Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › from 2016.01
RM3270E _51 Engine / Hybrid System _041679 CRUISE CONTROL _0199359 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  Clutch Switch Circuit  


DESCRIPTION

While depressing the clutch pedal, the clutch switch sends a signal to terminal D of the ECM. The ECM cancels cruise control when terminal D receives the signal.

WIRING DIAGRAM

C330947E02
1.427,0.052 2.479,0.281 1.052,0.229 10 false from IG Circuit 2.875,1 3.042,1.167 0.167,0.167 10 false 1 4.021,0.99 4.24,1.219 0.219,0.229 10 false 2 2.698,1.667 4.5,1.896 1.802,0.229 10 false Clutch Switch Assembly 2.708,1.5 3.042,1.667 0.333,0.167 10 false B1 1.333,1.333 2.083,1.5 0.75,0.167 10 false IG1 NO. 4 5.354,1.125 5.74,1.354 0.385,0.229 10 false C38 5.677,1.125 6.063,1.354 0.385,0.229 10 false G142 5.406,0.875 5.708,1.021 0.302,0.146 10 false 14 5.76,0.875 6.094,1.021 0.333,0.146 10 false 18 5.365,1.365 5.75,1.594 0.385,0.229 10 false *1 5.76,1.365 6.146,1.594 0.385,0.229 10 false *2 6.104,1.135 6.521,1.302 0.417,0.167 10 false D 6.313,2.438 6.813,2.75 0.5,0.313 10 false ECM 0.427,2.781 2.25,2.99 1.823,0.208 10 false *1: for 1GD-FTV, 2GD-FTV 0.427,3.198 1.479,3.427 1.052,0.229 10 false *2: for 2TR-FE

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT CLUTCH SWITCH ASSEMBLY
a.

Remove the clutch switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>REMOVAL


b.

Inspect the clutch switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CLUTCH SWITCH ASSEMBLY - BATTERY)

NG

REPLACE CLUTCH SWITCH ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (CLUTCH SWITCH ASSEMBLY - BATTERY)
a.
C326224C07
1.458,0.25 1.917,0.552 0.458,0.302 1.615,0.323 1.927,0.521 0.313,0.198 10 false B1 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Clutch Switch Assembly)


Disconnect the clutch switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B1-1 - Body ground Ignition Switch ON 11 to 14 V
B1-1 - Body ground Ignition Switch off Below 1 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CLUTCH SWITCH ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CLUTCH SWITCH ASSEMBLY - ECM)
a.

for 1GD-FTV, 2GD-FTV

i.

Disconnect the B1 clutch switch assembly connector.


ii.

Disconnect the C38 ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B1-2 - C38-14 (D) Always Below 1 Ω
B1-2 or C38-14 (D) - Body ground Always 10 kΩ or higher




b.

for 2TR-FE

i.

Disconnect the B1 clutch switch assembly connector.


ii.

Disconnect the G142 ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B1-2 - G142-18 (D) Always Below 1 Ω
B1-2 or G142-18 (D) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR