Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function) › from 2016.01
RM3270E _58 Vehicle Interior _041706 THEFT DETERRENT / KEYLESS ENTRY _0212879 SMART ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  B27B0  Lost Communication with MainBody Module  


DESCRIPTION

The certification ECU (smart key ECU assembly) and body ECU communicate using unidirectional communication lines.

This DTC is output when the certification ECU (smart key ECU assembly) sends a request to the body ECU but does not receive a reply.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B27B0 Lost Communication with MainBody Module Certification ECU (smart key ECU assembly) sends request but body ECU does not reply within 10 seconds (1 trip detection logic*).
·

Certification ECU (smart key ECU assembly)

·

Body ECU

·

Harness or connector


DTC Output Confirmation Operation

Driver door open/close



*: Only output while a malfunction is present.

Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
·

Entry lock/unlock operation cannot be performed

·

Wireless lock/unlock operation cannot be performed


-

Related Data List and Active Test
DTC No. Data List and Active Test
B27B0 -

WIRING DIAGRAM

B348670E04
1.729,1.052 2.063,1.25 0.333,0.198 10 false PRG 1.74,1.677 2.073,1.875 0.333,0.198 10 false RDA 2.146,0.938 2.479,1.135 0.333,0.198 10 false 9 2.115,1.563 2.448,1.76 0.333,0.198 10 false 16 4.885,0.927 5.115,1.104 0.229,0.177 10 false 36 4.885,1.563 5.115,1.74 0.229,0.177 10 false 13 5.156,1.052 5.677,1.25 0.521,0.198 10 false PRG3 5.146,1.677 5.615,1.885 0.469,0.208 10 false RDA3 1.167,2.531 1.5,2.729 0.333,0.198 10 false G33 1.167,2.708 2.26,2.948 1.094,0.24 10 false Body ECU 4.854,2.531 5.188,2.729 0.333,0.198 10 false G17 4.854,2.719 6.396,3.177 1.542,0.458 10 false Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting.

Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

·

w/ Automatic Light Control System:

If the body ECU has been replaced, it is necessary to initialize the body ECU.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

w/ Door Control Battery:

As the door control battery is installed between the vehicle battery and body ECU, first perform the inspections to confirm that there are no malfunctions in the power source circuit for the body ECU before performing this troubleshooting procedure.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BODY ECU)
a.

Disconnect the G17 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G33 body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G17-36 (PRG3) - G33-9 (PRG) Always Below 1 Ω
G17-13 (RDA3) - G33-16 (RDA) Always Below 1 Ω
G17-36 (PRG3) or G33-9 (PRG) - Body ground Always 10 kΩ or higher
G17-13 (RDA3) or G33-16 (RDA) - Body ground Always 10 kΩ or higher



d.

Connect the G17 certification ECU (smart key ECU assembly) connector.


e.

Connect the G33 instrument panel junction block assembly (body ECU) connector.


Result:
Proceed to
OK
NG



OK

2.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC
a.

Open and close the driver door.


b.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
OK:

DTC B27B0 is not output.



Result:
Proceed to
OK
NG



OK

END (CONNECTOR WAS NOT CONNECTED PROPERLY)

NG

4.REPLACE BODY ECU
4.REPLACE BODY ECU
a.

Replace the body ECU with a new or known good one.



Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Combination Meter > Clear DTCs
50002 122

Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Open and close the driver door.


b.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
OK:

DTC B27B0 is not output.



Result:
Proceed to
OK
NG



OK

END (BODY ECU WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)