Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › from 2016.01
RM3270E _52 Drivetrain _048958 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0239141 AUTOMATIC TRANSMISSION SYSTEM C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P2759  Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU)  


DESCRIPTION

The amount of current flow to the shift solenoid valve SLU is controlled by the TCM. During the lock-up operation, if the current increases, the lock-up hydraulic pressure increases.

C221407E09
4.729,2.135 5.031,1.188 5.031,1.188 5.094,1.188 true 4.969,2.323 5.125,2.688 5.125,2.688 5.188,2.688 true 5.76,2.396 5.917,2.688 5.917,2.688 5.979,2.688 true 6.031,2.594 6.917,2.813 0.885,0.219 10 false Solenoid Coil 0.135,0.688 1.385,0.906 1.25,0.219 10 false Hydraulic Pressure 2.573,3.01 3.135,3.229 0.563,0.219 10 false Current 5.24,2.615 5.771,2.833 0.531,0.219 10 false Sleeve 5.167,1.104 6.01,1.323 0.844,0.219 10 false Spool Valve

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2759 Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU) Open or short is detected in the shift solenoid valve SLU circuit for 1 second or more while driving (1-trip detection logic).
·

Open or short in shift solenoid valve SLU circuit

·

Shift solenoid valve SLU

·

TCM


- DTC stored

MONITOR DESCRIPTION

When an open or short in the shift solenoid valve SLU circuit is detected, the TCM determines there is a malfunction. The TCM stores the DTC.

WIRING DIAGRAM

C352693E04
5.75,0.781 6.208,0.979 0.458,0.198 10 false 12 V 5.167,1.146 5.625,1.344 0.458,0.198 10 false SLU+ 4.927,1.354 5.385,1.552 0.458,0.198 10 false 22 5.167,2.115 5.625,2.313 0.458,0.198 10 false SLU- 5.521,3.042 5.979,3.24 0.458,0.198 10 false C116 5.521,3.219 5.979,3.417 0.458,0.198 10 false TCM 4.938,2.323 5.396,2.521 0.458,0.198 10 false 21 3.885,2.323 4.344,2.521 0.458,0.198 10 false 5 3.875,1.344 4.333,1.542 0.458,0.198 10 false 13 3.479,1.146 3.938,1.344 0.458,0.198 10 false SLU+ 3.5,2.115 3.958,2.313 0.458,0.198 10 false SLU- 1.438,1.729 3.104,1.969 1.667,0.24 10 false Shift Solenoid Valve SLU 1.25,1.333 1.708,1.531 0.458,0.198 10 false 2 1.271,2.115 1.729,2.313 0.458,0.198 10 false 1 1.719,2.667 2.167,2.823 0.448,0.156 10 false C132 1.719,2.844 3.354,3.115 1.635,0.271 10 false Transmission Wire

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.



PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLU)
a.
C214326C57
1.573,1.302 1.385,1.729 true 1.646,1.104 1.906,1.75 true 1.177,1.781 1.583,1.948 0.406,0.167 10 false SLU+ 0.052,0.021 0.281,0.188 0.229,0.167 10 false *a 1.771,1.781 2.146,1.948 0.375,0.167 10 false SLU-
*a Component without harness connected
(Transmission Wire)


Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
13 (SLU+) - 5 (SLU-) 20°C (68°F) 5.0 to 5.6 Ω
13 (SLU+) - Body ground Always 10 kΩ or higher
5 (SLU-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)

NG

3.INSPECT SHIFT SOLENOID VALVE SLU
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
a.
C328831C37
0.802,0.375 1.188,0.646 0.385,0.271 0.719,2.073 1.698,2.792 true 0.479,2.792 0.656,2.073 true 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a 0.833,0.417 1.292,0.615 0.458,0.198 10 false C116 0.208,2.865 0.938,3.052 0.729,0.188 10 false 22 (SLU+) 1.531,2.854 2.25,3.042 0.719,0.188 10 false 21 (SLU-)
*a Rear view of wire harness connector
(to TCM)


Disconnect the TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C116-22 (SLU+) - C116-21 (SLU-) 20°C (68°F) 5.0 to 5.6 Ω
C116-22 (SLU+) - Body ground Always 10 kΩ or higher
C116-21 (SLU-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE SLU
a.
C209928C31
1.771,0.969 2.219,0.385 true 1.469,0.969 1.01,0.385 true 1.76,2.948 2.208,2.354 true 1.458,2.948 1,2.354 true 0.052,0 0.365,0.198 0.313,0.198 10 false *a 2.26,0.271 2.427,0.469 0.167,0.198 10 false 1 0.896,0.26 1.063,0.458 0.167,0.198 10 false 2 2.24,2.24 2.406,2.438 0.167,0.198 10 false 1 0.885,2.25 1.052,2.448 0.167,0.198 10 false 2 1.927,3.958 2.125,4.156 0.198,0.198 10 false (-) 1.115,3.969 1.333,4.167 0.219,0.198 10 false (+)
*a Component without harness connected
(Shift Solenoid Valve SLU)


Remove shift solenoid valve SLU.

Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 2

·

Battery negative (-) → Terminal 1


Valve moves and makes an operating noise



Result:
Proceed to
OK
NG



OK

NG