)
*a Rear view of wire harness connector
(to TCM)


Disconnect the TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C116-30 (SP2+) - C116-29 (SP2-) 20°C (68°F) 560 to 680 Ω
C116-30 (SP2+) - Body ground Always 10 kΩ or higher
C116-29 (SP2-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR