Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › FRONT SPEED SENSOR(for 4WD and Pre-Runner) › from 2016.01
RM3270E _54 Brake _041691 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0243226 FRONT SPEED SENSOR(for 4WD and Pre-Runner) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  FRONT SPEED SENSOR(for 4WD and Pre-Runner)  INSTALLATION  


PROCEDURE

Hide 89543 1.INSTALL FRONT SPEED SENSOR LH

a.
C322645

Install the skid control sensor clamp to the steering knuckle with the bolt.

Torque:
13.5 N*m (138 kgf*cm, 10 ft.*lbf)


b.

Install the speed sensor to the steering knuckle with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

Make sure there are no pieces of iron or other foreign matter attached to the sensor tip.

·

While inserting the speed sensor into the steering knuckle hole, do not strike or damage the sensor tip.

·

After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the knuckle.

·

When installing the sensor, do not twist the wire harness.




c.
C322643

Install the harness clamp with the bolt.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)

NOTICE:
·

When installing the clamp, do not twist the wire harness.

·

Make sure the clamp rotation stopper touches the installation position.




d.

Attach the clamp.


e.
C322638

Attach the clamp.


f.

Install the 2 harness clamps with the 2 bolts.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)

NOTICE:
·

When installing the clamps, do not twist the wire harness.

·

Make sure the clamp rotation stopper touches the installation position.




g.
C322637

Attach the 2 clamps.

NOTICE:

When attaching the clamps, do not twist the wire harness.



h.
C322635

Attach the 2 clamps.

NOTICE:

When attaching the clamps, do not twist the wire harness.



i.

Connect the connector and attach the clamp.

NOTICE:
·

Do not attach the connector to the radiator fan shroud before connecting the connector.

·

Securely connect the connector.




Hide 89542 2.INSTALL FRONT SPEED SENSOR RH

a.
C322644

Install the skid control sensor clamp to the steering knuckle with the bolt.

Torque:
13.5 N*m (138 kgf*cm, 10 ft.*lbf)


b.

Install the speed sensor to the steering knuckle with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

Make sure there are no pieces of iron or other foreign matter attached to the sensor tip.

·

While inserting the speed sensor into the knuckle hole, do not strike or damage the sensor tip.

·

After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the knuckle.

·

When installing the sensor, do not twist the wire harness.




c.

Attach the clamp.


d.
C322642

Install the harness clamp with the bolt.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)

NOTICE:
·

When installing the clamp, do not twist the wire harness.

·

Make sure the clamp rotation stopper touches the installation position.




e.

Attach the clamp.


f.
C322640

Install the 2 harness clamps with the 2 bolts.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)

NOTICE:
·

When installing the clamps, do not twist the wire harness.

·

Make sure the clamp rotation stopper touches the installation position.




g.

Attach the clamp.


h.
C322639

Attach the 2 clamps.

NOTICE:

When attaching the clamps, do not twist the wire harness.



i.
C322636

Attach the 2 clamps.

NOTICE:

When attaching the clamps, do not twist the wire harness.



j.

Connect the connector and attach the clamp.

NOTICE:
·

Do not attach the connector to the radiator fan shroud before connecting the connector.

·

Securely connect the connector.




k.
C322641

for 1GD-FTV, 2GD-FTV:

i.

Install the upper arm heat insulator to the front suspension tower with the 2 bolts.

Torque:
25.5 N*m (260 kgf*cm, 19 ft.*lbf)



Hide 3.INSTALL FRONT WHEEL