The air conditioning harness assembly connects the air conditioning amplifier assembly and the servo motors. The air conditioning amplifier assembly supplies power and sends operation instructions to each servo motor through the air conditioning harness assembly. Each servo motor sends damper position information to the air conditioning amplifier assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | Note |
|---|---|---|---|---|---|
| B1497/97 | BUS IC Communication Malfunction | Error or open in communication line | ·
Harness or connector ·
No. 1 air conditioning radiator damper servo sub-assembly (front side air mix), (front mode) ·
No. 1 blower damper servo sub-assembly ·
Air conditioning harness assembly ·
Air conditioning amplifier assembly |
Memorized (10 seconds or more) | - |
The air conditioning amplifier assembly stores the DTC of the respective malfunction if it has occurred for the period of time indicated in the parentheses.
Inspect the fuses for circuits related to this system before performing the following procedure.
When the servo motor or air conditioning amplifier assembly is replaced, be sure to perform servo motor initialization.
Clear the DTCs.
Check for DTCs.
DTC B1497/97 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
| *a | Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
Disconnect the air conditioning amplifier assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G37-14 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G37-21 (B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Air Conditioner / Active Test.
Check the operation by referring to the table below.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Air Mix Servo Targ Pulse(D) | No. 1 air conditioning radiator damper servo sub-assembly (front side air mix) target pulse | Min.: 128
Max.: 383 |
·
Operates between 165 and 257 pulses (for LHD) ·
Operates between 255 and 347 pulses (for RHD) |
| Air Outlet Servo Pulse (D) | No. 1 air conditioning radiator damper servo sub-assembly (front mode) pulse | Min.: 128
Max.: 383 |
·
Operates between 143 and 257 pulses (for LHD) ·
Operates between 255 to 369 pulses (for RHD) |
| Air Inlet Damper Targ Pulse | No. 1 blower damper servo sub-assembly (recirculation) target pulse | Min.: 128
Max.: 383 |
Operates between 235 and 258 pulses |
| Tester Display |
|---|
| Air Mix Servo Targ Pulse(D) |
| Tester Display |
|---|
| Air Outlet Servo Pulse (D) |
| Tester Display |
|---|
| Air Inlet Damper Targ Pulse |
Arm of the damper servo motor selected in the Active Test moves smoothly.
According to the test result, proceed to the next step.
| Result | Proceed to |
|---|---|
| No. 1 air conditioning radiator damper servo sub-assembly (front side air mix) is malfunctioning | A |
| No. 1 air conditioning radiator damper servo sub-assembly (front mode) is malfunctioning | |
| No. 1 blower damper servo sub-assembly is malfunctioning | B |
A
B
Replace the No. 1 air conditioning radiator damper servo sub-assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT AIR CONDITIONING UNIT>DISASSEMBLY
Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.
Clear the DTCs.
Check for DTCs.
DTC B1497/97 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the air conditioning harness assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT AIR CONDITIONING UNIT>DISASSEMBLY
Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or known good one and check that the condition returns to normal.
Clear the DTCs.
Check for DTCs.
DTC B1497/97 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the No. 1 blower damper servo sub-assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>BLOWER UNIT>DISASSEMBLY
Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.
Clear the DTCs.
Check for DTCs.
DTC B1497/97 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG