Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB › from 2016.01
RM3270E _52 Drivetrain _041686 AXLE AND DIFFERENTIAL _0195329 FRONT AXLE HUB A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.INSTALL PLUG (for Pre-Runner)

a.
C119749N01
1.875,1.438 2.438,1.479 2.438,1.479 1.76,1.115 true 2.458,1.385 2.76,1.531 0.302,0.146 10 SST

Using SST and a hammer, install a new plug.

SST
09950-60010  (09951-00450)
09950-70010  (09951-07100)


Hide 43502F 2.INSTALL FRONT AXLE HUB OIL SEAL LH

a.
F042762

Using a brass bar and hammer, tap in a new front axle hub oil seal LH.


Hide 43502M 3.INSTALL FRONT AXLE HUB INNER BEARING LH (for 4WD)

a.
C325047N01
0.479,1.771 0.948,1.948 false 0.177,1.667 0.635,1.865 0.458,0.198 10 false SST

Using SST and a press, press a new front axle hub inner bearing LH into the front axle hub sub-assembly LH.

SST
09649-17010  

NOTICE:

Insert 4 bolts into the bearing before installing the bearing to the front axle hub sub-assembly LH.



Hide 43502M 4.INSTALL FRONT AXLE HUB INNER BEARING LH (for Pre-Runner)

a.
C325048N01
0.51,1.74 0.958,1.917 false 0.188,1.625 0.646,1.823 0.458,0.198 10 false SST

Using SST and a press, press a new front axle hub inner bearing LH into the front axle hub sub-assembly LH.

SST
09649-17010  

NOTICE:

Insert 4 bolts into the bearing before installing the bearing to the front axle hub sub-assembly LH.



b.
C324916N01
1.125,2.448 0.563,2.052 true 0.229,1.948 0.688,2.146 0.458,0.198 10 false SST

Using SST, install a new adjusting nut.

SST
09607-26010  

Torque:
274 N*m (2794 kgf*cm, 202 ft.*lbf)


c.
C324915N03
1.615,1.115 2.094,1.115 true 2.229,1.021 2.688,1.219 0.458,0.198 10 false SST

Using SST and a hammer, stake the adjusting nut.

SST
09930-00010  


Hide 43502C 5.INSTALL FRONT AXLE HUB SUB-ASSEMBLY LH (for 4WD)

C328308C01
2.875,1.271 3.188,1.469 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length


a.

Apply MP grease to a new O-ring.


b.

Install the O-ring to the axle hub.


c.

Install the dust cover and front axle hub sub-assembly LH to the steering knuckle LH with the 4 bolts.

Torque:
Specified tightening torque : 80 N*m (816 kgf*cm, 59 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a ball joint lock nut wrench (fulcrum length of 149 mm (5.866 in.)) + torque wrench (fulcrum length of 380 mm (14.961 in.)): 57.5 N*m (586 kgf*cm, 42 ft.*lbf).




Hide 43502C 6.INSTALL FRONT AXLE HUB SUB-ASSEMBLY LH (for Pre-Runner)

a.
C328309C01
2.896,1.25 3.208,1.448 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length


Apply MP grease to a new O-ring.


b.

Install the O-ring to the axle hub.


c.

Install the dust cover and front axle hub sub-assembly LH to the steering knuckle LH with the 4 bolts.

Torque:
Specified tightening torque : 80 N*m (816 kgf*cm, 59 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a ball joint lock nut wrench (fulcrum length of 149 mm (5.866 in.)) + torque wrench (fulcrum length of 380 mm (14.961 in.)): 57.5 N*m (586 kgf*cm, 42 ft.*lbf).




Hide 43502H 7.INSTALL FRONT AXLE SHAFT NUT LH (for 4WD)

C324911

a.

Clean the threaded parts on the drive shaft and front axle shaft nut LH using a non-residue solvent.


b.

Install the front axle shaft nut LH.

Torque:
235 N*m (2396 kgf*cm, 173 ft.*lbf)


c.

Install the adjusting cap and a new cotter pin.

NOTICE:

If the holes for the cotter pin are not aligned, tighten the nut an additional 60°.



Hide 43514C 8.INSTALL FRONT AXLE HUB GREASE CAP LH (for 4WD)

a.

Install a new front axle hub grease cap LH to the front axle hub sub-assembly LH.


Hide 43512 9.INSTALL FRONT DISC

Hide 47750 10.CONNECT FRONT DISC BRAKE CYLINDER ASSEMBLY LH

Hide 89543 11.CONNECT FRONT SPEED SENSOR LH

Hide 12.INSTALL FRONT WHEEL