Home › Engine / Hybrid System › 2GD-FTV ENGINE MECHANICAL › ENGINE ASSEMBLY › from 2016.01
RM3270E _51 Engine / Hybrid System _048923 2GD-FTV ENGINE MECHANICAL _0242429 ENGINE ASSEMBLY A

2GD-FTV ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 12361 1.INSTALL FRONT ENGINE MOUNTING INSULATOR

a.

Install the 2 front engine mounting insulators to the 2 front engine mounting brackets with the 2 nuts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 12391 2.INSTALL FRONT ENGINE MOUNTING INSULATOR RH

a.

Install the front engine mounting insulator RH to the front engine mounting insulator sub-assembly with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 82121 3.INSTALL ENGINE WIRE

a.

Install the engine wire to the engine assembly.


Hide 5.REMOVE ENGINE ASSEMBLY TO ENGINE STAND

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine assembly while it is suspended, as doing so is dangerous.



a.

Attach the engine sling device and hang the engine assembly with the chain block.


b.

Remove the engine assembly from the engine stand.


Hide 6.INSTALL ENGINE ASSEMBLY

a.

Slowly lower the engine assembly into the engine compartment.


b.

Install the engine assembly to the body with the 4 bolt and 4 nuts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:
·

Make sure to tighten the side with the nut.

·

When installing a bolt with a claw (stopper), make sure that the claw (stopper) does not damage the body of the vehicle.




c.

Remove the 3 bolts, No. 1 engine hanger upper and No. 2 engine hanger.


Hide 11355 7.INSTALL REAR END PLATE

a.

Install the rear end plate to the cylinder block with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13405 8.INSTALL FLYWHEEL SUB-ASSEMBLY

a.

Clean the bolt holes.


b.
A349457N01
1.208,0.906 0.521,1.406 0.521,1.406 0.406,1.406 true 1.917,1.031 2.635,1.406 2.635,1.406 2.771,1.406 true 0.125,1.313 0.479,1.5 0.354,0.188 10 false SST 2.802,1.313 3.156,1.5 0.354,0.188 10 false SST

Using SST, hold the crankshaft pulley.

SST
09213-58014  (91551-80840)
09330-00021  


c.

for Manual Transmission:

Install the flywheel sub-assembly to the crankshaft with the 8 bolts.

Torque:
178 N*m (1815 kgf*cm, 131 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installation.



d.
A346662C01
1.792,0.427 2.083,0.167 2.083,0.167 2.25,0.167 false 2.469,0.75 2.75,0.417 2.75,0.417 2.917,0.417 false 0.333,0.156 0.5,0.156 0.5,0.156 0.833,0.323 false 0.156,0.063 0.406,0.219 0.25,0.156 10 false *1 2.281,0.063 2.51,0.229 0.229,0.167 10 false *2 2.948,0.313 3.177,0.469 0.229,0.156 10 false *3 0.063,0.917 0.292,1.073 0.229,0.156 10 false *a 3.052,0.906 3.281,1.073 0.229,0.167 10 false *b
*1 Flywheel Sub-assembly
*2 Pump Impeller Drive Plate
*3 Rear Drive Plate Spacer
*a Engine Side
*b Transmission Side


for Automatic Transmission:

Install the flywheel sub-assembly, the pump impeller drive plate and the rear drive plate spacer to the crankshaft with the 8 bolts.

NOTICE:
·

Align either hole in the pump impeller drive plate and either hole in the rear drive plate spacer with the knock pin of the flywheel sub-assembly, and then install the flywheel sub-assembly, the pump impeller drive plate and the rear drive plate spacer to the crankshaft.

·

Do not start the engine for at least 1 hour after installation.



HINT:

As the rear drive plate spacer and pump impeller drive plate are not reversible, be sure to install them in the direction shown in the illustration.



e.
A344484N01
1.198,0.594 1.333,0.76 0.135,0.167 10 true 5 2.208,1.531 2.344,1.698 0.135,0.167 10 true 6 2.229,0.563 2.365,0.729 0.135,0.167 10 true 7 1.188,1.583 1.323,1.75 0.135,0.167 10 true 8 1.729,1.75 1.865,1.917 0.135,0.167 10 true 1 1.781,0.344 1.917,0.51 0.135,0.167 10 true 2 1.052,1.188 1.188,1.354 0.135,0.167 10 true 3 2.396,0.927 2.531,1.094 0.135,0.167 10 true 4

for Automatic Transmission:

Install and uniformly tighten and tighten the 8 bolts in several steps in the sequence shown in the illustration.

Torque:
178 N*m (1815 kgf*cm, 131 ft.*lbf)


f.

Install the crankshaft pulley cover to the crankshaft pulley with the 4 bolts.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 31250 9.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)

Hide 31210 10.INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission)

Hide 31210 11.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transmission)

Hide 32101A 13.INSTALL DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT (for Automatic Transmission)

Hide 33030 14.INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY (for Manual Transmission)

Hide 37100 15.INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Hide 37140 16.INSTALL FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)

Hide 17410 17.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 88320 18.CONNECT COOLER COMPRESSOR ASSEMBLY

a.

Temporarily install the cooler compressor assembly to the compressor mounting bracket with the 2 stud bolts.


b.

Using an E8 "TORX" socket wrench, tighten the 2 stud bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Install the 2 bolts and 2 nuts.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


d.

Connect the connector to the cooler compressor assembly.


e.

Connect the suction hose sub-assembly to the water inlet and timing chain cover with the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 27020 19.INSTALL GENERATOR ASSEMBLY

Hide 44774 20.CONNECT UNION TO CONNECTOR TUBE HOSE

a.

Connect the union to connector tube hose to the No. 1 hose to hose tube, and slide the clamp to secure the hose.


Hide 44320 21.CONNECT VANE PUMP ASSEMBLY

a.

Connect the vane pump assembly to the generator bracket with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Connect the connector to the power steering oil pressure switch.


Hide 22.CONNECT WATER HOSE SUB-ASSEMBLY

a.

Connect the water hose sub-assembly to the air conditioning unit assembly, slide the 2 clamps secure the 2 hoses.


Hide 74431 23.INSTALL BATTERY TRAY

Hide 28800 24.INSTALL BATTERY

Hide 74404B 25.INSTALL BATTERY CLAMP SUB-ASSEMBLY

a.

Install the battery clamp sub-assembly to the battery with the 2 nuts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 26.CONNECT WIRE HARNESS

a.

Connect the engine room main wire to the battery positive cable with the nut.

Torque:
7.1 N*m (72 kgf*cm, 63 in.*lbf)


b.

Attach the clamp and connect the No. 2 engine wire with the 2 bolts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


c.

Connect the 2 connectors to the engine room relay block sub-assembly.


d.

Connect the wire to wire to the engine room relay block sub-assembly with the nut.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


e.

Attach the 2 clips and install the No. 1 relay block cover side to the engine room relay block sub-assembly.


f.

Attach the 3 clips and install the No. 1 relay block cover upper to the engine room relay block sub-assembly.


Hide 23273H 27.CONNECT NO. 2 FUEL HOSE

a.

Connect the No. 2 fuel hose to the No. 3 nozzle leakage pipe assembly, and slide the clamp to secure the hose.


b.

Attach the clamp to the No. 2 fuel hose.


Hide 23271H 28.CONNECT NO. 1 FUEL HOSE

a.

Connect the No. 1 fuel hose to the No. 2 fuel pipe, and slide the clamp to secure the hose.


b.

Attach the clamp to the No. 1 fuel hose.


Hide 23300 29.INSTALL FUEL FILTER ASSEMBLY

Hide 17363K 30.INSTALL INTERCOOLER AIR TUBE

a.

Install the intercooler air tube to the diesel throttle body assembly, and slide the clamp to secure the hose.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


b.

Connect the connector to the intake air temperature sensor.


Hide 17344E 31.INSTALL NO. 4 AIR TUBE

a.

Install the No. 4 air hose to the No. 2 air tube and intercooler air tube, and slide the 2 clamps to secure the hose.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


b.

Connect the oil return hose to the engine oil level dipstick guide assembly, and slide the clamp to secure the hose.


Hide 17341F 32.INSTALL NO. 1 AIR HOSE

a.

Install the No. 1 air hose to the compressor outlet elbow and No. 1 air tube, and slide the 2 clamps to secure the 2 hoses.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


Hide 17801 33.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 34.INSTALL AIR CLEANER CAP AND HOSE

a.

Attach the 4 clips and install the air cleaner cap and hose.


b.

Tighten the hose clamp.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


c.

Attach the 2 clamp and connect the connector to the mass air flow meter.


Hide 82121 35.CONNECT ENGINE WIRE

a.

Pass the engine wire into the cabin.


b.

Attach the grommet to the body.

HINT:
A340273N01
1.958,0.167 2.271,0.354 0.313,0.188 10 true 45° 1.198,0.083 1.49,0.26 0.292,0.177 10 true 45°

Make sure the direction of grommet is shown in the illustration.



c.

Attach the clamp to connect the engine wire to the bracket.


d.

Attach the clamp and connect the 4 connectors to the glow plug controller.


e.

Connect the connector to the engine room main wire.


f.

Attach the 2 clamps and connect the 3 connectors to the instrument panel wire.



Hide 16400 36.INSTALL RADIATOR ASSEMBLY

Hide 53301 37.INSTALL HOOD SUB-ASSEMBLY

a.

Install the hood sub-assembly to the 2 hood hinge assemblies with the 4 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


b.

Connect the washer nozzle hose to the hood sub-assembly.


Hide 39.ADD MANUAL TRANSMISSION OIL (for Manual Transmission)

Hide 41.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 46.INSPECT ENGINE IDLE SPEED AND MAXIMUM SPEED

Hide 12601B 47.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 51442 48.INSTALL NO. 2 ENGINE UNDER COVER

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

Hide 51410 49.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

Torque:
for M6 bolt : 11.5 N*m (117 kgf*cm, 8 ft.*lbf)
for M8 bolt : 28 N*m (286 kgf*cm, 21 ft.*lbf)