Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › from 2016.01
RM3270E _52 Drivetrain _048958 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0239141 AUTOMATIC TRANSMISSION SYSTEM C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0976  Shift Solenoid "B" Control Circuit Low (Shift Solenoid Valve S2)  P0977  Shift Solenoid "B" Control Circuit High (Shift Solenoid Valve S2)  


DESCRIPTION

Shifting from 1st to 5th is performed in combination with the ON and OFF operation of shift solenoid valves SL1, SL2, S1, S2 and SR, which are controlled by the TCM. If an open or short circuit occurs in one of the shift solenoid valves, the TCM controls the remaining normal shift solenoid valves to allow the vehicle to be operated smoothly. In the case of an open or short circuit, the TCM stops sending current to the circuit. For details, refer to the fail-safe chart.

Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>FAIL-SAFE CHART

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0976 Shift Solenoid "B" Control Circuit Low (Shift Solenoid Valve S2) TCM detects a short in the shift solenoid valve S2 circuit 2 times when shift solenoid valve S2 is operated (1-trip detection logic).
·

Short in shift solenoid valve S2 circuit

·

Shift solenoid valve S2

·

TCM


Comes on DTC stored
P0977 Shift Solenoid "B" Control Circuit High (Shift Solenoid Valve S2) TCM detects an open in the shift solenoid valve S2 circuit 2 times when shift solenoid valve S2 is not operated (1-trip detection logic).
·

Open in shift solenoid valve S2 circuit

·

Shift solenoid valve S2

·

TCM


Comes on DTC stored

MONITOR DESCRIPTION

These DTCs indicate an open or short in the shift solenoid valve S2 circuit. When there is an open or short circuit in any shift solenoid valve circuit, the TCM detects the problem, illuminates the MIL and stores the DTC. When shift solenoid valve S2 is on, if its resistance is 8 Ω or less, the TCM determines there is a short in the shift solenoid valve S2 circuit.

When shift solenoid valve S2 is off, if its resistance is 100 kΩ or higher, the TCM determines there is an open in the shift solenoid valve S2 circuit.

Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>FAIL-SAFE CHART

WIRING DIAGRAM

C311454E66
1.49,1.719 5.01,1.917 3.521,0.198 10 false Shift Solenoid Valve S2 1.521,2.719 2.292,2.958 0.771,0.24 10 false C132 1.521,2.875 5.042,3.073 3.521,0.198 10 false Transmission Wire 5.563,2.927 6.302,3.115 0.74,0.188 10 false C116 5.563,3.094 6.021,3.292 0.458,0.198 10 false TCM 3.333,1.146 3.646,1.344 0.313,0.198 10 false S2 5.146,1.135 5.583,1.323 0.438,0.188 10 false S2 3.604,1.354 3.917,1.552 0.313,0.198 10 false 15 4.927,1.375 5.24,1.573 0.313,0.198 10 false 17 5.771,0.854 6.083,1.073 0.313,0.219 10 false 12 V

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION


HINT:
·

Shift solenoid valve S2 is turned ON/OFF normally when the shift lever is in D.

TCM gear shift command 1st 2nd 3rd 4th 5th
Shift solenoid valve S2 OFF ON ON OFF OFF

·

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.




PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE S2)
a.
C214326C53
1.281,1.313 1.104,1.729 true 1.01,1.75 1.25,1.917 0.24,0.167 10 false S2 0.052,0.021 0.281,0.188 0.229,0.167 10 false *a
*a Component without harness connected
(Transmission Wire)


Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
15 (S2) - Body ground 20°C (68°F) 11 to 15 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)

NG

3.INSPECT SHIFT SOLENOID VALVE S2
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
a.
C328831C33
0.802,0.375 1.188,0.646 0.385,0.271 0.708,2.813 0.969,2.073 true 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a 0.823,0.417 1.281,0.615 0.458,0.198 10 false C116 0.479,2.865 1.146,3.063 0.667,0.198 10 false 17 (S2)
*a Rear view of wire harness connector
(to TCM)


Disconnect the TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C116-17 (S2) - Body ground 20°C (68°F) 11 to 15 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE S2
a.
C214328C04
0.052,0 0.302,0.198 0.25,0.198 10 false *a 1.792,0.26 1.99,0.479 0.198,0.219 10 false (-) 2.49,0.26 2.719,0.458 0.229,0.198 10 false (+)
*a Component without harness connected
(Shift Solenoid Valve S2)


Remove shift solenoid valve S2.

Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Shift solenoid valve S2 connector terminal - Shift solenoid valve S2 body 20°C (68°F) 11 to 15 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) → Shift solenoid valve S2 connector

·

Battery negative (-) → Shift solenoid valve S2 body


Valve moves and makes an operating noise



Result:
Proceed to
OK
NG



OK

NG