Home › Engine / Hybrid System › 2TR-FE FUEL › FUEL TANK › from 2016.01
RM3270E _51 Engine / Hybrid System _048940 2TR-FE FUEL _0243345 FUEL TANK A

2TR-FE FUEL  FUEL TANK  INSTALLATION  


PROCEDURE

Hide 77213B 1.INSTALL FUEL TANK TO FILLER PIPE HOSE

a.
A350003C01
2.073,1.156 2.208,1.156 2.208,1.156 2.448,0.74 true 0.271,1.135 0.396,1.135 0.396,1.135 0.542,1.01 false 0.094,1.042 0.25,1.24 0.156,0.198 10 false *a 1.885,1.073 2.063,1.271 0.177,0.198 10 false *b 0.563,0.615 0.729,0.813 0.167,0.198 10 true *c 0.927,0.135 1.094,0.302 0.167,0.167 10 true *d 0.135,0.615 0.438,0.854 0.302,0.24 10 true 120°
*a Do not place clamp within this range
*b Paint Mark (White)
*c FR of Vehicle
*d RH of Vehicle


Install the fuel tank to filler pipe hose to the fuel tank assembly, and tighten the clamp to secure the hose.

HINT:

Make sure the hose clamp is oriented as shown in the illustration.



Hide 77020A 2.INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

Hide 3.INSTALL FUEL TANK CUSHION

a.

Install the 3 fuel tank cushions to the fuel tank assembly.


Hide 77697 4.INSTALL NO. 1 FUEL TANK HEAT INSULATOR

a.

Install the No. 1 fuel tank heat insulator with the 4 No. 2 fuel tank brackets.


b.

Install the 2 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 77001A 5.INSTALL FUEL TANK ASSEMBLY

a.

Set the fuel tank assembly on an engine lifter and raise the fuel tank assembly.

NOTICE:

Do not allow the fuel tank assembly to contact the vehicle, especially the differential.



b.
A346215

Connect the clamp and connector.


c.

Fold back approximately half of each cushion so that the wire harness can be installed in the step below.


d.

Attach the wire harness to the 6 clamps and connect the fuel sender gauge assembly connector.

NOTICE:

Be careful not to cut the wire harness.



e.

Install the 3 fuel tank bands with the 3 fuel tank band pins and 3 clips.


f.

Install the 3 fuel tank bands with the 3 bolts.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


Hide 6.CONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A349995C01
0.542,2.344 0.75,2.344 0.75,2.344 1.083,2.688 true 1.26,2.667 1.552,2.365 1.552,2.365 1.677,2.365 true 1.708,2.281 1.865,2.479 0.156,0.198 10 false *a 0.365,2.26 0.542,2.458 0.177,0.198 10 false *b 1.042,3.198 1.219,3.365 0.177,0.167 10 false *c 0.99,1.781 1.156,1.958 0.167,0.177 10 false *d 1.875,2.51 2.073,2.688 0.198,0.177 10 false *e 2.375,2.031 2.531,2.208 0.156,0.177 10 false *f 2.01,3.208 2.26,3.375 0.25,0.167 10 false 35° 2.563,3.156 2.813,3.333 0.25,0.177 10 false 55°
*a Protrusion
*b Paint Mark (Yellow)
*c 0 to 3 mm (0 to 0.118 in.)
*d 2 to 7 mm (0.0787 to 0.276 in.)
*e Top of Vehicle
*f RH of Vehicle


Connect the fuel tank to filler pipe hose to the fuel tank filler pipe sub-assembly, and tighten the clamp to secure the hose.

HINT:

Make sure the hose clamp is oriented as shown in the illustration.



Hide 7.CONNECT FUEL TANK BREATHER HOSE

a.
A349993C01
1.26,0.719 1.5,0.313 1.5,0.313 1.667,0.313 true 1.698,0.24 1.885,0.406 0.188,0.167 10 false *a 3.146,0.698 3.302,0.885 0.156,0.188 10 false *b 2.74,1.146 2.917,1.344 0.177,0.198 10 false *c 1.99,0.875 2.313,1.052 0.323,0.177 10 false 120°
*a Paint Mark
*b Top of Vehicle
*c RH of Vehicle


Connect the fuel tank breather hose to the fuel tank filler pipe sub-assembly, and slide the clamp to secure the hose.

HINT:

Make sure the hose clamp is oriented as shown in the illustration.



Hide 77251B 8.CONNECT FUEL MAIN TUBE AND FUEL RETURN TUBE

a.

Connect the fuel tank main tube sub-assembly and fuel tank return tube, vent line tube.

Click hereEngine / Hybrid System>2TR-FE FUEL>FUEL SYSTEM>PRECAUTION


Hide 77289B 9.INSTALL NO. 3 FUEL TUBE CLAMP

a.

Install the No. 3 fuel tube clamp to the fuel tube.


Hide 77641A 10.INSTALL NO. 1 FUEL TANK PROTECTOR

a.

Install the No. 1 fuel tank protector to the fuel tank assembly with the 5 nuts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 77310A 11.INSTALL FUEL TANK CAP ASSEMBLY

Hide 12.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION