Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/ Smart Entry and Start System) › from 2016.01
RM3270E _58 Vehicle Interior _041706 THEFT DETERRENT / KEYLESS ENTRY _0212880 IMMOBILISER SYSTEM(w/ Smart Entry and Start System) U

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Smart Entry and Start System)  TERMINALS OF ECU  


CHECK ENGINE SWITCH


B271001N43
3.354,0.229 3.729,0.458 0.375,0.229 3.417,0.271 4.073,0.635 0.656,0.365 10 false G45

a.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
G45-6 (AGND) - Body ground - SB - Body ground Transponder key amplifier ground Always Below 1 Ω -
G45-7 (TXCT) - G45-6 (AGND) Input R - SB Immobiliser communication input Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V -
G45-8 (CODE) - G45-6 (AGND) Output Y - SB Immobiliser communication output Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V -
G45-10 (VC5) - G45-6 (AGND) Input LG - SB Transponder key amplifier power supply Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V -

*1: for Automatic Transmission

*2: for Manual Transmission



b.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
G45-7 (TXCT) - G45-6 (AGND) Input R - SB Signal input from certification ECU (smart key ECU assembly)
(Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into engine switch, and then transmitted by transponder key amplifier antenna as radio waves)
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed Pulse generation
(See waveform 1)
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response

HINT:

If immobiliser key code verification communication is not performed correctly, the malfunction may be indicated by one or more of the Data List items listed above



G45-8 (CODE) - G45-6 (AGND) Output Y - SB Signal output to certification ECU (smart key ECU assembly)
(Radio waves from transponder key amplifier built into engine switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly).)
Engine switch off, engine switch pressed with key held near engine switch* Pulse generation
(See waveform 2)
G45-10 (VC5) - G45-6 (AGND) Input LG - SB Transponder key amplifier power supply
(Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into engine switch activated)
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed Pulse generation
(See waveform 3)

HINT:

*: Remove the key battery before performing this inspection.



c.

Using an oscilloscope, check the waveform.

HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B051052N18
2.802,0.781 3.156,0.969 0.354,0.188 10 GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection G45-7 (TXCT) - G45-6 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed


ii.
B251418C18
1.844,0.802 2.635,1.542 2.635,1.542 2.75,1.542 true 2.781,1 3.219,1.167 0.438,0.167 10 false GND 2.781,1.458 2.958,1.625 0.177,0.167 10 false *a
*a Key held near engine switch


Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection G45-8 (CODE) - G45-6 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, engine switch pressed with key held near engine switch*

HINT:

*: Remove the key battery before performing this inspection.



iii.
B216007N05
2.885,1.031 3.427,1.375 0.542,0.344 10 GND

Waveform 3 (Reference)

Measurement Condition
Item Content
Tester Connection G45-10 (VC5) - G45-6 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed




CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


B391999E01
2.281,0.583 2.781,0.833 0.5,0.25 4.052,0.583 4.552,0.833 0.5,0.25 2.396,0.635 2.854,0.833 0.458,0.198 10 false G16 4.167,0.635 4.625,0.833 0.458,0.198 10 false G17

a.

Disconnect the G16 and G17 certification ECU (smart key ECU assembly) connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
G16-1 (+B) - G16-10 (E) Input P - BR +B power supply Always 11 to 14 V -
G17-33 (CUTB) - G16-10 (E) Input W - BR Stand-by power Always 11 to 14 V -
G16-10 (E) - Body ground - BR - Body ground Ground Always Below 1 Ω -


c.

Reconnect the G16 and G17 certification ECU (smart key ECU assembly) connectors.


d.

Measure the resistance, voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
G16-15 (IND) - G16-10 (E) Output Y - BR Security indicator light output Engine switch off → on (IG) Pulse generation
→ Below 2 V
-
G17-2 (TXCT) - G16-24 (AGND) Output R - SB Signal output to transponder key amplifier Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response


G17-1 (CODE) - G16-24 (AGND) Input Y - SB Signal input from transponder key amplifier Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V
G17-20 (VC5) - G16-24 (AGND) Output LG - SB Transponder key amplifier power supply Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V
G16-24 (AGND) - Body ground - SB - Body ground Transponder key amplifier ground Always Below 1 Ω

*1: for Automatic Transmission

*2: for Manual Transmission



e.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
G17-2 (TXCT) - G16-24 (AGND) Output R - SB Signal output to transponder key amplifier
(Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into engine switch, and then transmitted by transponder key amplifier antenna as radio waves)
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed Pulse generation
(See waveform 1)
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response


G17-1 (CODE) - G16-24 (AGND) Input Y - SB Signal input from transponder key amplifier
(Radio waves from transponder key amplifier built into engine switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly).)
Engine switch off, engine switch pressed with key held near engine switch*1 Pulse generation
(See waveform 2)
G17-20 (VC5) - G16-24 (AGND) Output LG - SB Transponder key amplifier power supply
(Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into engine switch activated)
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed Pulse generation
(See waveform 3)
G16-3 (EFII) - G16-24 (AGND)*2 Input Y - SB EFI communication input
(Signal input from ECM to certification ECU (smart key ECU assembly))
Engine switch off 11 to 14 V
·

B2799

·

B279A

·

Engine Start Request

·

EFI Code Receive


G16-3 (EFII) - G16-24 (AGND)*2 Input Y - SB EFI communication input
(Signal input from ECM to certification ECU (smart key ECU assembly))
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 4)
G17-35 (EFIO) - G16-24 (AGND)*2 Output B - SB EFI communication output
(Signal output from certification ECU (smart key ECU assembly) to ECM)
Engine switch off Below 1 V
G17-35 (EFIO) - G16-24 (AGND)*2 Output B - SB EFI communication output
(Signal output from certification ECU (smart key ECU assembly) to ECM)
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 5)

HINT:

*1: Remove the key battery before performing this inspection.


*2: w/o ID Code Box (Immobiliser Code ECU)



f.

Using an oscilloscope, check the waveform.

HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B051052N19
2.802,0.781 3.156,0.969 0.354,0.188 10 GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection G17-2 (TXCT) - G16-24 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed


ii.
B251418C18
1.844,0.802 2.635,1.542 2.635,1.542 2.75,1.542 true 2.781,1 3.219,1.167 0.438,0.167 10 false GND 2.781,1.458 2.958,1.625 0.177,0.167 10 false *a
*a Key held near engine switch


Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection G17-1 (CODE) - G16-24 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, engine switch pressed with key held near engine switch*

HINT:

*: Remove the key battery before performing this inspection.



iii.
B216007N06
2.885,1.031 3.427,1.375 0.542,0.344 10 GND

Waveform 3 (Reference)

Measurement Condition
Item Content
Tester Connection G17-20 (VC5) - G16-24 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed


iv.

Waveform 4 (Reference)

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection G16-3 (EFII) - G16-24 (AGND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected


v.

Waveform 5 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection G17-35 (EFIO) - G16-24 (AGND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected




CHECK ID CODE BOX (IMMOBILISER CODE ECU) (w/ ID Code Box [Immobiliser Code ECU])


a.

Disconnect the G138 ID code box (immobiliser code ECU) connector.


b.
B302477E07
1.542,0.563 1.938,0.771 0.396,0.208 1.573,0.583 2.031,0.781 0.458,0.198 10 false G138

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC

If the result is not as specified, there may be a malfunction on the wire harness side.

G138-1 (+B) - Body ground Input L - Body ground +B power supply Always 11 to 14 V B2789
G138-5 (GND) - Body ground - BR - Body ground Ground Always Below 1 Ω B2789


c.

Reconnect the G138 ID code box (immobiliser code ECU) connector.


d.

Measure the voltage and check the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
G138-3 (EFII) - G138-5 (GND) Input Y - BR EFI communication input (Signal input from ECM to certification ECU [smart key ECU assembly]) Engine switch off 11 to 14 V
·

B2799

·

B279A

·

Engine Start Request

·

EFI Code Receive


G138-4 (EFIO) - G138-5 (GND) Output B - BR EFI communication output (Signal output from certification ECU [smart key ECU assembly] to ECM) Engine switch off Below 1 V
G138-3 (EFII) - G138-5 (GND) Input Y - BR EFI communication input (Signal input from ECM to certification ECU [smart key ECU assembly]) Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation (See waveform 1)
G138-4 (EFIO) - G138-5 (GND) Output B - BR EFI communication output (Signal output from certification ECU [smart key ECU assembly] to ECM) Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation (See waveform 2)


e.

Inspect using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection G138-3 (EFII) - G138-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected


ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection G138-4 (EFIO) - G138-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected




CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)


B118684N83
3.458,0.188 3.833,0.406 0.375,0.219 3.521,0.229 3.844,0.396 0.323,0.167 10 false G19

a.

Measure the voltage, resistance and check for pulses to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
G19-1 (GND) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
G19-3 (IGE) - G19-1 (GND) Input L - W-B Steering lock motor operation permission signal (motor operation permission signal supplied by certification ECU (smart key ECU assembly)) Steering lock motor operates when both conditions met, and then door opened:
·

Shift lever in P*1

·

Key carried, engine switch turned on (IG), steering unlocked, and then engine switch turned off


Pulse generation
(See waveform 1)
·

Power Supply Short

·

Unlock Request Receive

·

Lock Request Receive


G19-4 (SLP1) - G19-1 (GND) Output R - W-B Steering lock bar position signal (signal output from steering unlock sensor) Steering locked → unlocked*2 11 to 14 V → Below 1.5 V
·

Push Start Error

·

Sensor Value


G19-6 (IG2) - G19-1 (GND) Input P - W-B IG signal (IG2 power supply input for steering lock motor) Engine switch off → on (IG) Below 1 V → 11 to 14 V B2788
G19-7 (B) - Body ground Output W - Body ground Constant power supply Always 11 to 14 V B2788

*1: for Automatic Transmission


If the result is not as specified, the steering lock ECU (steering lock actuator assembly) may be malfunctioning.

HINT:

*2: The steering locks when any door is opened with the shift lever in P*1 and the engine switch off. The steering unlocks when the engine switch is turned on (ACC).



b.

Using an oscilloscope, check the waveform.

HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
C259594C03
1.052,0.344 2.958,0.219 2.958,0.219 2.521,0.396 true 2.031,1.802 2.292,1.969 true 3.01,0.135 3.323,0.292 0.313,0.156 10 *a 2.344,1.938 2.667,2.104 0.323,0.167 10 *b 2.938,1.594 3.302,1.792 0.365,0.198 10 GND
*a Steering lock motor not operating
*b Steering lock motor operating


Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection G19-3 (IGE) - G19-1 (GND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Steering lock motor operates when both conditions met, and then door opened:
·

Shift lever in P*

·

Key carried, engine switch turned on (IG), steering unlocked, and then engine switch turned off



*: for Automatic Transmission





CHECK ECM (for 2TR-FE)


A352214E05
0.74,0.469 1.125,0.781 0.385,0.313 1.969,0.479 2.385,0.771 0.417,0.292 3.375,0.469 3.802,0.76 0.427,0.292 4.771,0.51 5.208,0.781 0.438,0.271 6.083,0.521 6.49,0.792 0.406,0.271 0.781,0.542 1.24,0.74 0.458,0.198 10 false C146 2.021,0.542 2.479,0.74 0.458,0.198 10 false C147 3.427,0.542 3.885,0.74 0.458,0.198 10 false C148 4.844,0.563 5.302,0.76 0.458,0.198 10 false G142 6.135,0.573 6.594,0.771 0.458,0.198 10 false G143

a.

Measure the resistance, voltage and check for pulses according to the value(s) in the table below.

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item

*1: w/o ID Code Box (Immobiliser Code ECU)

*2: w/ ID Code Box (Immobiliser Code ECU)

C146-3 (E1) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C146-4 (ME01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C146-1 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C147-5 (E04) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C146-2 (E02) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
G143-1 (+B) - C146-3 (E1) Input L - W-B IG power supply Engine switch on (IG) 11 to 14 V -
G143-2 (+B2) - C146-3 (E1) Input B - W-B IG power supply Engine switch on (IG) 11 to 14 V -
G143-3 (BATT) - C146-3 (E1) Input Y - W-B +B power supply Always 11 to 14 V -
G142-9 (IMO) - C146-3 (E1) Output Y - W-B Certification ECU (smart key ECU assembly) communication output*1
ID code box (immobiliser code ECU) communication output*2
Engine switch off 11 to 14 V E/G Start Permission
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 1)
E/G Start Permission
G142-10 (IMI) - C146-3 (E1) Input B - W-B Certification ECU (smart key ECU assembly) communication input*1
ID code box (immobiliser code ECU) communication input*2
Engine switch off Below 1 V E/G Start Permission
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 2)
E/G Start Permission


b.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B333258C03
0.865,1.271 1.323,1.469 0.458,0.198 10 GND 2.719,1.354 2.885,1.521 0.167,0.167 10 *a 2.906,1.354 3.073,1.521 0.167,0.167 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection G142-9 (IMO) - C146-3 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 2 (Reference)

B333259C05
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection G142-10 (IMI) - C146-3 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal




CHECK ECM (for 1GR-FE)


A225776E28
0.625,0.427 1.052,0.646 0.427,0.219 1.625,0.448 2.052,0.667 0.427,0.219 3.125,0.438 3.552,0.656 0.427,0.219 4.115,0.448 4.542,0.667 0.427,0.219 5.115,0.448 5.542,0.667 0.427,0.219 6.219,0.427 6.646,0.646 0.427,0.219 0.667,0.448 1.042,0.677 0.375,0.229 10 false G144 1.667,0.458 2.042,0.688 0.375,0.229 10 false G145 3.219,0.469 3.594,0.698 0.375,0.229 10 false C85 4.219,0.479 4.594,0.708 0.375,0.229 10 false C84 5.208,0.479 5.583,0.708 0.375,0.229 10 false C83 6.302,0.469 6.677,0.698 0.375,0.229 10 false C82

a.

Measure the resistance, voltage and check for pulses according to the value(s) in the table below.

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item

*1: w/o ID Code Box (Immobiliser Code ECU)

*2: w/ ID Code Box (Immobiliser Code ECU)

C83-12 (E1) - Body ground - BR - Body ground Ground Always Below 1 Ω -
C83-29 (ME01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C83-23 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C82-16 (E04) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C82-14 (E02) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
G144-23 (+B) - C83-12 (E1) Input L - BR IG power supply Engine switch on (IG) 11 to 14 V -
G144-22 (+B2) - C83-12 (E1) Input B - BR IG power supply Engine switch on (IG) 11 to 14 V -
G144-24 (BATT) - C83-12 (E1) Input Y - BR +B power supply Always 11 to 14 V -
G145-8 (IMO) - C83-12 (E1) Output Y - BR Certification ECU (smart key ECU assembly) communication output*1
ID code box (immobiliser code ECU) communication output*2
Engine switch off 11 to 14 V E/G Start Permission
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 1)
E/G Start Permission
G145-10 (IMI) - C83-12 (E1) Input B - BR Certification ECU (smart key ECU assembly) communication input*1
ID code box (immobiliser code ECU) communication input*2
Engine switch off Below 1 V E/G Start Permission
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 2)
E/G Start Permission


b.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B333258C03
0.865,1.271 1.323,1.469 0.458,0.198 10 GND 2.719,1.354 2.885,1.521 0.167,0.167 10 *a 2.906,1.354 3.073,1.521 0.167,0.167 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection G145-8 (IMO) - C83-12 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 2 (Reference)

B333259C05
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection G145-10 (IMI) - C83-12 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal




CHECK ECM (for 1GD-FTV, 2GD-FTV)


A340466E01
0.531,0.438 0.969,0.677 0.438,0.24 1.74,0.438 2.177,0.677 0.438,0.24 2.844,0.438 3.281,0.677 0.438,0.24 3.885,0.438 4.323,0.677 0.438,0.24 5,0.438 5.438,0.677 0.438,0.24 6.156,0.438 6.594,0.677 0.438,0.24 1.844,0.469 2.156,0.667 0.313,0.198 10 false C39 0.635,0.469 0.948,0.667 0.313,0.198 10 false C38 2.938,0.469 3.25,0.667 0.313,0.198 10 false C40 3.99,0.469 4.302,0.667 0.313,0.198 10 false C41 5.083,0.469 5.396,0.667 0.313,0.198 10 false G49 6.25,0.469 6.563,0.667 0.313,0.198 10 false G50

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC

*1: w/o ID Code Box (Immobiliser Code ECU)

*2: w/ ID Code Box (Immobiliser Code ECU)

C41-1 (E1) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
G50-1 (BATT) - C41-1 (E1) Input Y - W-B +B power supply Always 11 to 14 V -
G50-2 (+B) - C41-1 (E1) Input L - W-B +B power supply Engine switch on (IG) 11 to 14 V -
G50-3 (+B2) - C41-1 (E1) Input B - W-B +B power supply Engine switch on (IG) 11 to 14 V -
G50-17 (IMO) - C41-1 (E1) Output Y - W-B Certification ECU (smart key ECU assembly) communication output*1
ID code box (immobiliser code ECU) communication output*2
Engine switch off 11 to 14 V -
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 1)
-
G50-16 (IMI) - C41-1 (E1) Input B - W-B Certification ECU (smart key ECU assembly) communication input*1
ID code box (immobiliser code ECU) communication input*2
Engine switch off Below 1 V -
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 2)
-

a.

Using an oscilloscope, check the waveform.

HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection G50-17 (IMO) - C41-1 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected


ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection G50-16 (IMI) - C41-1 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected




CHECK ECM (for 1KD-FTV)


A254878E13
1.208,0.406 1.615,0.646 0.406,0.24 2.729,0.406 3.135,0.646 0.406,0.24 4.292,0.406 4.698,0.646 0.406,0.24 5.76,0.406 6.167,0.646 0.406,0.24 1.25,0.448 1.635,0.625 0.385,0.177 10 false C114 2.771,0.448 3.135,0.635 0.365,0.188 10 false C115 4.333,0.448 4.729,0.615 0.396,0.167 10 false G140 5.802,0.448 6.167,0.625 0.365,0.177 10 false G141

a.

Measure the resistance, voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
C115-7 (E1) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
G140-2 (BATT) - C115-7 (E1) Input Y - W-B +B power supply Always 11 to 14 V -
G141-1 (+B) - C115-7 (E1) Input L - W-B IG power supply Engine switch on (IG) 11 to 14 V -
G140-29 (IMO) - C115-7 (E1) Output Y - W-B Certification ECU (smart key ECU assembly) communication output Engine switch off 11 to 14 V -
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 1)
-
G140-30 (IMI) - C115-7 (E1) Input B - W-B Certification ECU (smart key ECU assembly) communication input Engine switch off Below 1 V -
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 2)
-


b.

Using an oscilloscope, check the waveform.

HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection G140-29 (IMO) - C115-7 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected


ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection G140-30 (IMI) - C115-7 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected