Home › Vehicle Interior › INTERIOR PANELS / TRIM › UPPER INSTRUMENT PANEL › from 2016.01
RM3270E _58 Vehicle Interior _041715 INTERIOR PANELS / TRIM _0213628 UPPER INSTRUMENT PANEL A

INTERIOR PANELS / TRIM  UPPER INSTRUMENT PANEL  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for RHD vehicles.



The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the upper instrument panel removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal w/ Power Back Door System:
Reset back door close position
Power door lock control system (Click here)

CAUTION:
B410192

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


PROCEDURE

Hide 1. TABLE OF BOLT, SCREW, NUT AND CLIP

HINT:

All bolts, screws and clips relevant to installing and removing the instrument panel are shown along with their alphabetic code in the table below.


B410194E01
5.688,2.25 7.115,2.448 1.427,0.198 10 false mm (in.) (L = Length) 0.156,0.156 0.604,0.354 0.448,0.198 10 false Code 2.469,0.146 2.917,0.344 0.448,0.198 10 false Code 4.792,0.146 5.24,0.344 0.448,0.198 10 false Code 1.198,0.146 1.75,0.344 0.552,0.198 10 false Shape 3.552,0.146 4.104,0.344 0.552,0.198 10 false Shape 5.844,0.135 6.396,0.333 0.552,0.198 10 false Shape 0.188,1.229 0.646,1.427 0.458,0.198 10 false <A> 2.5,1.229 2.958,1.427 0.458,0.198 10 false <B> 4.823,1.229 5.281,1.427 0.458,0.198 10 false <C> 6.375,0.74 6.74,0.938 0.365,0.198 10 false φ 5 4.146,0.729 4.51,0.927 0.365,0.198 10 false φ 8 4.125,0.948 4.688,1.156 0.563,0.208 10 false (0.315) 4.125,1.375 4.615,1.573 0.49,0.198 10 false L=18 4.104,1.594 4.615,1.792 0.51,0.198 10 false (0.709) 6.344,0.958 6.948,1.156 0.604,0.198 10 false (0.197) 6.354,1.438 6.771,1.635 0.417,0.198 10 false L=14 6.323,1.615 6.906,1.813 0.583,0.198 10 false (0.551)

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 45100 4.REMOVE STEERING WHEEL ASSEMBLY

Hide 55667 5.REMOVE INSTRUMENT PANEL REGISTER BEZEL GARNISH

a.
B409717C01
1.073,0.781 0.948,0.333 true 0.833,0.198 1.052,0.354 0.219,0.156 10 true *a
*a Protective Tape


Put protective tape around the instrument panel register bezel garnish.


b.
B409719C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the claw and remove the instrument panel register bezel garnish.


Hide 55011A 6.REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

a.
B409720C01
1.75,0.5 2.271,0.354 true 2.219,0.24 2.448,0.417 0.229,0.177 10 true *a
*a Protective Tape


Put protective tape around the No. 1 instrument panel garnish sub-assembly.


b.
B409722C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction
V100135

Order of Removal


Place your hands at the position shown in the illustration and pull as shown to detach the clip and remove the No. 1 instrument panel garnish sub-assembly.


Hide 55012A 7.REMOVE NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

a.
B409723C01
1.104,0.344 1.604,0.469 true 1.01,0.26 1.229,0.417 0.219,0.156 10 true *a
*a Protective Tape


Put protective tape around the No. 2 instrument panel garnish sub-assembly.


b.
B409725C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction
V100135

Order of Removal


Place your hands at the position shown in the illustration and pull as shown to detach the clip and remove the No. 2 instrument panel garnish sub-assembly.


Hide 55410C 8.REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

a.
B409726C01
2.458,0.729 2.844,0.573 true 2.844,0.448 3.073,0.604 0.229,0.156 10 true *a
*a Protective Tape


Put protective tape around the instrument cluster finish panel assembly.


b.
B409728C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction
V100135

Order of Removal


Place your hands at the position shown in the illustration and pull as shown to detach the clip and remove the instrument cluster finish panel assembly.


Hide 83100 9.REMOVE COMBINATION METER ASSEMBLY

Hide 55041B 10.REMOVE NO. 1 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY

a.
B409730C01
1.323,0.646 1.188,0.25 true 1.083,0.177 1.292,0.333 0.208,0.156 10 true *a
*a Protective Tape


Put protective tape around the No. 1 instrument panel box door sub-assembly.


b.

Open the glove compartment door assembly.


c.
B409732C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the clip and remove the No. 1 instrument panel box door sub-assembly.


Hide 55405B 11.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

a.

for Type A:

i.
B443107C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the clip and remove the center instrument cluster finish panel sub-assembly.



b.

for Type B:

i.
B409747C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the clip and remove the center instrument cluster finish panel sub-assembly.



Hide 67913B 12.REMOVE FRONT DOOR SCUFF PLATE RH

Hide 62111C 13.REMOVE COWL SIDE TRIM BOARD RH

B404626C01
0.313,0.729 0.521,0.885 0.208,0.156 10 true *a
*a Cap Nut
V113146

Place Hands Here
V113147

Remove in this Direction


a.

Remove the cap nut.


b.

Place your hands at the position shown in the illustration and pull as shown to detach the clip and remove the cowl side trim board RH.


Hide 55317A 14.REMOVE INSTRUMENT SIDE PANEL RH

a.
B409781C01
1.146,1.021 1.375,1.177 0.229,0.156 10 true *1
*1 Front Door Opening Trim Weatherstrip RH


Disconnect the front door opening trim weatherstrip RH in the range shown in the illustration.


b.
B409736C01
1.229,0.448 1.698,0.635 true 1.021,0.302 1.25,0.479 0.229,0.177 10 true *a
*a Protective Tape


Put protective tape around the instrument side panel RH.


c.
B409738C01
0,0 0,0 false
V113146

Insert Moulding Remover A Here
V113147

Remove in this Direction


Insert moulding remover A at the position shown in the illustration and pull as shown to detach the claw and guide and remove the instrument side panel RH.


Hide 67914B 15.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 62112 16.REMOVE COWL SIDE TRIM BOARD LH

a.
B404623C01
2.927,0.76 3.156,0.917 0.229,0.156 10 true *a
*a Cap Nut
V113146

Place Hands Here
V113147

Remove in this Direction


Remove the cap nut.


b.

Place your hands at the position shown in the illustration and pull as shown to detach the clip and remove the cowl side trim board LH.


Hide 55318C 17.REMOVE INSTRUMENT SIDE PANEL LH

a.
B409780C01
1.938,1.083 2.156,1.24 0.219,0.156 10 true *1
*1 Front Door Opening Trim Weatherstrip LH


Disconnect the front door opening trim weatherstrip LH in the range shown in the illustration.


b.
B409733C01
1.75,0.667 2.24,0.531 true 2.25,0.406 2.479,0.563 0.229,0.156 10 true *a
*a Protective Tape


Put protective tape around the instrument side panel LH.


c.
B409735C01
0,0 0,0 false
V113146

Insert Moulding Remover A Here
V113147

Remove in this Direction


Insert moulding remover A at the position shown in the illustration and pull as shown to detach the claw and guide.


d.

Disconnect the connector and remove the instrument side panel LH.


Hide 74603 18.REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY

HINT:

Use the same procedure for both front assist grip assemblies.


a.
B404468C01
0.833,1.594 1.156,1.063 true 0.708,1.594 0.927,1.75 0.219,0.156 10 true *a
*a Protective Tape


Put protective tape around the assist grip covers.


b.
B404469C01
0.74,0.979 1.208,1.094 true 0.583,0.875 0.781,1.031 0.198,0.156 10 true *a
*a Protective Tape
V113146

Insert Thin-bladed Screwdriver Here


Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and open the assist grip covers.

HINT:

Tape the thin-bladed screwdriver tip before use.



c.
B404470

Remove the 2 bolts and front assist grip sub-assembly.


Hide 62212 19.REMOVE FRONT PILLAR GARNISH LH

a.
B409739C01
2.531,1.625 2.063,1.302 true 2.521,1.573 2.729,1.74 0.208,0.167 10 true *a
*a Protective Tape


Put protective tape around the front pillar garnish LH.


b.
B409740C01
0.479,1.167 0.792,1.323 0.313,0.156 10 false *1
*1 Front Door Opening Trim Weatherstrip LH


Disconnect the front door opening trim weatherstrip LH in the range shown in the illustration.


c.
B409741C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Place your hands at the position shown in the illustration and pull as shown to detach the clip and guide and remove the front pillar garnish LH.


d.

w/ Curtain Shield Airbag:

Protect the curtain shield airbag assembly LH.

i.
B405232C01
0.948,2.094 1.313,1.75 true 2.156,1.917 2.594,1.677 true 1.667,1.198 2.021,0.885 true 2.583,1.552 2.813,1.708 0.229,0.156 10 true *a 1.979,0.771 2.188,0.927 0.208,0.156 10 true *b 0.802,2.063 1.01,2.219 0.208,0.156 10 true *b
*a Protective Cover
*b Adhesive Tape


Completely cover the curtain shield airbag assembly LH with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.

NOTICE:

Cover the curtain shield airbag assembly LH with a protective cover as soon as the front pillar garnish LH is removed.




Hide 62211 20.REMOVE FRONT PILLAR GARNISH RH

a.
B409743C01
0.76,1.635 1.271,1.333 true 0.573,1.583 0.792,1.74 0.219,0.156 10 true *a
*a Protective Tape


Put protective tape around the front pillar garnish RH.


b.
B409744C01
2.979,1.292 3.208,1.448 0.229,0.156 10 false *1
*1 Front Door Opening Trim Weatherstrip RH


Disconnect the front door opening trim weatherstrip RH in the range shown in the illustration.


c.
B409745C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Place your hands at the position shown in the illustration and pull as shown to detach the clip and guide and remove the front pillar garnish RH.


d.

w/ Curtain Shield Airbag:

Protect the curtain shield airbag assembly RH.

i.
B405233C01
1.333,1.583 0.885,1.083 true 2.167,2.385 1.719,1.885 true 2.677,2.198 2.219,1.792 true 2.188,2.427 2.5,2.583 0.313,0.156 10 false *a 2.719,2.198 3.031,2.354 0.313,0.156 10 false *b 0.74,0.948 0.958,1.104 0.219,0.156 10 true *b
*a Protective Cover
*b Adhesive Tape


Completely cover the curtain shield airbag assembly RH with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.

NOTICE:

Cover the curtain shield airbag assembly RH with a protective cover as soon as the front pillar garnish RH is removed.




Hide 55302A 21.REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY

a.
B339324C07
0.74,0.917 0.99,0.427 true 0.969,0.281 1.281,0.438 0.313,0.156 10 false *a
*a Lock Slider


Pull and slide the lock slider as shown to release the connector lock and disconnect the passenger airbag connector.

NOTICE:

When handling the passenger airbag connector, take care not to damage the airbag wire harness.



b.

Disconnect the connector and detach the clamp.


c.

Remove the 2 clips <A>.


d.

Remove the passenger airbag installation bolt <B>.

B409751C01
2.156,2.719 2.385,2.875 0.229,0.156 10 true *A 4.677,3.406 4.885,3.563 0.208,0.156 10 true *a 6.323,3.188 6.531,3.344 0.208,0.156 10 true *b 0.333,0.969 0.521,1.146 0.188,0.177 10 true *c 1.26,3.469 1.458,3.625 0.198,0.156 10 true *d 6.229,3.427 6.438,3.583 0.208,0.156 10 true *b 2.781,3.438 2.99,3.594 0.208,0.156 10 true *b 6.229,0.115 6.417,0.292 0.188,0.177 10 true *c 4.365,3.427 4.573,3.583 0.208,0.156 10 true *b
*A w/ Navigation System - -
*a Passenger Airbag Connector *b Connector
*c Clip <A> *d Passenger Airbag Installation Bolt <B>



e.

Place your hands at the position shown in the illustration and pull as shown to detach the clip.


f.

Detach the guide and remove the upper instrument panel sub-assembly.

B409752C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction