Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › from 2016.01
RM3270E _57 Power Source / Network _041704 NETWORKING _0197846 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2785  Communication Malfunction between ECUs Connected by LIN  


DESCRIPTION

The certification ECU (smart key ECU assembly) intermittently monitors the LIN communication bus between the components related to certification. DTC B2785 is stored when a malfunction in the LIN communication bus between the components related to certification is detected 3 times consecutively.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2785 Communication Malfunction between ECUs Connected by LIN The certification ECU (smart key ECU assembly) detects a malfunction in the LIN communication bus between components related to certification 3 times consecutively.
·

Certification ECU (smart key ECU assembly)

·

Steering lock actuator or upper bracket assembly

·

ID code box (immobiliser code ECU) (w/ ID Code Box [Immobiliser Code ECU])

·

Harness or connector



WIRING DIAGRAM

B301186E14
0.594,1.406 2.719,1.823 2.125,0.417 10 false Certification ECU (Smart Key ECU Assembly) 0.604,1.219 1.063,1.417 0.458,0.198 10 false G16 1.854,0.75 2.313,0.948 0.458,0.198 10 false LIN 2.146,0.583 2.458,0.781 0.313,0.198 10 false 5 5.094,0.74 5.708,0.938 0.615,0.198 10 false LIN1 4.906,0.594 5.063,0.792 0.156,0.198 10 false 2 4.75,1.198 5.208,1.396 0.458,0.198 10 false G138 4.76,1.385 6.354,1.74 1.594,0.354 10 false ID Code Box (Immobiliser Code ECU)* 4.927,2.292 5.083,2.49 0.156,0.198 10 false 5 5.104,2.427 5.563,2.625 0.458,0.198 10 false LIN 4.479,2.865 4.792,3.063 0.313,0.198 10 false G19 4.479,3.042 6.635,3.417 2.156,0.375 10 false Steering Lock Actuator or Upper Bracket Assembly 0.698,3.427 2.594,3.656 1.896,0.229 10 false : LIN Communication Line 0.302,3.083 3.042,3.313 2.74,0.229 10 false *: w/ ID Code Box (Immobiliser Code ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off to troubleshoot:

Connect the GTS to the vehicle, and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

·

If the certification ECU (smart key ECU assembly), ID code box (immobiliser code ECU)* or steering lock actuator or upper bracket assembly is replaced, refer to Service Bulletin.


*: w/ ID Code Box (Immobiliser Code ECU)



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Proceed to
DTC B2785 is not output
DTC B2785 is output



DTC B2785 is not output

DTC B2785 is output

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY OR ID CODE BOX [IMMOBILISER CODE ECU])
3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY OR ID CODE BOX [IMMOBILISER CODE ECU])
a.

Disconnect the G16 certification ECU (smart key ECU assembly) connector.


b.

w/ ID Code Box (Immobiliser Code ECU):

i.

Disconnect the G138 ID code box (w/ ID Code Box [Immobiliser Code ECU]) connector.



c.

Disconnect the G19 steering lock actuator or upper bracket assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

*: w/ ID Code Box (Immobiliser Code ECU)

G16-5 (LIN) - G19-5 (LIN) Always Below 1 Ω
G16-5 (LIN) - G138-2 (LIN1)* Always Below 1 Ω
G16-5 (LIN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CLEAR DTC
a.

Disconnect the G19 steering lock actuator or upper bracket assembly connector.


b.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Proceed to
DTC B2785 is not output
DTC B2785 is output (w/o ID Code Box [Immobiliser Code ECU])
DTC B2785 is output (w/ ID Code Box [Immobiliser Code ECU])



DTC B2785 is not output

6.REPLACE STEERING LOCK ACTUATOR OR UPR BRACKET ASSEMBLY

DTC B2785 is output (w/o ID Code Box [Immobiliser Code ECU])

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

DTC B2785 is output (w/ ID Code Box [Immobiliser Code ECU])

8.CLEAR DTC
6.REPLACE STEERING LOCK ACTUATOR OR UPR BRACKET ASSEMBLY
a.

Replace the steering lock actuator or upper bracket assembly with a new one.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY


b.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Proceed to
DTC B2785 is not output
DTC B2785 is output



DTC B2785 is not output

END (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY IS DEFECTIVE)

DTC B2785 is output

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

8.CLEAR DTC
a.

Disconnect the G138 ID code box (immobiliser code ECU) connector.


b.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Proceed to
DTC B2785 is not output
DTC B2785 is output



DTC B2785 is not output

10.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

DTC B2785 is output

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

10.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU) with a new one.


b.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

11.CHECK FOR DTC
11.CHECK FOR DTC
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Proceed to
DTC B2785 is not output
DTC B2785 is output



DTC B2785 is not output

END (ID CODE BOX [IMMOBILISER CODE ECU] IS DEFECTIVE)

DTC B2785 is output

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)