CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
Disconnect the G16 and G17 certification ECU (smart key ECU assembly) connectors.
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connector disconnected.
| Tester Connection | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|---|
| G16-10 (E) - Body ground | - | BR - Body ground | Ground | Always | Below 1 Ω | - |
| G16-1 (+B) - G16-10 (E) | Input | P - BR | +B power supply | Always | 11 to 14 V | - |
| G17-33 (CUTB) - G16-10 (E) | Input | W - BR | Dark current cut pin* | Always | 11 to 14 V | - |
*: In order to prevent the vehicle battery from being depleted when the vehicle is shipped long distances, a fuse that cuts unnecessary electrical load while the vehicle is being shipped is set in the circuit. If the fuse is removed, the circuit becomes open. If the fuse that is between the vehicle battery and terminal CUTB is removed and the circuit is open, the certification ECU (smart key ECU assembly) changes to a certain control mode.
Connect the G16 and G17 certification ECU (smart key ECU assembly) connectors.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|---|
|
*1: for LHD *2: for RHD |
||||||
| G16-21 (ACCD) - G16-10 (E) | Output | B - BR | ACC signal | Engine switch off → Engine switch on (ACC) | 1 V or less → 8.5 V or higher | - |
| G16-20 (IG1D) - G16-10 (E) | Output | L - BR | IG1 signal | Engine switch on (ACC) → Engine switch on (IG) | 1 V or less → 9 V or higher | - |
| G17-9 (CLG5) - G16-10 (E) | Input/Output | R - BR | Output to driver door electrical key antenna
(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area) |
Procedure:
1.
Engine switch off 2.
All doors closed |
Not pulse generation | Overhead + Driver Side (key diagnostic mode) |
| Procedure:
1.
Engine switch off 2.
All doors closed 3.
While carrying the electrical key transmitter sub-assembly, press the trigger switch on the front door outside handle assembly (for Driver Door). |
Pulse generation (See waveform 1) | |||||
| G17-25 (CG5B) - G16-10 (E) | Input/Output | W - BR | Output to driver door electrical key antenna
(terminal on opposite side of component from CLG5 output terminal) |
Procedure:
1.
Engine switch off 2.
All doors closed |
Not pulse generation | Overhead + Driver Side (key diagnostic mode) |
| Procedure:
1.
Engine switch off 2.
All doors closed 3.
While carrying the electrical key transmitter sub-assembly, press the trigger switch on the front door outside handle assembly (for Driver Door). |
Pulse generation (See waveform 1) | |||||
| G17-26 (CLG6) - G16-10 (E) | Input/Output | Y - BR | Output to front passenger door electrical key antenna
(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area) |
Procedure:
1.
Engine switch off 2.
All doors closed |
Not pulse generation | Overhead + Passenger Side (key diagnostic mode) |
| Procedure:
1.
Engine switch off 2.
All doors closed 3.
While carrying the electrical key transmitter sub-assembly, press the trigger switch on the front door outside handle assembly (for Front Passenger Door). |
Pulse generation (See waveform 2) | |||||
| G17-27 (CG6B) - G16-10 (E) | Input/Output | B - BR | Output to front passenger door electrical key antenna
(terminal on opposite side of component from CLG6 output terminal) |
Procedure:
1.
Engine switch off 2.
All doors closed |
Not pulse generation | Overhead + Passenger Side (key diagnostic mode) |
| Procedure:
1.
Engine switch off 2.
All doors closed 3.
While carrying the electrical key transmitter sub-assembly, press the trigger switch on the front door outside handle assembly (for Front Passenger Door). |
Pulse generation (See waveform 2) | |||||
| G17-8 (CLG8) - G16-10 (E) | Input/Output | LG - BR | Output to No. 2 indoor electrical key antenna assembly (back door)
(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area) |
Procedure:
1.
Engine switch off 2.
All doors closed |
Not pulse generation | Overhead + Back Door (key diagnostic mode) |
| Procedure:
1.
Engine switch off 2.
All doors closed 3.
Back door opener switch assembly off → on. |
Pulse generation (See waveform 3) | |||||
| G17-24 (CG8B) - G16-10 (E) | Input/Output | P - BR | Output to No. 2 indoor electrical key antenna assembly (back door)
(terminal on opposite side of component from CLG8 output terminal) |
Procedure:
1.
Engine switch off 2.
All doors closed |
Not pulse generation | Overhead + Back Door (key diagnostic mode) |
| Procedure:
1.
Engine switch off 2.
All doors closed 3.
Back door opener switch assembly off → on. |
Pulse generation (See waveform 3) | |||||
| G16-4 (TSW1) - G16-10 (E) | Input | P - BR*1
L - BR*2 |
Driver door trigger switch signal input sends signals from trigger switch on front door outside handle assembly (for Driver Door) to certification ECU (smart key ECU assembly).
Certification ECU (smart key ECU assembly) sends 12 V pulse waveform every 20 ms. from terminal TSW. When trigger switch is pressed, the pulse is grounded. |
Procedure:
1.
Engine switch off 2.
All doors closed 3.
Driver door trigger switch not pressed → pressed |
9.5 to 16 V → Below 1.5 V | D-Door Trigger Switch |
| G16-12 (TSW2) - G16-10 (E) | Input | G - BR*1
R - BR*2 |
Passenger door trigger switch signal input sends signals from trigger switch on front door outside handle assembly (for Front Passenger Door) to certification ECU (smart key ECU assembly).
Certification ECU (smart key ECU assembly) sends 12 V pulse waveform every 20 ms. from terminal TSW. When trigger switch is pressed, the pulse is grounded. |
Procedure:
1.
Engine switch off 2.
All doors closed 3.
Passenger door trigger switch not pressed → pressed |
9.5 to 16 V → Below 1.5 V | P-Door Trigger Switch |
| G16-14 (TSW5) - G16-10 (E) | Input | V - BR | Back door opener switch assembly (unlock switch) signal input | Back door opener switch assembly (open switch) off → on | 4.5 V or higher → Below 1.5 V | Tr/B-Door Unlock SW |
| G16-23 (TSW6) - G16-10 (E) | Input | BE - BR | Back door opener switch assembly (lock switch) signal input | Back door opener switch assembly (lock switch) off → on | 4.5 V or higher → Below 1.5 V | Tr/B-Door Lock SW |
| G17-31 (CLG1) - G16-10 (E) | Input/Output | Y - BR | Output to No. 1 indoor electrical key antenna assembly (front floor) | Procedure:
1.
All doors closed 2.
Engine switch off 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
Door is open 5.
Door is closed 6.
Within 30 seconds |
Pulse generation (See waveform 4) | Overhead + Room (key diagnostic mode) |
| G17-30 (CG1B) - G16-10 (E) | Input/Output | L - BR | Output to No. 1 indoor electrical key antenna assembly (front floor) (terminal on opposite side of component from CLG1 output terminal) | Procedure:
1.
All doors closed 2.
Engine switch off 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
Door is open 5.
Door is closed 6.
Within 30 seconds |
Pulse generation (See waveform 4) | Overhead + Room (key diagnostic mode) |
| G17-6 (CLG2) - G16-10 (E) | Input/Output | W - BR | Output to No. 2 indoor electrical key antenna assembly (rear floor) | Procedure:
1.
All doors closed 2.
Engine switch off 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
Door is open 5.
Door is closed 6.
Within 30 seconds |
Pulse generation (See waveform 4) | Overhead + Room2 (key diagnostic mode) |
| G17-23 (CG2B) - G16-10 (E) | Input/Output | B - BR | Output to No. 2 indoor electrical key antenna assembly (rear floor) (terminal on opposite side of component from CLG2 output terminal) | Procedure:
1.
All doors closed 2.
Engine switch off 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
Door is open 5.
Door is closed 6.
Within 30 seconds |
Pulse generation (See waveform 4) | Overhead + Room2 (key diagnostic mode) |
| G17-28 (CLG7) - G16-10 (E) | Input/Output | R - BR | Output to No. 2 indoor electrical key antenna assembly (inside luggage) | Procedure:
1.
All doors closed 2.
Engine switch off 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
Door is open 5.
Door is closed 6.
Within 30 seconds |
Pulse generation (See waveform 4) | Overhead + Room3 (key diagnostic mode) |
| G17-29 (CG7B) - G16-10 (E) | Input/Output | G - BR | Output to No. 2 indoor electrical key antenna assembly (inside luggage) (terminal on opposite side of component from CLG7 output terminal) | Procedure:
1.
All doors closed 2.
Engine switch off 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
Door is open 5.
Door is closed 6.
Within 30 seconds |
Pulse generation (See waveform 4) | Overhead + Room3 (key diagnostic mode) |
| G16-9 (LSWP) - G16-10 (E) | Input | L - BR | Except driver door unlock detection switch input | Procedure:
1.
Engine switch off 2.
All doors closed 3.
Lock button of electrical key transmitter sub-assembly not pressed |
Below 1 V | - |
| Procedure:
1.
Engine switch off 2.
All doors closed 3.
Lock button of electrical key transmitter sub-assembly pressed |
8.5 V or higher | |||||
| G17-3 (RCO) - G16-10 (E) | Output | G - BR | Output to door control receiver
(Power supply for door control receiver. Certification ECU (smart key ECU assembly) outputs 5 V when receiver starts operating.) |
Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed |
Pulse generation (See waveform 5) | - |
| G17-22 (RDAS) - G16-10 (E) | Input | L - BR | Door control receiver verifies data received from electrical key transmitter sub-assembly. Door control receiver sends data to ECU and intermittently grounds 12 V signal from certification ECU (smart key ECU assembly). | Proceed:
1.
Engine switch off 2.
All doors locked 3.
Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed |
Pulse generation (See waveform 6) | - |
| G17-21 (CSEL) - G16-10 (E) | Output | P - BR | Communication channel switching circuit | Procedure:
1.
Engine switch off 2.
All doors closed |
Pulse generation (See waveform 7) | Key diagnostic mode |
| G16-2 (BZR) - G16-10 (E) | Output | SB - BR | Wireless door lock buzzer signal | Wireless door lock buzzer on | Pulse generation | - |
| G17-13 (RDA3) - G16-10 (E) | Output | W - BR | Signal output to instrument panel junction block assembly (body ECU) | Procedure:
1.
Engine switch off 2.
All doors closed 3.
Lock button of electrical key transmitter sub-assembly not pressed |
11 to 14 V | - |
| Procedure:
1.
Engine switch off 2.
All doors closed 3.
Lock button of electrical key transmitter sub-assembly pressed |
Pulse generation | |||||
| G17-36 (PRG3) - G16-10 (E) | Input | V - BR | Signal input from instrument panel junction block assembly (body ECU) | Procedure:
1.
Engine switch off 2.
All doors closed 3.
10 seconds elapsed after all doors locked 4.
Electrical key transmitter sub-assembly unlock switch not pressed |
11 to 14 V | - |
| Procedure:
1.
Engine switch off 2.
All doors closed 3.
10 seconds elapsed after all doors locked 4.
Electrical key transmitter sub-assembly unlock switch pressed |
Pulse generation | |||||
| *a | Trigger switch ON |
Using an oscilloscope, check waveform 1.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | ·
G17-9 (CLG5) - G16-10 (E) ·
G17-25 (CG5B) - G16-10 (E) |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Procedure:
1.
Engine switch off 2.
All doors closed 3.
While carrying the electrical key transmitter sub-assembly, press the trigger switch on the front door outside handle assembly (for Driver Door). |
| *a | Trigger switch ON |
Using an oscilloscope, check waveform 2.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | ·
G17-26 (CLG6) - G16-10 (E) ·
G17-27 (CG6B) - G16-10 (E) |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Procedure:
1.
Engine switch off 2.
All doors closed 3.
While carrying the electrical key transmitter sub-assembly, press the trigger switch on the front door outside handle assembly (for Front Passenger Door). |
| *a | Back door opener switch assembly ON |
Using an oscilloscope, check waveform 3.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | ·
G17-8 (CLG8) - G16-10 (E) ·
G17-24 (CG8B) - G16-10 (E) |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Procedure:
1.
Engine switch off 2.
All doors closed 3.
Back door opener switch assembly off → on |
| *a | Door open |
| *b | After approximately 30 seconds from when the door is closed |
Using an oscilloscope, check waveform 4.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | ·
G17-31 (CLG1) - G16-10 (E) ·
G17-30 (CG1B) - G16-10 (E) ·
G17-6 (CLG2) - G16-10 (E) ·
G17-23 (CG2B) - G16-10 (E) ·
G17-28 (CLG7) - G16-10 (E) ·
G17-29 (CG7B) - G16-10 (E) |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Procedure:
1.
All doors closed 2.
Engine switch off 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
Door is open 5.
Door is closed 6.
Within 30 seconds |
| *a | Before lock or unlock button of electrical key transmitter sub-assembly pressed |
| *b | After lock or unlock button of electrical key transmitter sub-assembly pressed |
Using an oscilloscope, check waveform 5.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | G17-3 (RCO) - G16-10 (E) |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed |
| *a | Before lock or unlock button of electrical key transmitter sub-assembly pressed |
| *b | After lock or unlock button of electrical key transmitter sub-assembly pressed |
Using an oscilloscope, check waveform 6.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | G17-22 (RDAS) - G16-10 (E) |
| Tool Setting | 5 V/DIV., 500 ms./DIV. |
| Condition | Procedure:
1.
Engine switch off 2.
All doors locked 3.
Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed |
Using an oscilloscope, check waveform 7.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Item | Content |
|---|---|
| Tester Connection | G17-21 (CSEL) - G16-10 (E) |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Procedure:
1.
Engine switch off 2.
All doors closed |
CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (BODY ECU)
| *A | for LHD | *B | for RHD |
| *1 | Instrument Panel Junction Block Assembly | - | - |
| *1 | Body ECU | - | - |
Remove the body ECU from the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connector disconnected.
| Tester Connection | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|---|
| A-1 (GND) - Body ground | - | - | Ground | Always | Below 1 Ω |
| A-6 (BECU) - Body ground | Input | - | Battery power supply (for CPU) | Always | 11 to 14 V |
| A-7 (IG) - Body ground | Input | - | Engine switch power supply | Engine switch on (IG) → off | 11 to 14 V → Below 1 V |
Install the body ECU to the instrument panel junction block assembly.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|---|
|
*1: w/ Door Control Battery *2: w/o Door Control Battery *3: w/o Double Locking *4: w/ Double Locking |
|||||
| 2N-2 (ACT+) - Body ground | Output | LG - Body ground*1
LA-B - Body ground*2 |
Door lock motor lock drive output (all doors) | Door control switch (power window regulator master switch assembly) or driver door key cylinder off | Below 1 V |
| Door control switch (power window regulator master switch assembly) or driver door key cylinder locked | 11 to 14 V | ||||
| 2N-3 (ACT-) - Body ground | Output | GR - Body ground*1
LA-W - Body ground*2 |
Door lock motor unlock drive output (all doors)*3
Door lock motor unlock drive output (except driver door)*4 |
Door control switch (power window regulator master switch assembly) or driver door key cylinder off | Below 1 V |
| Door control switch (power window regulator master switch assembly) or driver door key cylinder unlocked | 11 to 14 V | ||||
| 2J-4 (ACTD) - Body ground*4 | Output | Y - Body ground | Door lock motor unlock drive output (driver door) | Door control switch (power window regulator master switch assembly) or driver door key cylinder off | Below 1 V |
| Door control switch (power window regulator master switch assembly) or driver door key cylinder unlocked | 11 to 14 V | ||||
| 2Q-1 (DCTY) - Body ground | Input | B - Body ground | Front door (for Driver Door) courtesy light switch input | Front door (for Driver Door) open | Below 1 V |
| Front door (for Driver Door) closed | Pulse generation | ||||
| 2Q-2 (ACTY) - Body ground | Input | Y - Body ground | All door courtesy light switches input except driver door | One or more doors are open except driver door | Below 1 V |
| All doors are closed except driver door | Pulse generation | ||||
| 2L-4 (DCTY) - Body ground | Input | R - Body ground | Front door (for Driver Door) courtesy light switch input | Front door (for Driver Door) open | Below 1 V |
| Front door (for Driver Door) closed | Pulse generation | ||||
| G33-2 (LSWP) - Body ground | Input | Y - Body ground | Except front door (for Driver Door) unlock detection switch input | Except front door (for Driver Door) unlocked | Below 1 V |
| Except front door (for Driver Door) locked | Pulse generation | ||||
| G33-6 (HAZ) - Body ground | Output | SB - Body ground | Hazard warning signal output | Answer-back off | 11 to 14 V |
| Answer-back on | Below 1 V | ||||
| G33-9 (PRG) - Body ground | Output | V - Body ground | Signal output to certification ECU (smart key ECU assembly) | Procedure:
1.
Engine switch off 2.
All doors locked 3.
10 seconds elapsed after all doors locked 4.
Electrical key transmitter sub-assembly unlock switch not pressed |
11 to 14 V |
Procedure:
1.
Engine switch off 2.
All doors locked 3.
10 seconds elapsed after all doors locked 4.
Electrical key transmitter sub-assembly unlock switch pressed |
Pulse generation | ||||
| G33-14 (PCTY) - Body ground | Input | LG - Body ground | Except front door (for Driver Door) courtesy light switch input | Except front door (for Driver Door) open | Below 1 V |
| Except front door (for Driver Door) closed | Pulse generation | ||||
| G33-15 (LSWD) - Body ground | Input | R - Body ground | Front door (for Driver Door) unlock detection switch input | Front door (for Driver Door) unlocked | Below 1 V |
| Front door (for Driver Door) locked | Pulse generation | ||||
| G33-16 (RDA) - Body ground | Input | W - Body ground | Signal input from certification ECU (smart key ECU assembly) | Procedure:
1.
Engine switch off 2.
All doors locked 3.
10 seconds elapsed after all doors locked 4.
Electrical key transmitter sub-assembly unlock switch not pressed |
11 to 14 V |
Procedure:
1.
Engine switch off 2.
All doors locked 3.
10 seconds elapsed after all doors locked 4.
Electrical key transmitter sub-assembly unlock switch pressed |
Pulse generation | ||||
CHECK COMBINATION METER ASSEMBLY
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU