Home › Engine / Hybrid System › 2TR-FE FUEL › FUEL SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _048940 2TR-FE FUEL _0243339 FUEL SYSTEM G

2TR-FE FUEL  FUEL SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK FUEL PUMP OPERATION AND INSPECT FOR FUEL LEAKS

a.

Connect the GTS to the DLC3.

i.

Turn the engine switch on (IG).

NOTICE:

Do not start the engine.



ii.

Turn the GTS on.


iii.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5


b.

Check fuel pump operation.

i.

Check for pressure in the fuel inlet tube from the fuel line. Check that the sound of fuel flowing in the fuel tank can be heard.

If there is no sound, check the instrument panel junction block, fuel pump, ECM and wiring connector.



c.

Inspect for fuel leaks.

i.

Check that there are no fuel leaks after performing maintenance anywhere on the system.

If there are fuel leaks, repair or replace parts as necessary.



Hide 2.CHECK FUEL PRESSURE


b.

Discharge the fuel system pressure.

Click hereEngine / Hybrid System>2TR-FE FUEL>FUEL SYSTEM>PRECAUTION


c.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION




d.
A346776

Disconnect the No. 1 fuel hose.

Click hereEngine / Hybrid System>2TR-FE FUEL>FUEL SYSTEM>PRECAUTION


e.
A309363C01
1,0.792 1.188,0.792 1.188,0.792 1.5,0.583 false 2.115,2.167 2.313,2.167 2.313,2.167 2.51,2.5 false 0.615,1.771 0.813,1.771 0.813,1.771 0.958,2.083 false 1.01,2.927 1.188,2.927 1.188,2.927 1.531,2.698 false 2.344,4.229 2.542,4 2.542,4 2.719,4 false 1.052,4.156 1.271,4.156 1.271,4.156 1.583,3.927 false 1.531,1.042 2.021,1.042 false 2.375,1.042 2.656,0.875 2.656,0.875 2.823,0.875 false 2.5,1.698 2.833,1.698 false 0.688,3.885 0.865,3.885 0.865,3.885 1.073,3.74 false 1.823,3.469 2.156,3.469 false 0.854,4.052 1.052,4.25 0.198,0.198 10 false *d 1.323,0.927 1.521,1.125 0.198,0.198 10 false *b 0.813,2.823 1.01,3.021 0.198,0.198 10 false *c 2.323,1.594 2.521,1.792 0.198,0.198 10 false *f 1.917,2.052 2.115,2.25 0.198,0.198 10 false *e 0.792,0.677 0.99,0.875 0.198,0.198 10 false *a 0.417,1.667 0.615,1.865 0.198,0.198 10 false *1 0.479,3.781 0.677,3.979 0.198,0.198 10 false *b 2.188,3.365 2.385,3.563 0.198,0.198 10 false *b 2.76,3.896 2.958,4.094 0.198,0.198 10 false *2 2.854,0.76 3.052,0.958 0.198,0.198 10 false *c
*1 Fuel Pressure Pulsation Damper Assembly
*2 No. 1 Fuel Hose
*a SST (Fuel Tube Connector)
*b SST (Hose Band)
*c SST (Hose)
*d SST (T-Joint)
*e SST (Hose Joint)
*f SST (Gauge)


Install SST (pressure gauge) as shown in the illustration.

SST
09268-45101  (09268-41250, 09268-41260, 09268-41280, 09268-41500, 09268-41700, 95336-08070)


f.

Wipe off any gasoline.


g.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



h.

Operate the fuel pump.

i.

Connect the GTS to the DLC3.


ii.

Turn the engine switch on (IG).

NOTICE:

Do not start the engine.



iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5


i.

Measure the fuel pressure.

Standard fuel pressure:

281 to 287 kPa (2.87 to 2.93 kgf/cm2, 41 to 42 psi)


If the pressure is higher than the specification, replace the fuel pressure regulator.

If the pressure is below the specification, check the fuel hoses and connectors, fuel pump, fuel filter and fuel pressure regulator.


j.

Start the engine.


k.

Measure the fuel pressure.

Standard fuel pressure:

281 to 287 kPa (2.87 to 2.93 kgf/cm2, 41 to 42 psi)


If the pressure is not as specified, check the fuel pump, pressure regulator and/or injectors.


l.

Stop the engine.


m.

Check that the fuel pressure remains as specified for 5 minutes after the engine has stopped.

Standard fuel pressure:

147 kPa (1.5 kgf/cm2, 21 psi) or higher


If the pressure is not as specified, check the fuel pump, pressure regulator and/or injectors.


n.

Disconnect the cable from the negative (-) battery terminal and carefully remove SST and the fuel tube connector to prevent gasoline from spraying.


o.

Connect the No. 1 fuel hose.

Click hereEngine / Hybrid System>2TR-FE FUEL>FUEL SYSTEM>PRECAUTION