When the shift lever is in S, the shift range can be changed using the shift paddle switches. It is also possible to select the shift range when the vehicle is being driven with the shift lever in D by operating the shift paddle switches.
Refer to the SRS precaution before troubleshooting.
for Type A:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION
for Type B:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
In accordance with the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Sports Shift Up SW | Sport shift up switch status | OFF or ON | ·
ON: "+" shift paddle operated (up-shift) ·
OFF: "+" shift paddle not operated (up-shift) |
- |
| Sports Shift Down SW | Sport shift down switch status | OFF or ON | ·
ON: "-" shift paddle operated (down-shift) ·
OFF: "-" shift paddle not operated (down-shift) |
- |
| Tester Display |
|---|
| Sports Shift Up SW |
| Sports Shift Down SW |
| Result | Proceed to |
|---|---|
| Data display is within Normal Condition range | A |
| Data display is not within Normal Condition range | B |
A
B
| *a | Rear view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Disconnect the I1 transmission control switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G145-15 (SFTU) - Body ground | "+" shift paddle operated (up-shift) | Below 3 Ω |
| G145-9 (SFTD) - Body ground | "-" shift paddle operated (down-shift) | Below 3 Ω |
| G145-15 (SFTU) - Body ground | "+" shift paddle not operated (up-shift) | 1 MΩ or higher |
| G145-9 (SFTD) - Body ground | "-" shift paddle not operated (down-shift) | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Spiral Cable with Sensor Sub-assembly) |
Disconnect the spiral cable with sensor sub-assembly connector.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G4-2 (ECC) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G145 ECM connector.
Disconnect the G4 spiral cable with sensor sub-assembly connector.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G145-9 (SFTD) - G4-7 (SDN) | Always | Below 1 Ω |
| G145-15 (SFTU) - G4-14 (SUP) | Always | Below 1 Ω |
| G145-9 (SFTD) or G4-7 (SDN) - Body ground | Always | 10 kΩ or higher |
| G145-15 (SFTU) or G4-14 (SUP) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Steering Pad Switch Assembly Connector
(to Spiral Cable with Sensor Sub-assembly) |
Disconnect the steering pad switch connector.
Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z2-6 (SUP) - z2-7 (ECC) | "+" shift paddle operated (up-shift) | Below 3 Ω |
| z2-12 (SDN) - z2-7 (ECC) | "-" shift paddle operated (down-shift) | Below 3 Ω |
| z2-6 (SUP) - z2-7 (ECC) | "+" shift paddle not operated (up-shift) | 1 MΩ or higher |
| z2-12 (SDN) - z2-7 (ECC) | "-" shift paddle not operated (down-shift) | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the spiral cable with sensor sub-assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Shift Paddle Switch LH |
Remove the shift paddle switch LH.
Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>SHIFT PADDLE SWITCH>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| SDN - ECC | "-" shift paddle operated (down-shift) | Below 3 Ω |
| SDN - ECC1 | "-" shift paddle operated (down-shift) | Below 3 Ω |
| SDN - ECC | "-" shift paddle not operated (down-shift) | 1 MΩ or higher |
| SDN - ECC1 | "-" shift paddle not operated (down-shift) | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Shift Paddle Switch RH |
Remove the shift paddle switch RH.
Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>SHIFT PADDLE SWITCH>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| SUP - ECC1 | "+" shift paddle operated (up-shift) | Below 3 Ω |
| SUP - ECC1 | "+" shift paddle not operated (up-shift) | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Steering Pad Switch Assembly) |
Disconnect the No. 1 switch wire connector.
Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>SHIFT PADDLE SWITCH>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| SUP - ECC | "+" shift paddle operated (up-shift) | Below 3 Ω |
| SDN - ECC | "-" shift paddle operated (down-shift) | Below 3 Ω |
| SUP - ECC | "+" shift paddle not operated (up-shift) | 1 MΩ or higher |
| SDN - ECC | "-" shift paddle not operated (down-shift) | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG