Home › Engine / Hybrid System › 2KD-FTV ENGINE MECHANICAL › CYLINDER HEAD › from 2016.01
RM3270E _51 Engine / Hybrid System _048931 2KD-FTV ENGINE MECHANICAL _0243274 CYLINDER HEAD A

2KD-FTV ENGINE MECHANICAL  CYLINDER HEAD  REPLACEMENT  


PROCEDURE

Hide 11122 1.REPLACE INTAKE VALVE GUIDE BUSH

a.

Gradually heat the cylinder head sub-assembly to approximately 80 to 100°C (176 to 212°F).


b.
A059922N04
1.552,1.5 0.969,0.583 0.969,0.583 1.521,0.854 true 0.667,0.49 0.979,0.656 0.313,0.167 10 false SST

Using SST and a hammer, tap out the intake valve guide bush.

SST
09201-10000  (09201-01060)
09950-70010  (09951-07100)


c.

Using a caliper gauge, measure the intake valve guide bush bore diameter of the cylinder head sub-assembly.


d.

Select a new intake valve guide bush.

New Guide Bush:
Item Specified Condition
Bush bore diameter 10.985 to 11.006 mm (0.432 to 0.433 in.) 11.035 to 11.056 mm (0.434 to 0.435 in.)
Bush to be used STD O/S 0.05


If the valve guide bush bore diameter of the cylinder head sub-assembly is more than 11.006 mm (0.433 in.), machine the valve guide bush bore diameter to between 11.035 and 11.056 mm (0.434 and 0.435 in.).

If the valve guide bush bore diameter of the cylinder head sub-assembly is more than 11.056 mm (0.435 in.), replace the cylinder head sub-assembly.


e.

Gradually heat the cylinder head sub-assembly to approximately 80 to 100°C (176 to 212°F).


f.
A303227N02
0.865,1.479 1.792,1.385 1.792,1.385 0.906,1.031 true 1.844,1.323 2.302,1.521 0.458,0.198 10 false SST 3.188,0.417 3.375,0.656 0.188,0.24 10 false H

Using SST and a hammer, tap in a new intake valve guide bush to the specified protrusion height.

SST
09201-10000  (09201-01060)
09950-70010  (09951-07100)

Standard protrusion height (H):

10.3 to 10.7 mm (0.406 to 0.421 in.)



g.
A059166C06
1.635,0.635 1.313,0.313 1.313,0.313 1.229,0.313 false 1.031,0.219 1.208,0.396 0.177,0.177 10 false *a
*a Sharp 6.0 mm Reamer


Using a sharp 6.0 mm reamer, ream the intake valve guide bush to obtain the standard clearance between the intake valve guide bush and valve stem.

Standard clearance:

0.025 to 0.060 mm (0.00984 to 0.00236 in.)



Hide 11126 2.REPLACE EXHAUST VALVE GUIDE BUSH

a.

Gradually heat the cylinder head sub-assembly to approximately 80 to 100°C (176 to 212°F).


b.
A059923N04
1.604,0.865 1.104,0.625 1.104,0.625 1.625,1.604 true 0.802,0.521 1.146,0.698 0.344,0.177 10 false SST

Using SST and a hammer, tap out the exhaust valve guide bush.

SST
09201-10000  (09201-01060)
09950-70010  (09951-07100)


c.

Using a caliper gauge, measure the exhaust valve guide bush bore diameter of the cylinder head sub-assembly.


d.

Select a new exhaust valve guide bush.

New Guide Bush:
Item Specified Condition
Bush bore diameter 10.985 to 11.006 mm (0.4325 to 0.4333 in.) 11.035 to 11.056 mm (0.4344 to 0.4353 in.)
Bush to be used STD O/S 0.05


If the valve guide bush bore diameter of the cylinder head sub-assembly is more than 11.006 mm (0.4333 in.), machine the valve guide bush bore diameter to between 11.035 and 11.056 mm (0.4344 and 0.4353 in.).

If the valve guide bush bore diameter of the cylinder head sub-assembly is more than 11.056 mm (0.4353 in.), replace the cylinder head sub-assembly.


e.

Gradually heat the cylinder head sub-assembly to approximately 80 to 100°C (176 to 212°F).


f.
A303228N02
0.969,1.573 1.688,1.583 1.688,1.583 1,0.958 true 1.76,1.49 2.219,1.688 0.458,0.198 10 false SST 3.135,0.813 3.323,1.042 0.188,0.229 10 false H

Using SST and a hammer, tap in a new exhaust valve guide bush to the specified protrusion height.

SST
09201-10000  (09201-01060)
09950-70010  (09951-07100)

Standard protrusion height (H):

10.3 to 10.7 mm (0.406 to 0.421 in.)



g.
A059170C06
1.635,0.656 1.292,0.313 1.292,0.313 1.198,0.313 false 1,0.208 1.219,0.385 0.219,0.177 10 false *a
*a Sharp 6.0 mm Reamer


Using a sharp 6.0 mm reamer, ream the exhaust valve guide bush to obtain the standard clearance between the exhaust valve guide bush and valve stem.

Standard clearance:

0.035 to 0.070 mm (0.00138 to 0.00276 in.)



Hide 3.REPLACE RING PIN

HINT:

It is not necessary to remove a ring pin unless it is being replaced.


a.

Remove the ring pin from the cylinder head sub-assembly.


b.

Using a plastic-faced hammer, tap in a new ring pin to the cylinder head sub-assembly until the pin stops.

Standard protrusion:

Less than 5 mm (0.197 in.)


A200441C07
3.573,0.823 3.781,1 0.208,0.177 10 false *a 5.813,1.281 6.031,1.469 0.219,0.188 10 false *c 4.219,1.354 4.427,1.531 0.208,0.177 10 false *b
*a 8 mm (0.315 in.) *b 10 mm (0.394 in.)
*c Less than 5 mm (0.197 in.) - -