Home › Engine / Hybrid System › 2KD-FTV STARTING › STARTER(for 2.0 kW Type) › from 2016.01
RM3270E _51 Engine / Hybrid System _048937 2KD-FTV STARTING _0244701 STARTER(for 2.0 kW Type) G

2KD-FTV STARTING  STARTER(for 2.0 kW Type)  INSPECTION  


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

CAUTION:

As a large electric current passes through the cable during this inspection, a thick cable must be used. Otherwise, the cable may become hot and cause injury.


NOTICE:

These tests must be performed within 3 to 5 seconds to prevent the coil from burning out.


a.

Mount the starter assembly in a vise between aluminum plates.


b.

Perform a pull-in test.

i.
A351630C01
2.385,1.448 2.604,0.958 2.604,0.958 2.906,0.958 true 1.073,0.854 1.51,0.854 1.51,0.854 2.156,1.51 true 0.833,0.771 1.146,0.969 0.313,0.198 10 false *b 2.979,0.875 3.292,1.073 0.313,0.198 10 false *a
*a Terminal C
*b Terminal 50


Remove the nut and disconnect the lead wire from terminal C.


ii.

Connect the battery to the starter assembly as shown in the illustration. Check that the clutch pinion gear extends.

If the clutch pinion gear does not extend, replace the magnet starter switch assembly.



c.

Perform a holding test.

i.
A351631C01
0,0 0,0 false
V100135

Disconnect


Disconnect the negative (-) lead from terminal C with the condition specified in the pull-in test above being maintained. Check that the clutch pinion gear remains out.

If the clutch pinion gear returns inward, replace the magnet starter switch assembly.



d.

Inspect the clutch pinion gear return.

i.
A351632C01
0,0 0,0 false
V100135

Disconnect
V100136

Return Inward


Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.

If the clutch pinion gear does not return inward, replace the magnet starter switch assembly.



e.

Perform an operation test without load.

i.

Connect the lead wire to terminal C with the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


ii.
A351633C02
1.083,0.729 1.427,0.729 1.427,0.729 2.167,1.385 true 2.385,1.156 2.542,0.469 2.542,0.469 2.813,0.469 true 2.75,2.552 2.875,2.792 2.875,2.792 3.052,2.792 true 2.875,0.385 3.188,0.583 0.313,0.198 10 false *a 0.854,0.635 1.167,0.833 0.313,0.198 10 false *b 3.104,2.708 3.313,2.896 0.208,0.188 10 false *c
*a Terminal 30
*b Terminal 50
*c AC/DC 400A Probe


Connect the battery and an ammeter (AC/DC 400A probe) to the starter assembly as shown in the illustration.


iii.

Check that the starter rotates smoothly and steadily while the clutch pinion gear is extended. Then measure the current.

Standard current:

150 A or less at 11.5 V


If the result is not as specified, replace the starter assembly.



Hide 28150 2.INSPECT MAGNET STARTER SWITCH ASSEMBLY

a.
A300398

Push in the plunger and check that it returns quickly to its original position.

If the result is not as specified, replace the magnet starter switch assembly.


b.
A341259C01
1.469,1.813 1.635,1.813 1.635,1.813 1.802,1.396 false 2.115,0.927 2.448,0.51 2.448,0.51 2.615,0.51 false 1.333,0.75 1.667,0.333 1.667,0.333 1.833,0.333 true 1.292,1.729 1.604,1.927 0.313,0.198 10 false *a 2.688,0.427 3,0.625 0.313,0.198 10 false *b 1.896,0.25 2.208,0.448 0.313,0.198 10 false *c
*a Terminal C
*b Terminal 50
*c Switch Body


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Terminal C Always Below 1 Ω
Terminal 50 - Switch Body Below 2 Ω


If the result is not as specified, replace the magnet starter switch assembly.


Hide 28140 3.INSPECT STARTER BRUSH HOLDER ASSEMBLY

a.

Check the resistance.

i.
A372882N01
0.5,0.74 1.271,0.948 true 0.573,2.031 1.125,1.677 false 1.417,2.76 1.781,2.49 false 2.292,3.604 2.698,3.604 false 1.76,4.198 1.115,3.698 false 0.365,0.677 0.521,0.875 0.156,0.198 10 false A 0.417,2.031 0.573,2.229 0.156,0.198 10 false B 1.854,2.406 2.01,2.604 0.156,0.198 10 false C 2.792,3.552 2.948,3.75 0.156,0.198 10 false D 1.844,4.177 2,4.375 0.156,0.198 10 false E

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A - B
C - D
D - E
Always Below 1 Ω


If the result is not as specified, replace the starter brush holder assembly.



b.
A372727C02
2.385,1.135 2.698,1.333 0.313,0.198 10 false *a
*a Length


Check the brush length.

i.

Using a vernier caliper, measure the brush length.

Standard length:

10.4 mm (0.409 in.)


Minimum length:

5.0 mm (0.197 in.)


If the length is less than the minimum, replace the starter brush holder assembly.



Hide 28160 4.INSPECT STARTER ARMATURE ASSEMBLY

a.

Check the commutator surface for dirt and burns.

If the surface is dirty or burnt, replace the starter armature assembly.


b.

Check the resistance.

i.
A341258C01
2.042,1.25 2.375,1.667 2.375,1.667 2.542,1.667 true 1.5,1 1,1.417 1,1.417 0.833,1.417 true 2.604,1.552 2.917,1.75 0.313,0.198 10 false *a 0.656,1.323 0.969,1.521 0.313,0.198 10 false *b
*a Segment
*b Coil Core


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω
Segment - Coil Core 10 kΩ or higher


If the result is not as specified, replace the starter armature assembly.



c.

Check the commutator for circle runout.

i.
A122067

Place the commutator on V-blocks.


ii.

Using a dial indicator, measure the circle runout.

Maximum runout:

0.05 mm (0.00196 in.)


If the runout is more than the maximum, replace the starter armature assembly.



d.

Check the commutator.

i.
A300395

Using a vernier caliper, measure the commutator diameter.

Standard diameter:

29.0 mm (1.14 in.)


Minimum diameter:

28.0 mm (1.10 in.)


HINT:

Be sure to measure the commutator diameter at the ridges.


If the diameter is less than the minimum, replace the starter armature assembly.


ii.
A102634

Using a vernier caliper, measure the undercut depth of the commutator.

Standard undercut depth:

0.7 mm (0.0276 in.)


Minimum undercut depth:

0.4 mm (0.0157 in.)


HINT:

Be sure to measure the commutator diameter at the ridges.


If the undercut depth is less than the minimum, replace the starter armature assembly.



Hide 5.INSPECT STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.

Check the clutch pinion gear teeth for wear or damage.

If the clutch pinion gear teeth are damaged, replace the repair service starter kit and also inspect the flywheel ring gear for wear or damage.


b.
A356505C01
0,0 0,0 false
V100135

Free
V100136

Lock


Rotate the clutch pinion gear clockwise and check that it turns freely. Try to rotate the clutch pinion gear counterclockwise and check that it locks.

If the result is not as specified, replace the repair service starter kit.