Home › Engine / Hybrid System › 2GD-FTV FUEL › FUEL SUPPLY PUMP › from 2016.01
RM3270E _51 Engine / Hybrid System _048924 2GD-FTV FUEL _0243284 FUEL SUPPLY PUMP A

2GD-FTV FUEL  FUEL SUPPLY PUMP  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
·

Injector assembly (including shuffling the injector assemblies between the cylinders)

·

Common rail assembly

·

Cylinder head sub-assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


·

Supply pump assembly

·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.

·

Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.

·

Make sure foreign matter does not enter the fuel path.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 51441 4.REMOVE NO. 1 ENGINE UNDER COVER

Hide 17362B 6.REMOVE NO. 2 AIR TUBE

Hide 16571C 7.REMOVE NO. 1 RADIATOR HOSE

Hide 44360 8.DISCONNECT VANE PUMP OIL RESERVOIR ASSEMBLY

Hide 44369A 9.REMOVE NO. 1 OIL RESERVOIR BRACKET

Hide 16470 10.REMOVE RADIATOR RESERVOIR ASSEMBLY

Hide 16711 11.REMOVE FAN SHROUD

Hide 16620 12.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 23273H 13.REMOVE NO. 2 FUEL HOSE

a.
A344931

Slide the 2 clips and remove the No. 2 fuel hose from the supply pump assembly and No. 3 nozzle leakage pipe assembly.


Hide 23271H 14.REMOVE NO. 1 FUEL HOSE

a.
A344932

Slide the 2 clips and remove the No. 1 fuel hose from the supply pump assembly and No. 2 fuel pipe.


Hide 22803 15.REMOVE FUEL INJECTION PUMP COVER SUB-ASSEMBLY

A344933

a.

Remove the fuel injection pump cover sub-assembly from the supply pump assembly.


Hide 16.REMOVE FUEL PUMP MOTOR WIRE

a.
A344934

Disconnect the fuel pump motor wire connector.


b.

Detach the clamp and remove the fuel pump motor wire.


Hide 11324 17.REMOVE TIMING CHAIN COVER PLATE

a.
A344936

Remove the 3 bolts and timing chain cover plate.


b.

Remove the gasket.


Hide 22100 18.REMOVE SUPPLY PUMP ASSEMBLY

NOTICE:
·
A347307

Do not hold the supply pump assembly by the parts indicated by the arrows in the illustration.

·

With SST set, do not turn the crankshaft more than a half rotation.



a.
A349352C01
1.625,2.031 1.625,1.365 true 1.49,2.042 1.49,1.344 true 1.167,2.042 1.625,2.042 true 0.958,1.927 1.271,2.083 0.313,0.156 10 false *a
*a Timing Mark


Align the timing mark of the crankshaft pulley sub-assembly and timing chain cover by rotating the crankshaft clockwise.


b.
A344937C01
0.5,1.51 0.75,1.51 0.75,1.51 0.844,1.698 true 1.271,2.01 1.708,2.01 false 0.708,1.99 1.021,2.146 0.313,0.156 10 false *a 0.177,1.427 0.635,1.625 0.458,0.198 10 true SST 1.75,1.938 2.208,2.135 0.458,0.198 10 true SST
*a Hold
V100135

Turn


Using SST, hold the crankshaft pulley assembly and loosen the fuel supply pump shaft nut.

SST
09213-58014  (91551-80840)
09330-00021  

NOTICE:

Do not excessively loosen the supply pump shaft nut, otherwise SST cannot be installed.


HINT:

Rotate the supply pump shaft nut once to loosen it.



c.
A347057

Loosen the 3 nuts from the supply pump assembly.

NOTICE:

Do not completely remove the nuts. Otherwise, the supply pump assembly may fall off.



d.
A344938E01
1.219,1.552 1.417,1.552 1.417,1.552 1.771,1.313 true 0.865,1.458 1.323,1.656 0.458,0.198 10 true SST

Install SST with 3 bolts.

SST
09241-11010  

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Install SST with the bolts included with SST.


HINT:
A347063C01
1.99,3.802 2.271,4.365 2.271,4.365 2.49,4.365 true 0.375,0.167 0.688,0.323 0.313,0.156 10 false *a 0.427,2.563 0.74,2.719 0.313,0.156 10 false *b 2.521,4.26 2.833,4.417 0.313,0.156 10 false *c
*a Engine Front Side
*b Engine Rear Side
*c SST Hexagonal Portion


·

Make sure that the installation direction of SST is as shown in the illustration.

·

Align the hexagonal portion of SST with the supply pump shaft nut to install SST.




e.
A344939C01
0.573,1.333 0.802,1.333 0.802,1.333 1.031,1.563 true 1.708,1.854 2.167,1.854 false 2.438,0.813 2.615,1.125 2.615,1.125 2.802,1.125 true 0.969,1.948 1.281,2.104 0.313,0.156 10 false *a 2.813,1.031 3.271,1.229 0.458,0.198 10 true SST 2.198,1.781 2.656,1.979 0.458,0.198 10 true SST 0.25,1.271 0.708,1.469 0.458,0.198 10 true SST
*a Hold
V100135

Turn


Install the handle to SST. While holding the crankshaft pulley assembly in place with the crankshaft holding tool, turn the handle in the counterclockwise direction to disconnect the supply pump assembly.

SST
09213-58014  (91551-80840)
09330-00021  
09241-11010  


f.

Remove the 3 nuts and supply pump assembly from the timing chain case assembly.


g.
A347064

Remove the O-ring from the supply pump assembly.