Home › Vehicle Exterior › WIPER / WASHER › WIPER SWITCH › from 2016.01
RM3270E _59 Vehicle Exterior _041719 WIPER / WASHER _0213518 WIPER SWITCH A

WIPER / WASHER  WIPER SWITCH  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the windshield wiper switch assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal w/ Power Back Door System:
Reset back door close position
Power back door system (Click here)

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for RHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

for Type A:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION

for Type B:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 45287 3.REMOVE LOWER STEERING COLUMN COVER

NOTICE:

If the removal procedures are followed incorrectly, the part may become damaged.


a.

Release the tilt and telescopic lever, and fully extend and lower the steering column assembly.

NOTICE:

Before operating the tilt and telescopic lever, make note of the current steering position.



b.
B427700C01
0.083,0.042 0.396,0.198 0.313,0.156 10 false *A 0.135,2.552 0.448,2.708 0.313,0.156 10 false *B
*A w/ Entry and Start System
*B w/o Entry and Start System


With the steering wheel assembly facing straight ahead, turn the steering wheel 90° to the right and remove the screw shown in the illustration.


c.
B427701C01
0.115,0.052 0.427,0.208 0.313,0.156 10 false *A 0.125,2.51 0.438,2.667 0.313,0.156 10 false *B
*A w/ Entry and Start System
*B w/o Entry and Start System


With the steering wheel assembly facing straight ahead, turn the steering wheel 90° to the left and remove the screw shown in the illustration.


d.
B427702C01
0.115,0.052 0.427,0.208 0.313,0.156 10 false *A 0.104,2.479 0.417,2.635 0.313,0.156 10 false *B
*A w/ Entry and Start System
*B w/o Entry and Start System


Remove the screw.


e.
B427703C01
0.167,0.146 0.479,0.302 0.313,0.156 10 false *A 0.167,2.521 0.479,2.677 0.313,0.156 10 false *B
*A w/ Entry and Start System
*B w/o Entry and Start System


Press on the left and right sides of the lower steering column cover to detach the claw.


f.
B427704C01
0.177,0.073 0.49,0.229 0.313,0.156 10 false *A 0.156,2.5 0.469,2.656 0.313,0.156 10 false *B
*A w/ Entry and Start System
*B w/o Entry and Start System
V113147

Remove in this Direction


Detach the claw and remove the lower steering column cover.


Hide 45286B 4.REMOVE UPPER STEERING COLUMN COVER

a.
B407649C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claw and remove the upper steering column cover from steering column assembly.


Hide 84650 5.REMOVE WINDSHIELD WIPER SWITCH ASSEMBLY

B407650

a.

Disconnect the 2 connectors.


b.
B407651C01
0,0 0,0 false
V100155

Protective Tape
V113147

Remove in this Direction


Using a screwdriver, detach the claw and remove the windshield wiper switch assembly as shown in the illustration.

NOTICE:

Do not damage the claw.


HINT:

Tape the screwdriver tip before use.