Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY(for DANA Made w/ Differential Lock) › from 2016.01
RM3270E _52 Drivetrain _041686 AXLE AND DIFFERENTIAL _0243213 REAR DIFFERENTIAL CARRIER ASSEMBLY(for DANA Made w/ Differential Lock) A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER ASSEMBLY(for DANA Made w/ Differential Lock)  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

The following procedures are for BD22 (w/ Differential Lock).


PROCEDURE

Hide 41110 1.SECURE REAR DIFFERENTIAL CARRIER ASSEMBLY

a.
C325515

Secure the rear differential carrier assembly.


Hide 41204 2.INSPECT REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
C325516C01
2.573,1.906 2.885,2.104 0.313,0.198 10 false *a
*a 36 mm (1.42 in.)


Using a dial indicator, measure the runout of the companion flange vertically and laterally.

Maximum Runout:
Runout Maximum
Vertical runout 0.10 mm (0.00394 in.)
Lateral runout 0.10 mm (0.00394 in.)


If the runout is more than the maximum, replace the companion flange.


Hide 3.INSPECT DIFFERENTIAL RING GEAR BACKLASH

a.
C325518

Using a dial indicator, measure the backlash of the differential ring gear.

Standard backlash:

0.13 to 0.20 mm (0.00512 to 0.00787 in.)


If the backlash is not within the specification, adjust the side bearing preload or perform repairs as necessary.

HINT:

Perform the measurement at 3 or more positions around the circumference of the ring gear.




Hide 4.INSPECT TOTAL PRELOAD

a.
C326871

Using a torque wrench, measure the preload with the teeth of the differential drive pinion and differential ring gear in contact.

If the result is not as specified, adjust the preload.

Standard Total Preload:
Reduction Ratio Specified Condition
3.583 2.27 to 4.30 N*m (24 to 43 kgf*cm, 21 to 38 in.*lbf)
3.909 2.25 to 4.24 N*m (23 to 43 kgf*cm, 20 to 37 in.*lbf)
4.100 2.24 to 4.22 N*m (23 to 43 kgf*cm, 20 to 37 in.*lbf)
4.300 2.23 to 4.19 N*m (23 to 42 kgf*cm, 20 to 37 in.*lbf)
4.555 2.21 to 4.16 N*m (23 to 42 kgf*cm, 20 to 36 in.*lbf)



Hide 41204B 5.REMOVE REAR DRIVE PINION NUT

a.
C325761N01
1.24,0.521 1.24,0.208 1.24,0.208 1.781,0.208 false 1.823,0.125 2.281,0.323 0.458,0.198 10 false SST

Using a chisel and hammer, stake the rear drive pinion nut.

SST
09930-00010  (09931-00010, 09931-00020)


b.
C325762C01
2.167,1.5 2.833,1.5 false 0.792,1.271 1.104,1.469 0.313,0.198 10 false *a 2.917,1.406 3.375,1.604 0.458,0.198 10 false SST 2.146,1.948 2.458,2.146 0.313,0.198 10 false *b
*a Turn
*b Hold


Using SST to hold the companion flange in place, remove the rear drive pinion nut.

SST
09330-00021  (09330-00030)


Hide 41204 6.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

a.
C349556C01
0.677,0.542 1.073,0.542 1.073,0.542 1.302,1.281 false 2.875,0.542 3.188,0.74 0.313,0.198 10 false *a 0.323,1.208 0.635,1.406 0.313,0.198 10 false *b 0.375,0.469 0.833,0.667 0.458,0.198 10 false SST
*a Turn
*b Hold


Using SST, remove the rear drive pinion companion flange sub-assembly with dust deflector.

SST
09950-40011  (09951-04010, 09953-04020, 09954-04010, 09955-04061)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



Hide 41201C 7.REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL

a.
C325764C01
2.979,1.542 2.75,1.542 2.75,1.542 2.74,0.885 true 2.875,1.958 2.594,1.958 2.594,1.958 2.594,0.885 true 0.594,2.469 0.594,2.177 0.594,2.177 1.021,2.177 false 3.031,1.458 3.344,1.656 0.313,0.198 10 false *1 2.917,1.875 3.229,2.073 0.313,0.198 10 false *2 0.49,2.49 0.948,2.688 0.458,0.198 10 false SST
*1 Rear Differential Carrier Oil Seal
*2 Rear Differential Drive Pinion Oil Slinger


Using SST, remove the rear differential carrier oil seal.

SST
09308-10010  


Hide 41214 8.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

a.
C325765

Remove the rear differential drive pinion oil slinger from the differential drive pinion.


Hide 9.REMOVE WIRING HARNESS CONNECTOR

a.
C349557

Remove the bolt and wiring harness connector.


b.
C326172

Disconnect the connector.


Hide 10.REMOVE DIFFERENTIAL BEARING CAP

a.
C325524C01
0.406,1.208 1.583,1.208 true 0.563,1.208 0.563,0.854 0.563,0.854 1.167,0.854 true 0.24,1.115 0.552,1.313 0.313,0.198 10 false *a
*a Matchmark


Place matchmarks on the differential bearing cap and differential carrier.


b.

Remove the 4 bolts and 2 differential bearing caps.


c.

Remove the 2 plate washers.

C349558C01
0.75,0.063 1.063,0.26 0.313,0.198 10 false *a 3.896,0.063 4.208,0.26 0.313,0.198 10 false *b
*a LH Side (Ring Gear Side) *b RH Side (Differential Lock Coil Side)


HINT:
·

Put identification marks on the plate washers to show the location for installation (LH side (ring gear side) or RH side (differential lock coil side)), or keep them separate so that they can be distinguished.

·

Measure the thickness of each plate washers and note it.




Hide 41303E 11.REMOVE ELECTRONIC DIFFERENTIAL LOCK CASE SUB-ASSEMBLY

a.
C325526

Remove the electronic differential lock case sub-assembly from the differential carrier.

HINT:

Tag the 2 rear differential case bearings (outer) so that they can be reinstalled in the correct locations.



Hide 84222 12.REMOVE NO. 1 TRANSFER INDICATOR SWITCH (REAR DIFFERENTIAL LOCK POSITION SWITCH)

a.
C349559

Remove the bolt and No. 1 transfer indicator switch (rear differential lock position switch).


Hide 13.REMOVE DIFFERENTIAL DRIVE PINION

a.
C325766

Using a press, remove the differential drive pinion with rear differential drive pinion bearing spacer from the differential carrier.

NOTICE:

Do not drop the differential drive pinion.



Hide 41231 14.REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

a.
C325767

Remove the rear differential drive pinion bearing spacer from the differential drive pinion.


Hide 41201A 15.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C325527N01
1.531,0.896 1.406,0.167 1.406,0.167 1.021,0.167 false 0.677,0.083 1.135,0.281 0.458,0.198 10 false SST

Using SST and a press, press out the rear drive pinion rear tapered roller bearing (inner) from the differential drive pinion.

SST
09555-55010  

NOTICE:

Do not drop the differential drive pinion.


HINT:

If the differential drive pinion or differential ring gear is damaged, replace them as a set.



Hide 41201B 16.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C325523

Remove the rear drive pinion front tapered roller bearing (inner) from the differential carrier.


Hide 41201B 17.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C325528C01
0.323,0.844 0.323,0.594 0.323,0.594 0.656,0.594 false 2.146,1.719 2.146,1.25 2.146,1.25 2.448,0.917 true 0.219,0.865 0.677,1.063 0.458,0.198 10 false SST 2.094,1.76 2.406,1.958 0.313,0.198 10 false *1
*1 Rear Drive Pinion Front Tapered Roller Bearing (Outer)


Using SST, remove the rear drive pinion front tapered roller bearing (outer) from the differential carrier.

SST
09308-00010  


Hide 41115 18.REMOVE DIFFERENTIAL OIL STORAGE RING

a.
C325529C01
1.052,3.167 1.958,3.167 1.958,3.167 2.271,2.833 true 0.771,1.01 0.927,1.688 0.927,1.688 1.24,1.688 true 0.729,3.073 1.188,3.271 0.458,0.198 10 false SST 1.302,1.604 1.615,1.802 0.313,0.198 10 false *1
*1 Differential Oil Storage Ring


Using SST and a hammer, tap out the differential oil storage ring from the differential carrier.

SST
09316-60011  (09316-00011)


Hide 41201A 19.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C325530

Using a brass bar and hammer, tap out the rear drive pinion rear tapered roller bearing (outer) and adjusting shim from the differential carrier.

If the bearing is damaged during removal, replace it.


Hide 20.REMOVE DIFFERENTIAL RING GEAR

a.
C325531C01
2.323,1.031 2.844,1.031 true 2.396,1.094 2.719,1.094 2.719,1.094 2.719,1.042 true 2.906,0.938 3.219,1.135 0.313,0.198 10 false *a
*a Matchmark


Place matchmarks on the differential ring gear and differential case.


b.

Remove the 12 differential ring gear set bolts.


c.
C325532

Using a plastic-faced hammer, tap on the differential ring gear to remove it from the differential case.

NOTICE:

Do not damage the position plate when removing the ring gear.



Hide 21.INSPECT DIFFERENTIAL CASE ASSEMBLY RUNOUT

HINT:

If the ring gear runout is within the specified value (refer to the "Inspect Runout of Differential Ring Gear" procedure above), skip this step.


a.

Install the rear differential case bearings (outer) to the electronic differential lock case sub-assembly.


b.

Install the electronic differential lock case sub-assembly to the differential carrier.


c.

Install the 2 plate washers.


d.

Install the 2 differential bearing caps to the differential carrier with the 4 bolts.

Torque:
140 N*m (1428 kgf*cm, 103 ft.*lbf)


e.
C325533C01
0.229,1.271 0.542,1.469 0.313,0.198 10 false *a
*a 92 mm (3.62 in.)


Using a dial indicator, measure the electronic differential case runout.

Maximum runout:

0.07 mm (0.00276 in.)



f.

Remove the 4 bolts and 2 differential bearing caps.


g.

Remove the 2 plate washers.


h.

Remove the electronic differential lock case sub-assembly.


i.

Remove the rear differential case bearings (outer).


Hide 41301A 22.REMOVE REAR DIFFERENTIAL CASE BEARING

a.
C325535C01
0.802,0.688 0.802,0.25 0.802,0.25 0.542,0.25 false 2.188,0.229 2.5,0.427 0.313,0.198 10 false *a 0.063,0.865 0.375,1.063 0.313,0.198 10 false *b 0.24,0.177 0.583,0.375 0.344,0.198 10 false SST
*a Turn
*b Hold


for LH Side (Ring Gear Side):

i.

Using SST, remove the rear differential case bearing (inner) from the electronic differential lock case sub-assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
09950-60010  (09951-00640)

HINT:

Do not remove the case bearings when not replacing the electronic differential lock case sub-assembly.




b.

for RH Side (Differential Lock Coil Side):

i.
C325534C01
0.708,0.833 0.708,0.323 0.708,0.323 0.479,0.323 false 2.177,0.333 2.49,0.531 0.313,0.198 10 false *a 0.063,1 0.375,1.198 0.313,0.198 10 false *b 0.177,0.25 0.635,0.448 0.458,0.198 10 false SST
*a Turn
*b Hold


Using SST, remove the rear differential case bearing (inner) from the electronic differential lock case sub-assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04011, 09957-04010, 09958-04011)
09950-60010  (09951-00640)

HINT:

Do not remove the case bearings when not replacing the electronic differential lock case sub-assembly.




Hide 41367 23.REMOVE DIFFERENTIAL SOLENOID WASHER

a.
C325536N01
1.042,0.5 0.865,0.323 0.865,0.323 0.563,0.323 false 0.24,0.26 0.698,0.458 0.458,0.198 10 false SST

Tighten the 2 SST nuts evenly and remove the differential solenoid washer from the electronic differential lock case sub-assembly.

SST
09555-55010  


Hide 41451H 24.REMOVE DIFFERENTIAL LOCK COIL

a.
C325537

Remove the differential lock coil from the electronic differential lock case sub-assembly.


Hide 25.REMOVE DIFFERENTIAL LOCK PLUNGER

a.
C325540

Remove the differential lock plunger from the rear differential case sub-assembly.


Hide 41302 26.DISASSEMBLE REAR DIFFERENTIAL CASE SUB-ASSEMBLY

a.
C325541

Remove the 2 screws.


b.
C325542C01
0.365,0.698 0.365,0.396 0.365,0.396 0.823,0.396 false 0.281,2.563 0.281,2.031 0.281,2.031 0.604,2.031 false 0.302,0.74 0.615,0.938 0.313,0.198 10 false *1 0.219,2.615 0.531,2.813 0.313,0.198 10 false *2
*1 Differential Case LH
*2 Differential Case RH


Remove the differential case LH from the differential case RH.


c.
C325543

Remove the differential side gear and rear No. 1 differential side gear thrust washer from the differential case LH.


d.
C325544

Remove the 2 rear differential pinion shaft pins.


e.
C325545C02
1.677,4.396 2,4.396 2,4.396 2.323,4.135 false 0.865,1.948 1.375,1.948 false 1.833,1.365 2.719,1.365 false 0.906,0.385 0.906,0.135 0.906,0.135 1.208,0.135 false 0.583,4.104 0.844,4.104 0.844,4.104 0.844,3.604 false 1.771,2.573 2.583,2.573 false 2.917,3.49 2.646,3.49 2.646,3.49 2.646,3.125 false 0.281,1.729 0.281,1.396 0.281,1.396 0.521,1.396 false 1.281,0.667 1.281,0.406 1.281,0.406 1.542,0.406 false 2.125,0.813 2.125,0.198 2.125,0.198 2.448,0.198 false 0.458,0.865 0.656,0.865 0.656,0.865 0.906,1.146 false 2.24,1.677 2.75,1.677 false 2.615,0.875 2.885,0.875 false 2.521,1.958 2.865,1.958 false 1.771,2.26 2.042,2.26 false 2.781,1.281 3.094,1.479 0.313,0.198 10 false *1 2.656,2.469 2.969,2.667 0.313,0.198 10 false *2 2.115,2.177 2.427,2.375 0.313,0.198 10 false *3 0.385,4.021 0.698,4.219 0.313,0.198 10 false *7 0.688,1.875 1,2.073 0.313,0.198 10 false *8 2.99,3.417 3.302,3.615 0.313,0.198 10 false *7 1.49,4.313 1.802,4.51 0.313,0.198 10 false *6 1.604,0.302 1.917,0.5 0.313,0.198 10 false *4 2.51,0.104 2.823,0.302 0.313,0.198 10 false *4 2.813,1.583 3.125,1.781 0.313,0.198 10 false *4 0.271,0.781 0.583,0.979 0.313,0.198 10 false *4 2.938,1.875 3.25,2.073 0.313,0.198 10 false *5 1.281,0.052 1.594,0.25 0.313,0.198 10 false *5 2.938,0.792 3.25,0.99 0.313,0.198 10 false *5 0.219,1.792 0.531,1.99 0.313,0.198 10 false *5
*1 Differential Side Gear (Dog Clutch)
*2 Rear No. 2 Differential Side Gear Thrust Washer
*3 Rear No. 3 Differential Side Gear Thrust Washer
*4 Differential Pinion
*5 Rear Differential Pinion Thrust Washer
*6 Rear Differential Pinion Shaft
*7 Rear No. 2 Differential Pinion Shaft
*8 Differential Lock Spring


Remove the following parts from the differential case RH.

1.

Differential side gear (Dog clutch)

2.

Rear No. 2 differential side gear thrust washer

3.

Rear No. 3 differential side gear thrust washer

4.

Differential pinion (4 pieces)

5.

Rear differential pinion thrust washer (4 pieces)

6.

Rear differential pinion shaft

7.

Rear No. 2 differential pinion shaft (2 pieces)

8.

Differential lock spring



Hide 41474A 27.REMOVE DIFFERENTIAL LOCK POSITION PLATE

a.
C325538

Using a T25 ''TORX'' socket wrench, remove the 3 screws from the differential lock position plate.


b.
C325539C01
2.229,0.542 2.594,0.542 false 2.031,2.948 2.615,2.948 false 2.646,0.458 2.958,0.656 0.313,0.198 10 false *1 2.646,2.875 2.958,3.073 0.313,0.198 10 false *2
*1 Differential Lock Position Plate
*2 Differential Lock Cam Ring


Remove the differential lock position plate from the differential case RH.


Hide 41433A 28.REMOVE DIFFERENTIAL LOCK CAM RING

a.

Remove the differential lock cam ring from the differential case RH.


Hide 29.INSPECT DIFFERENTIAL GEAR KIT

a.

Check that the differential pinion and differential side gear are not damaged.

If the differential pinion or differential side gear is damaged, replace the differential gear kit.


Hide 30.INSPECT DIFFERENTIAL CASE

a.

Check that the differential case is not damaged.

If the differential case is damaged, replace it.