Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › from 2016.01
RM3270E _58 Vehicle Interior _041706 THEFT DETERRENT / KEYLESS ENTRY _0212881 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Horn Circuit  


DESCRIPTION

When the theft deterrent system is switched from the armed state to the alarm sounding state, the body ECU transmits a signal to cause the horn to sound at intervals of 0.4 seconds.

WIRING DIAGRAM

E318153E02
5.802,0.865 6.417,1.063 0.615,0.198 10 false HORN 5.615,0.865 6.229,1.063 0.615,0.198 10 false 9 4.604,0.979 5.219,1.177 0.615,0.198 10 false 2D 4.594,0.75 5.208,0.948 0.615,0.198 10 false 14 4.594,1.49 5.208,1.688 0.615,0.198 10 false 2Q 4.604,1.271 5.219,1.469 0.615,0.198 10 false 10 4.5,1.948 5.573,2.542 1.073,0.594 10 false Instrument Panel Junction Block Assembly 5.854,3.042 6.521,3.302 0.667,0.26 10 false A 5.854,3.198 7.073,3.406 1.219,0.208 10 false Body ECU 4.625,3.844 6.656,4.073 2.031,0.229 10 false to Horn Button Assembly 2.323,0.865 2.938,1.063 0.615,0.198 10 false 2 2.323,1.177 2.938,1.375 0.615,0.198 10 false 5 1.406,0.865 2.021,1.063 0.615,0.198 10 false 1 1.406,1.188 2.021,1.385 0.615,0.198 10 false 3 0.646,1.125 1.26,1.323 0.615,0.198 10 false HORN 1.156,1.604 2.531,2.073 1.375,0.469 10 false Horn Relay Assembly (HORN) 0.938,0.177 2.188,0.406 1.25,0.229 10 false from Battery 2.448,3.094 3.063,3.292 0.615,0.198 10 false 1 0.74,3.094 1.354,3.292 0.615,0.198 10 false 1 1.031,3.177 1.646,3.375 0.615,0.198 10 false A11 1.021,3.333 2.167,3.75 1.146,0.417 10 false High Pitched Horn Assembly 2.74,3.177 3.354,3.375 0.615,0.198 10 false A10 2.75,3.333 3.896,3.75 1.146,0.417 10 false Low Pitched Horn Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

w/ Automatic Light Control System:

If the body ECU has been replaced, it is necessary to initialize the body ECU.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

w/ Door Control Battery:

As the door control battery is installed between the vehicle battery and body ECU, first perform the inspections to confirm that there are no malfunctions in the power source circuit for the body ECU before performing this troubleshooting procedure.



PROCEDURE

1.INSPECT HORN
a.

Press the horn switch and check if the horn sounds.


Result:
Result Proceed to
Horn sounds A
Horn does not sound B



A

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

B

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

b.

Disconnect the instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

B343149C14
2.198,0.438 2.5,0.615 0.302,0.177 5.542,0.26 5.844,0.438 0.302,0.177 2.375,1.25 2.625,0.938 true 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a 2.302,0.448 2.615,0.646 0.313,0.198 10 false A 5.594,0.271 5.906,0.469 0.313,0.198 10 false 2D 2.167,1.281 2.781,1.479 0.615,0.198 10 false HORN
*a Component without harness connected (Instrument Panel Junction Block Assembly) - -


Standard Resistance:
Tester Connection Condition Specified Condition
2D-14 - A-9 (HORN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY