Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › from 2016.01
RM3270E _52 Drivetrain _048958 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0239141 AUTOMATIC TRANSMISSION SYSTEM C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P2742  Transmission Fluid Temperature Sensor "B" Circuit Low Input  P2743  Transmission Fluid Temperature Sensor "B" Circuit High Input  


DESCRIPTION

The No. 2 ATF temperature sensor is installed in the transmission valve body assembly.

If the TCM detects an abnormally high ATF temperature near this sensor, it illuminates the warning indicator.

HINT:
·

The temperature of the ATF easily rises when towing, climbing hills, in traffic, etc.

·

If the No. 2 ATF temperature sensor becomes short-circuited, a signal that indicates that the ATF temperature is 150°C (302°F) or higher is input into the TCM.



Vehicle conditions when the sensor is normal and when the sensor is short-circuited are indicated in the table below.

No. 2 ATF Temperature Sensor State Detection Condition Symptom Recovery Condition
Sensor is normal ATF temperature higher than 150°C (302°F) ATF temperature warning indicator remains on ATF temperature below 135°C (275°F)*1
ATF temperature higher than 130°C (266°F) Shift point too high ATF temperature below 110°C (230°F)
When conditions (a) and (b) are satisfied:
(a) ATF temperature higher than 130°C (266°F)
(b) Engine coolant temperature higher than 95°C (203°F)
Lock-up in 3rd gear*2 ATF temperature below 110°C (230°F)*1 and engine coolant temperature higher than 95°C (203°F)
Sensor is short-circuited Any conditions
·

ATF temperature warning indicator remains on

·

Shift point too high


Symptoms still occur
Engine coolant temperature higher than 95°C (203°F) Lock-up in 3rd gear*2 Symptoms still occur

HINT:

*1: When the ATF is normal, it decreases to below 135°C (275°F) within 5 minutes with the shift lever in P or N in an idling state.

*2: When ATF temperature is normal, transmission lock-up occurs in 5th gear with the shift lever in D or with the S5 range selected, and in 4th gear with the S4 range selected.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2742 Transmission Fluid Temperature Sensor "B" Circuit Low Input No. 2 ATF temperature sensor resistance is below 25 Ω for 0.5 seconds or more (1-trip detection logic).
·

Short in No. 2 ATF temperature sensor circuit

·

No. 2 ATF temperature sensor (transmission wire)

·

TCM


- DTC stored
P2743 Transmission Fluid Temperature Sensor "B" Circuit High Input No. 2 ATF temperature sensor resistance is higher than 156 kΩ for 0.5 seconds or more and either condition is met (1-trip detection logic):
(A) 15 minutes or more have elapsed after the engine start when the engine coolant temperature or intake air temperature is -29.375°C (-20.875°F) or less.
(B) 10 seconds or more have elapsed after the engine start when the engine coolant temperature and intake air temperature are higher than -29.375°C (-20.875°F).
·

Open in No. 2 ATF temperature sensor circuit

·

No. 2 ATF temperature sensor (transmission wire)

·

TCM


- DTC stored

MONITOR DESCRIPTION

The No. 2 ATF temperature sensor converts the ATF temperature into an electrical resistance value. Based on the resistance, the TCM determines the ATF temperature and detects an open or short in the No. 2 ATF temperature sensor circuit. If the resistance value of the No. 2 ATF temperature sensor is below 25 Ω*1 or higher than 156 kΩ*2, the TCM interprets this as a fault in the No. 2 ATF temperature sensor or wiring. The TCM stores the DTC.

HINT:
·

*1: 150°C (302°F) or higher is indicated regardless of the actual ATF temperature.

·

*2: -40°C (-40°F) is indicated regardless of the actual ATF temperature.

·

The ATF temperature can be checked on the GTS display.



CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Start the engine and wait for 15 minutes or more.



DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / ECT / Data List.


g.

According to the display on the GTS, read the Data List.

Powertrain > ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Temperature 2 No. 2 ATF temperature sensor value Min.: -40°C (-40°F)
Max.: 150°C (302°F)
·

After stall test: Approx. 80°C (176°F)

·

Equal to ambient temperature after cold soak


If the value is "-40°C (-40°F)" or "150°C (302°F)", the No. 2 ATF temperature sensor circuit is open or shorted.
Powertrain > ECT > Data List
Tester Display
A/T Oil Temperature 2
50003 235 162
HINT:

When DTC P2742 is output and the GTS output is 150°C (302°F) or higher, there is a short circuit.

When DTC P2743 is output and the GTS output is -40°C (-40°F), there is an open circuit.

Check the temperature displayed on the GTS in order to check if a malfunction exists.


Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
150°C (302°F) or higher Short circuit



PROCEDURE

1.INSPECT NO. 2 ATF TEMPERATURE SENSOR (TRANSMISSION WIRE)
a.
C214326C59
2.146,1.313 1.958,1.75 true 2.24,1.104 2.5,1.771 true 1.771,1.792 2.188,1.958 0.417,0.167 10 false OT2+ 0.052,0.021 0.281,0.188 0.229,0.167 10 false *a 2.396,1.792 2.792,1.958 0.396,0.167 10 false OT2-
*a Component without harness connected
(Transmission Wire)


Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (OT2-) - 9 (OT2+) Always 25 Ω to 156 kΩ
1 (OT2-) - Body ground Always 10 kΩ or higher
9 (OT2+) - Body ground Always 10 kΩ or higher


HINT:

If the resistance is out of the specified range at one of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.


Resistance (Reference):
ATF Temperature Specified Condition
10°C (50°F) 5 to 8 kΩ
25°C (77°F) 2.5 to 4.5 kΩ
110°C (230°F) 0.22 to 0.28 kΩ



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)

NG

REPAIR OR REPLACE NO. 2 ATF TEMPERATURE SENSOR (TRANSMISSION WIRE)

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
a.
C328831C36
0.802,0.375 1.188,0.646 0.385,0.271 1.344,2.156 1.698,2.792 true 0.708,2.813 1.281,2.156 true 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a 0.833,0.417 1.292,0.615 0.458,0.198 10 false C116 0.365,2.865 1.094,3.052 0.729,0.188 10 false 24 (THO2) 1.531,2.854 2.073,3.042 0.542,0.188 10 false 23 (E2)
*a Rear view of wire harness connector
(to TCM)


Disconnect the TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C116-24 (THO2) - C116-23 (E2) Always 25 Ω to 156 kΩ
C116-24 (THO2) - Body ground Always 10 kΩ or higher
C116-23 (E2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR