Home › Drivetrain › RC60 / RC61 MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSMISSION SYSTEM › from 2016.01
RM3270E _52 Drivetrain _048961 RC60 / RC61 MANUAL TRANSMISSION / TRANSAXLE _0242079 MANUAL TRANSMISSION SYSTEM J

RC60 / RC61 MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION SYSTEM  Pattern Select Switch iMT Mode Circuit  


DESCRIPTION

Operating the iMT switch illuminates the iMT indicator light in the combination meter. This displays the iMT system standby condition.

WIRING DIAGRAM

C325752E10
5.219,0.75 5.833,0.948 0.615,0.198 10 false MTMS 5,0.75 5.281,0.948 0.281,0.198 10 false 8 3.75,0.75 4.365,0.948 0.615,0.198 10 false 6 3.5,0.75 3.667,1 0.167,0.25 10 false S 2.719,0.75 3.333,0.948 0.615,0.198 10 false E 2.5,0.75 2.698,0.948 0.198,0.198 10 false 2 2.833,1.302 3.448,1.5 0.615,0.198 10 false I5 2.833,1.5 3.583,1.667 0.75,0.167 10 false iMT Switch 0.469,3.219 2.167,3.417 1.698,0.198 10 false : CAN Communication Line 2.333,3 4.198,3.25 1.865,0.25 10 false Combination Meter Assembly 5.667,3 6.281,3.198 0.615,0.198 10 false G49 5.667,3.167 6.281,3.365 0.615,0.198 10 false ECM 5.917,0.438 6.531,0.635 0.615,0.198 10 false 12 V

PROCEDURE

1.READ VALUE USING GTS (IMT SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List


e.

According to the display on the GTS, read the Data List.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
iMT Switch iMT switch status ON or OFF
·

ON: iMT switch being pressed and held

·

OFF: iMT switch not pressed


-
Powertrain > Engine > Data List
Tester Display
iMT Switch
50003 234 1086

Result:
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.CHECK HARNESS AND CONNECTOR (IMT SWITCH - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (IMT SWITCH - BODY GROUND)
a.
C323648C01
0.177,0.885 0.708,1.188 0.531,0.302 1.031,1.771 1.281,1.354 true 0.958,1.792 1.115,1.99 0.156,0.198 10 false E 0.375,0.958 0.635,1.156 0.26,0.198 10 false I5 0.208,0.177 0.51,0.385 0.302,0.208 10 false *a
*a Front view of wire harness connector
(to iMT Switch)


Disconnect the transmission revolution sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I5-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (IMT SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (IMT SWITCH - ECM)
a.

Disconnect the iMT switch connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I5-6 (S) - G49-8 (MTMS) Always Below 1 Ω
I5-6 (S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT IMT SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT IMT SWITCH

OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG