Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY(for DANA Made w/o Differential Lock) › from 2016.01
RM3270E _52 Drivetrain _041686 AXLE AND DIFFERENTIAL _0243214 REAR DIFFERENTIAL CARRIER ASSEMBLY(for DANA Made w/o Differential Lock) A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER ASSEMBLY(for DANA Made w/o Differential Lock)  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

The following procedures are for BD22 (w/o Differential Lock).


PROCEDURE

Hide 41110 1.SECURE REAR DIFFERENTIAL CARRIER ASSEMBLY

a.
C325515

Secure the rear differential carrier assembly.


Hide 41204 2.INSPECT REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
C325516C01
2.573,1.906 2.885,2.104 0.313,0.198 10 false *a
*a 36 mm (1.42 in.)


Using a dial indicator, measure the runout of the companion flange vertically and laterally.

Maximum Runout:
Runout Maximum
Vertical runout 0.10 mm (0.00394 in.)
Lateral runout 0.10 mm (0.00394 in.)


If the runout is more than the maximum, replace the companion flange.


Hide 3.INSPECT DIFFERENTIAL RING GEAR BACKLASH

a.
C326622

Using a dial indicator, measure the backlash of the differential ring gear.

Standard backlash:

0.13 to 0.20 mm (0.00512 to 0.00787 in.)


If the backlash is not within the specification, adjust the side bearing preload or perform repairs as necessary.

HINT:

Perform the measurement at 3 or more positions around the circumference of the ring gear.




Hide 4.INSPECT TOTAL PRELOAD

a.
C326871

Using a torque wrench, measure the preload with the teeth of the differential drive pinion and differential ring gear in contact.

Standard Total Preload:
Reduction Ratio Specified Condition
3.909 2.25 to 4.24 N*m (23 to 43 kgf*cm, 20 to 37 in.*lbf)
4.300 2.23 to 4.19 N*m (23 to 42 kgf*cm, 20 to 37 in.*lbf)
4.555 2.21 to 4.16 N*m (23 to 42 kgf*cm, 20 to 36 in.*lbf)


If the result is not as specified, adjust the preload.


Hide 41204B 5.REMOVE REAR DRIVE PINION NUT

a.
C325761N01
1.24,0.521 1.24,0.208 1.24,0.208 1.781,0.208 false 1.823,0.125 2.281,0.323 0.458,0.198 10 false SST

Using a chisel and hammer, stake the rear drive pinion nut.

SST
09930-00010  (09931-00010, 09931-00020)


b.
C325762C01
2.167,1.5 2.833,1.5 false 0.792,1.271 1.104,1.469 0.313,0.198 10 false *a 2.917,1.406 3.375,1.604 0.458,0.198 10 false SST 2.146,1.948 2.458,2.146 0.313,0.198 10 false *b
*a Turn
*b Hold


Using SST to hold the rear drive pinion companion flange sub-assembly with dust deflector in place, remove the rear drive pinion nut.

SST
09330-00021  (09330-00030)


Hide 41204 6.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

a.
C349556C01
0.677,0.542 1.073,0.542 1.073,0.542 1.302,1.281 false 2.875,0.542 3.188,0.74 0.313,0.198 10 false *a 0.323,1.208 0.635,1.406 0.313,0.198 10 false *b 0.375,0.469 0.833,0.667 0.458,0.198 10 false SST
*a Turn
*b Hold


Using SST, remove the rear drive pinion companion flange sub-assembly with dust deflector.

SST
09950-40011  (09951-04010, 09953-04020, 09954-04010, 09955-04061)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



Hide 41201C 7.REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL

a.
C325764C01
2.979,1.542 2.75,1.542 2.75,1.542 2.74,0.885 true 2.875,1.958 2.594,1.958 2.594,1.958 2.594,0.885 true 0.594,2.469 0.594,2.177 0.594,2.177 1.021,2.177 false 3.031,1.458 3.344,1.656 0.313,0.198 10 false *1 2.917,1.875 3.229,2.073 0.313,0.198 10 false *2 0.49,2.49 0.948,2.688 0.458,0.198 10 false SST
*1 Rear Differential Carrier Oil Seal
*2 Rear Differential Drive Pinion Oil Slinger


Using SST, remove the rear differential carrier oil seal.

SST
09308-10010  


Hide 41214 8.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

a.
C325765

Remove the rear differential drive pinion oil slinger from the differential drive pinion.


Hide 9.REMOVE DIFFERENTIAL BEARING CAP

a.
C326623C01
0.427,1.208 1.583,1.208 true 0.75,1.198 0.74,0.844 0.74,0.844 1.167,0.844 true 0.24,1.104 0.552,1.302 0.313,0.198 10 false *a
*a Matchmark


Place matchmarks on the differential bearing cap and differential carrier.


b.

Remove the 4 bolts and 2 differential bearing caps.


c.

Remove the 2 plate washers.

C349562C01
0.76,0.063 1.073,0.26 0.313,0.198 10 false *a 3.917,0.063 4.229,0.26 0.313,0.198 10 false *b
*a LH Side (Back Side) *b RH Side (Teeth Side)


HINT:
·

Put identification marks on the plate washers to show the location for installation (LH side (back side) or RH side (teeth side)), or keep them separate so that they can be distinguished.

·

Measure the thickness of each plate washers and note it.




Hide 10.REMOVE DIFFERENTIAL CASE ASSEMBLY

a.
C326625

Remove the differential case assembly from the differential carrier.

HINT:

Tag the 2 rear differential case bearings (outer) so that they can be reinstalled in the correct locations.



Hide 11.REMOVE DIFFERENTIAL DRIVE PINION

a.
C325766

Using a press, remove the differential drive pinion with rear differential drive pinion bearing spacer from the differential carrier.

NOTICE:

Do not drop the differential drive pinion.



Hide 41231 12.REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

a.
C325767

Remove the rear differential drive pinion bearing spacer from the differential drive pinion.


Hide 41201A 13.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C325527N01
1.531,0.896 1.406,0.167 1.406,0.167 1.021,0.167 false 0.677,0.083 1.135,0.281 0.458,0.198 10 false SST

Using SST and a press, press out the rear drive pinion rear tapered roller bearing (inner) from the differential drive pinion.

SST
09555-55010  

NOTICE:

Do not drop the differential drive pinion.


HINT:

If the differential drive pinion or differential ring gear is damaged, replace them as a set.



Hide 41201B 14.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C325523

Remove the rear drive pinion front tapered roller bearing (inner) from the differential carrier.


Hide 41201B 15.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C325528C01
0.323,0.844 0.323,0.594 0.323,0.594 0.656,0.594 false 2.146,1.719 2.146,1.25 2.146,1.25 2.448,0.917 true 0.219,0.865 0.677,1.063 0.458,0.198 10 false SST 2.094,1.76 2.406,1.958 0.313,0.198 10 false *1
*1 Rear Drive Pinion Front Tapered Roller Bearing (Outer)


Using SST, remove the rear drive pinion front tapered roller bearing (outer) from the differential carrier.

SST
09308-00010  


Hide 41115 16.REMOVE DIFFERENTIAL OIL STORAGE RING

a.
C325529C01
1.052,3.167 1.958,3.167 1.958,3.167 2.271,2.833 true 0.771,1.01 0.927,1.688 0.927,1.688 1.24,1.688 true 0.729,3.073 1.188,3.271 0.458,0.198 10 false SST 1.302,1.604 1.615,1.802 0.313,0.198 10 false *1
*1 Differential Oil Storage Ring


Using SST and a hammer, tap out the differential oil storage ring from the differential carrier.

SST
09316-60011  (09316-00011)


Hide 41201A 17.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C325530

Using a brass bar and hammer, tap out the rear drive pinion rear tapered roller bearing (outer) and adjust shim from the differential carrier.

If the bearing is damaged during removal, replace it.


Hide 18.REMOVE DIFFERENTIAL RING GEAR

a.
C326626C01
2.458,1.104 2.969,1.104 false 2.417,1.021 2.792,1.021 2.792,1.021 2.792,1.104 true 3.031,1.01 3.344,1.208 0.313,0.198 10 false *a
*a Matchmark


Place matchmarks on the differential ring gear and differential case.


b.

Remove the 12 differential ring gear set bolts.


c.
C326627

Using a plastic-faced hammer, tap on the differential ring gear to remove it from the differential case.


Hide 19.INSPECT DIFFERENTIAL CASE ASSEMBLY RUNOUT

HINT:

If the ring gear runout is within the specified value (refer to the "Inspect Runout of Differential Ring Gear" procedure above), skip this step.


a.

Install the rear differential case bearings (outer) to the differential case.


b.

Install the differential case assembly to the differential carrier.


c.

Install the 2 plate washers.


d.

Install the 2 differential bearing caps to the differential carrier with the 4 bolts.

Torque:
140 N*m (1428 kgf*cm, 103 ft.*lbf)


e.
C326628C01
0.229,1.292 0.542,1.49 0.313,0.198 10 false *a
*a 92 mm (3.86 in.)


Using a dial indicator, measure the differential case runout.

Maximum runout:

0.07 mm (0.00276 in.)



f.

Remove the 4 bolts and 2 differential bearing caps.


g.

Remove the 2 plate washers.


h.

Remove the differential case assembly.


i.

Remove the rear differential case bearings (outer).


Hide 41301A 20.REMOVE REAR DIFFERENTIAL CASE BEARING

a.
C326629C01
0.771,0.698 0.771,0.229 0.771,0.229 0.542,0.229 false 2.208,0.271 2.521,0.469 0.313,0.198 10 false *a 0.094,0.875 0.406,1.073 0.313,0.198 10 false *b 0.219,0.167 0.677,0.365 0.458,0.198 10 false SST
*a Turn
*b Hold


Using SST, remove the 2 rear differential case bearings (inner) from the differential case.

SST
09950-40011  09950-60010  (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09958-04011)
09950-60010  (09951-00360)

HINT:

Do not remove the rear differential case bearings (inner) when not replacing the differential case assembly.



Hide 21.DISASSEMBLE DIFFERENTIAL CASE

a.
C236667

Using a chisel and hammer, unstake the differential case.


b.
C326616

Using a pin punch and hammer, tap out the straight pin.


c.
C236669

Remove the following parts from the differential case.

1.
C236670C04
0.563,0.542 0.563,0.219 0.563,0.219 0.396,0.219 false 0.906,0.635 0.906,0.167 0.906,0.167 0.979,0.167 false 1.635,1.052 1.635,0.5 1.635,0.5 1.49,0.5 false 2.063,0.479 2.063,0.125 2.063,0.125 1.958,0.125 false 2.75,0.51 3,0.51 false 2.375,1.604 2.375,1.854 false 2.75,1.688 2.75,1.833 false 0.552,1.458 0.552,1.177 0.552,1.177 0.427,1.177 false 1.146,1.708 1.146,1.896 1.146,1.896 1.292,1.896 false 1.365,1.813 1.573,1.979 0.208,0.167 10 false *1 0.198,0.146 0.406,0.313 0.208,0.167 10 false *5 1.281,0.427 1.49,0.594 0.208,0.167 10 false *3 1.76,0.052 1.969,0.219 0.208,0.167 10 false *1 3.052,0.427 3.26,0.594 0.208,0.167 10 false *2 2.313,1.906 2.521,2.073 0.208,0.167 10 false *4 2.708,1.885 2.917,2.052 0.208,0.167 10 false *5 1.052,0.104 1.26,0.271 0.208,0.167 10 false *4 0.229,1.115 0.438,1.281 0.208,0.167 10 false *2
*1 Side Gear
*2 Rear No. 1 Differential Side Gear Thrust Washer
*3 Pinion Shaft
*4 Pinion Gear
*5 Pinion Gear Thrust Washer


Side gear (2 pieces)

2.

Rear No. 1 differential side gear thrust washer (2 pieces)

3.

Pinion shaft

4.

Pinion gear (2 pieces)

5.

Pinion gear thrust washer (2 pieces)



Hide 22.INSPECT DIFFERENTIAL GEAR KIT

a.

Check that the differential pinion and differential side gear are not damaged.

If the differential pinion or differential side gear is damaged, replace the differential gear kit.


Hide 23.INSPECT DIFFERENTIAL CASE

a.

Check that the differential case is not damaged.

If the differential case is damaged, replace it.