The main power source for the body ECU is supplied via the door control battery.
If the body ECU has been replaced, it is necessary to initialize the body ECU.*
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
As the door control battery is installed between the vehicle battery and body ECU, first perform the inspections to confirm that there are no malfunctions in the power source circuit for the body ECU before performing this troubleshooting procedure.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION
Inspect the fuses for circuits related to this system before performing the following procedure.
*: w/ Automatic Light Control System
| *a | Front view of wire harness connector
(to Door Control Battery) |
Disconnect the door control battery connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N49-4 (BECU) - Body ground | Always | 11 to 14 V |
| N49-5 (BATB) - Body ground | Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N49-2 (GND1) - Body ground | Always | Below 1 Ω |
| N49-10 (GND2) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N49 door control battery connector.
Disconnect the 2J instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N49-3 (EDOR) - 2J-3 (BECU) | Always | Below 1 Ω |
| N49-3 (EDOR) or 2J-3 (BECU) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
for LHD:Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD:Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the body ECU from the instrument panel junction block assembly.
for LHD:Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD:Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-6 (BECU) - 2J-3 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD:Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD:Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
Turn the ignition switch off.
Remove the ECU-B NO.4 fuse from the engine room relay block.
Leave the vehicle as is for 30 minutes (wait until the door control battery is discharged).
Discharge time is reduced when the door control battery is not fully charged.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| N49-3 (EDOR) - Body ground | Ignition switch off | Below 2 V |
Install the ECU-B NO.4 fuse to the engine room relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| N49-3 (EDOR) - Body ground | Ignition switch off | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD:Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD:Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
NG