Home › Engine / Hybrid System › 2KD-FTV ENGINE MECHANICAL › ENGINE UNIT › from 2016.01
RM3270E _51 Engine / Hybrid System _048931 2KD-FTV ENGINE MECHANICAL _0243273 ENGINE UNIT A

2KD-FTV ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
·

Injector assembly (including shuffling the injector assemblies between the cylinders)

·

Common rail assembly

·

Cylinder head sub-assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

No. 3 injection pipe sub-assembly

·

No. 4 injection pipe sub-assembly


·

Supply pump assembly

·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing Gear Case Assembly


Fuel inlet pipe sub-assembly

·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and fuel inlet pipe sub-assembly, clean them with a brush and compressed air.



PROCEDURE

Hide 11301Q 1.INSTALL INJECTION PUMP OIL SEAL

a.
A352066N01
1.865,1.646 2.406,1.927 2.406,1.927 2.521,1.927 true 0.625,1.51 1.563,1.51 true 0.708,0.802 0.875,0.802 0.875,0.802 1.708,1.115 true 2.552,1.833 2.885,2.01 0.333,0.177 10 false SST 0.344,1.417 0.677,1.594 0.333,0.177 10 false SST 0.417,0.698 0.75,0.875 0.333,0.177 10 false SST

Using SST and a hammer, tap in a new injection pump oil seal until its surface is flush with the timing gear cover edge.

SST
09223-15020  
09502-12010  
09950-70010  (09951-07100)

NOTICE:
·

Keep the lip free from foreign matter.

·

Do not tap the supply pump oil seal at an angle.




b.

Apply MP grease to the lip of the injection pump oil seal.


Hide 11303A 2.INSTALL FRONT CRANKSHAFT OIL SEAL

a.
A352067N01
1.719,1.073 0.844,0.802 0.844,0.802 0.667,0.802 true 0.365,0.708 0.688,0.875 0.323,0.167 10 false SST

Using SST and a hammer, tap in a new front crankshaft oil seal until its surface is flush with the timing gear cover edge.

SST
09214-76011  

NOTICE:
·

Keep the lip free from foreign matter.

·

Do not tap the front crankshaft oil seal at an angle.




b.

Apply MP grease to the lip of the front crankshaft oil seal.


Hide 11381A 3.INSTALL REAR ENGINE OIL SEAL

a.
A352065N01
0.583,0.833 0.802,0.833 0.802,0.833 1.5,1.167 true 1.833,1.5 2.333,1.333 2.333,1.333 2.5,1.333 false 0.292,0.74 0.625,0.906 0.333,0.167 10 false SST 2.531,1.229 2.865,1.396 0.333,0.167 10 false SST

Using SST and a hammer, tap in a new rear engine oil seal until its surface is flush with the rear engine oil seal retainer edge.

SST
09518-36030  
09950-70010  (09951-07100)

NOTICE:
·

Keep the lip free from foreign matter.

·

Do not tap the rear engine oil seal at an angle.




b.

Apply MP grease to the lip of the rear engine oil seal.


Hide 11381 4.INSTALL REAR ENGINE OIL SEAL RETAINER

a.

Remove any old seal packing (FIPG material) from the cylinder block sub-assembly.


b.
A246541C06
2.313,0.625 2.667,0.302 2.667,0.302 2.75,0.302 false 2.76,0.208 2.979,0.375 0.219,0.167 10 false *a
*a Seal Packing


Apply seal packing to the places shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

4 mm (0.157 in.)


NOTICE:

After applying seal packing, install the rear engine oil seal retainer within 3 minutes and tighten the bolts within 15 minutes.



c.

Install the rear engine oil seal retainer with the 5 bolts. Alternately tighten the 5 bolts in several passes.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 11320 5.INSTALL TIMING GEAR CASE ASSEMBLY

a.
A060152C04
1.646,0.688 0.552,0.688 true 1.813,1.708 0.771,1.708 true 0.375,0.594 0.531,0.74 0.156,0.146 10 false *1 0.594,1.615 0.75,1.76 0.156,0.146 10 false *1
*1 New O-Ring


Install 2 new O-rings to the cylinder block sub-assembly.


b.
A239302C02
2.323,0.781 2.74,0.26 2.74,0.26 2.833,0.26 true 2.854,0.177 3.01,0.333 0.156,0.156 10 false *1
*1 New Gasket


Install a new gasket to the groove of the timing gear case assembly.


c.

Remove any old seal packing (FIPG material).


d.
A100875C06
0.51,1.646 1.208,1.646 true 0.302,1.552 0.563,1.75 0.26,0.198 10 false *a
*a Seal Packing


Apply seal packing to the timing gear case assembly as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

4 mm (0.157 in.)


NOTICE:

After applying seal packing, install the timing gear case assembly within 3 minutes and tighten the bolts within 15 minutes.



e.
A303437N03
1.615,1.406 1.771,1.604 0.156,0.198 10 false A

Install the timing gear case assembly to the cylinder block sub-assembly with the union bolt and 8 bolts.

Torque:
for union bolt (A) : 16 N*m (163 kgf*cm, 12 ft.*lbf)
for bolt : 13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 15104 6.INSTALL OIL STRAINER SUB-ASSEMBLY

a.

Install a new gasket and the oil strainer sub-assembly with the 2 bolts and 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 12101 7.INSTALL OIL PAN SUB-ASSEMBLY

A352068N01
1.396,1.938 1.552,2.135 0.156,0.198 10 false A 2.458,1.938 2.615,2.135 0.156,0.198 10 false B 1.385,1.479 1.552,1.646 0.167,0.167 10 true A 2.448,1.479 2.615,1.646 0.167,0.167 10 true B 0.875,2.333 1.292,2.5 0.417,0.167 10 false A - A 2.5,2.333 2.917,2.5 0.417,0.167 10 false B - B

a.

Remove any old seal packing (FIPG material).


b.

Apply seal packing to the oil pan sub-assembly as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

4 mm (0.157 in.)


NOTICE:

After applying seal packing, install the oil pan sub-assembly within 3 minutes and tighten the bolts and nuts within 15 minutes.



c.

Install the oil pan sub-assembly to the cylinder block sub-assembly with the 22 bolts and 2 nuts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 13613E 8.INSTALL INJECTION GEAR

a.

Install a new O-ring and the fuel supply pump assembly with the 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Temporarily install the injection gear with the nut.

HINT:

Fit the key (protrusion) of the fuel supply pump assembly into the key slot of the injection gear.



c.
A069844C01
1.26,1.656 1.021,1.958 1.021,1.958 0.885,1.958 true 0.677,1.865 0.875,2.063 0.198,0.198 10 true *1
*1 New O-Ring


Install a new O-ring to the injection gear.


d.
A069845N02
2.917,1 2.854,1.313 true 2.677,1.344 3.031,1.521 0.354,0.177 10 false SST

Install the injection gear set nut.


e.

Using SST, tighten the set nut.

SST
09960-10010  (09962-01000, 09963-01000)

Torque:
63.7 N*m (650 kgf*cm, 47 ft.*lbf)


Hide 13521 9.INSTALL CRANKSHAFT TIMING GEAR

a.
A061827N02
2.25,1.063 2.979,1.708 true 2.833,1.74 3.156,1.927 0.323,0.188 10 false SST

Position the crankshaft timing gear with the "1" timing marks facing forward.


b.

Align the key groove of the crankshaft timing gear with the set key on the crankshaft.


c.

Using SST and a hammer, tap on the crankshaft timing gear to install it.

SST
09223-00010  


Hide 13581 10.INSTALL NO. 1 IDLE GEAR SHAFT

a.
A069846C06
2.302,1.219 2.052,1.708 2.052,1.708 1.958,1.708 true 1.729,1.625 1.927,1.802 0.198,0.177 10 false *a
*a Engine Oil


Apply a coat of engine oil to the No. 1 idle gear shaft.


b.
A060159C07
1.573,1.063 1.208,0.521 1.208,0.521 1.073,0.521 true 0.854,0.417 1.031,0.583 0.177,0.167 10 true *a
*a Oil Hole


Install the No. 1 idle gear shaft as shown in the illustration.


Hide 13538 11.INSTALL NO. 2 IDLE SUB GEAR

a.
A060166

Using a cloth or equivalent, mount the No. 1 idle gear in a vise as shown in the illustration.

NOTICE:

Be careful not to damage the gear.



b.
A303438C02
2.229,1.427 2.49,1.188 2.49,1.188 2.688,1.188 false 0.76,1.458 0.917,1.458 0.917,1.458 1.417,1.74 true 0.813,2.688 0.948,2.688 0.948,2.688 1.51,3.604 true 2.208,2.542 2.552,2.542 false 2.135,0.74 2.396,0.5 2.396,0.5 2.594,0.5 false 2.677,0.406 2.99,0.604 0.313,0.198 10 false *1 2.729,1.052 3.042,1.25 0.313,0.198 10 false *2 2.635,2.448 2.948,2.646 0.313,0.198 10 false *3 0.552,1.344 0.865,1.542 0.313,0.198 10 false *4 0.635,2.594 0.948,2.792 0.313,0.198 10 false *4
*1 Wave Washer
*2 No. 2 Idle Sub Gear
*3 Gear Spring
*4 Pin


Install the gear spring.


c.

Install the No. 2 idle sub gear.

HINT:

Align the pins on the gears with the spring ends.



d.

Install the wave washer.


e.

Using snap ring pliers, install the snap ring.


f.
A060164C06
2.292,0.469 2.51,0.198 2.51,0.198 2.573,0.198 false 0.958,1.906 0.594,1.698 0.594,1.698 0.49,1.698 false 2.094,1.76 1.563,1.958 1.563,1.958 1.479,1.958 true 2.021,1.604 2.677,1.438 2.677,1.438 2.781,1.438 true 2.604,0.104 2.938,0.25 0.333,0.146 10 false SST 1.281,1.865 1.458,2.021 0.177,0.156 10 false *2 2.813,1.365 2.969,1.521 0.156,0.156 10 false *3 0.302,1.594 0.469,1.75 0.167,0.156 10 false *1
*1 Service Bolt
*2 No. 1 Idle Gear
*3 No. 2 Idle Sub Gear
V100135

Turn


Using SST, align the holes of the No. 1 idle gear and No. 2 idle sub gear by turning the No. 2 idle sub gear clockwise and temporarily install a service bolt.

SST
09960-10010  (09962-01000, 09963-00700)


g.

Align the gear teeth of the No. 1 idle gear and No. 2 idle sub gear and tighten the service bolt.


Hide 13525 12.INSTALL NO. 1 IDLE GEAR

a.
G036757C02
1.948,0.583 2.583,0.281 2.583,0.281 2.698,0.281 true 2.063,0.073 2.271,0.24 0.208,0.167 10 true *a 2.76,0.198 3.125,0.365 0.365,0.167 10 false SST
*a Turn


Align the "4" and "5" timing marks of the No. 1 idle gear and crankshaft timing gear.


b.

Using SST, turn the injection gear and align the "4" timing marks of the No. 1 idle gear and injection gear, and then mesh the gears.

SST
09960-10010  (09962-01000, 09963-00700)


c.
A222334C02
2.438,1.667 1.406,1.844 1.406,1.844 1.156,1.844 true 0.958,1.75 1.135,1.917 0.177,0.167 10 false *1
*1 Service Bolt


Position the idle gear thrust plate with the protrusion facing forward.


d.

Align the bolt holes and install the idle gear thrust plate with the 2 bolts.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


e.

Remove the service bolt.


Hide 19315 13.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

a.

Align the key groove of the No. 1 crankshaft position sensor plate with the set key.


b.

Install the No. 1 crankshaft position sensor plate to the crankshaft with the cupped side facing outward.


Hide 14.INSTALL TIMING GEAR COVER

a.

Remove any old seal packing (FIPG material).


b.
A352069C01
1.646,0.708 2,0.438 2,0.438 2.177,0.438 false 2.208,0.333 2.438,0.5 0.229,0.167 10 false *a
*a Seal Packing


Apply seal packing to the timing gear cover as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

4 mm (0.157 in.)


NOTICE:

After applying seal packing, install the timing gear cover within 3 minutes and tighten the bolts within 15 minutes.



c.

Install a new O-ring to the timing gear case assembly.


d.

Install the timing gear cover to the timing gear case assembly with the 14 bolts and 2 nuts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


e.
A248630

Remove the screw plug and gasket.


f.

Pour approximately 50 cc (3.05 cu. in.) of engine oil into the oil pump.


g.

Install a new gasket and the screw plug.

Torque:
41.5 N*m (423 kgf*cm, 31 ft.*lbf)


h.

Install the No. 1 vacuum transmitting pipe with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 16100 15.INSTALL ENGINE WATER PUMP ASSEMBLY

a.

Install a new gasket and the engine water pump assembly to the cylinder block sub-assembly with the 5 bolts and 2 nuts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 11101 17.INSTALL CYLINDER HEAD SUB-ASSEMBLY

Hide 13751 18.INSTALL VALVE LIFTER

a.

Install the valve lifters to the cylinder head sub-assembly.


b.

Check that each valve lifter rotates smoothly by hand.


Hide 12581C 20.INSTALL CYLINDER BLOCK INSULATOR

Hide 23.INSPECT AND ADJUST VALVE CLEARANCE

Hide 23670 24.INSTALL INJECTOR ASSEMBLY

Hide 11201 26.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 12108 27.INSTALL OIL FILLER CAP SUB-ASSEMBLY