Home › Vehicle Interior › INTERIOR PANELS / TRIM › LOWER INSTRUMENT PANEL › from 2016.01
RM3270E _58 Vehicle Interior _041715 INTERIOR PANELS / TRIM _0213629 LOWER INSTRUMENT PANEL A

INTERIOR PANELS / TRIM  LOWER INSTRUMENT PANEL  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for RHD vehicles.



PROCEDURE

Hide 55620 1.REMOVE INSTRUMENT PANEL CUP HOLDER ASSEMBLY (for Driver Side)

a.
B403970

Detach the claw and guide and remove the cover.


b.
B403971C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claw and remove the instrument panel cup holder assembly and instrument panel cup holder tray as shown in the illustration.


Hide 55620 2.REMOVE INSTRUMENT PANEL CUP HOLDER ASSEMBLY (for Passenger Side)

a.
B403974C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claw and remove the instrument panel cup holder assembly and instrument panel cup holder tray as shown in the illustration.


Hide 55618C 3.REMOVE INSTRUMENT PANEL CUP HOLDER (for Driver Side)

a.
B403972C01
1.344,1.771 1.573,1.927 0.229,0.156 10 true *a 2,1.906 2.229,2.063 0.229,0.156 10 true *a 2.875,1.5 3.104,1.656 0.229,0.156 10 true *a
*a Screw <A>


Remove the 3 screws <A>.


b.
B403973C01
2.75,0.469 2.979,0.625 0.229,0.156 10 true *a
*a Clip <E>


Remove the clip <E>.


c.

Detach the clip and guide and remove the instrument panel cup holder.


Hide 55618C 4.REMOVE INSTRUMENT PANEL CUP HOLDER (for Passenger Side)

a.
B403975C01
0.125,1.281 0.344,1.438 0.219,0.156 10 true *a 0.573,1.99 0.792,2.146 0.219,0.156 10 true *a 2.063,1.948 2.281,2.104 0.219,0.156 10 true *a
*a Screw <A>


Remove the 3 screws <A>.


b.
B403976C01
0.646,0.292 0.875,0.448 0.229,0.156 10 true *a
*a Clip <E>


Remove the clip <E>.


c.

Detach the clip and guide and remove the instrument panel cup holder.


Hide 55446A 5.REMOVE NO. 1 SWITCH HOLE BASE

a.
B403977

Detach the claw and remove the No. 1 switch hole base.


Hide 55557A 6.REMOVE GLOVE COMPARTMENT DOOR CHECK CUSHION

HINT:

Use the same procedure for both glove compartment door check cushions.


a.
B403978C01
1.198,1.292 0.917,0.854 true 0.802,0.74 1.031,0.906 0.229,0.167 10 true *a
*a Protective Tape


Using a screwdriver, detach the claw and remove the glove compartment door check cushion.

HINT:

Tape the screwdriver tip before use.



Hide 69056A 7.REMOVE GLOVE COMPARTMENT LOCK CYLINDER ASSEMBLY

NOTICE:

Perform this procedure only when replacement of the glove compartment door assembly is necessary.


a.

Mark the glove compartment door assembly as shown in the illustration.

B478432C01
1.792,1.167 2.083,1.167 true 5.021,1.125 5.313,1.125 true 1.865,0.146 2.021,0.344 0.156,0.198 10 false A 5.135,0.156 5.292,0.354 0.156,0.198 10 false A 0.542,0.146 0.854,0.344 0.313,0.198 10 false *A 3.76,0.146 4.073,0.344 0.313,0.198 10 false *B 1.521,0.313 1.677,0.51 0.156,0.198 10 false B 5.521,0.323 5.677,0.521 0.156,0.198 10 false B 1.135,1.031 1.25,1.208 0.115,0.177 10 true D 1.396,0.635 1.51,0.813 0.115,0.177 10 true C 5.594,0.635 5.708,0.813 0.115,0.177 10 true C 6.042,1.031 6.156,1.208 0.115,0.177 10 true D 4.885,1.031 5.052,1.229 0.167,0.198 10 true *a 2.104,1.073 2.271,1.271 0.167,0.198 10 true *a
*A for LHD *B for RHD
*a Marking - -


Standard Measurement
Area Measurement Area Measurement
A 100.077 mm (3.940 in.) B 50.0 mm (1.969 in.)
C 15.0 mm (0.591 in.) D 45.0 mm (1.772 in.)


b.

Insert a 3.0 mm (0.118 in.) drill bit into a drill.


c.

Tape the 3.0 mm (0.118 in.) drill bit 10.0 mm (0.394 in.) from the tip as shown in the illustration.

NOTICE:

Tape the 3.0 mm (0.118 in.) drill bit to prevent the drill bit from going too deep.



d.

Drill holes along the marking as shown in the illustration.

B475817C01
3.219,0.49 3.354,0.49 3.354,0.49 3.479,0.646 false 5.625,2.333 5.625,2.063 false 5.917,2.333 5.917,2 false 2.667,1.167 2.938,1.396 true 3.219,0.719 3.375,0.917 0.156,0.198 10 false A 3.021,0.406 3.177,0.604 0.156,0.198 10 false *a 5.865,2.344 6.177,2.542 0.313,0.198 10 false *b 5.552,2.344 5.865,2.542 0.313,0.198 10 false *c 2.927,1.292 3.115,1.49 0.188,0.198 10 true *b
*a Tape *b Marking
*c Drilled Hole - -


Standard Measurement
Area Area
A 10.0 mm (0.394 in.)

CAUTION:
·

In order to avoid injury, make sure to work carefully so that the tip of the drill does not slip.

·

Make sure to wear protective glasses when performing this procedure as shavings will fly about.



NOTICE:

To prevent the glove compartment lock cylinder assembly from being damaged, make sure to only drill holes along the marking.



e.

Insert a 7.0 mm (0.276 in.) drill bit into a drill.


f.

Tape the 7.0 mm (0.276 in.) drill bit 10.0 mm (0.394 in.) from the tip as shown in the illustration.

NOTICE:

Tape the 7.0 mm (0.276 in.) drill bit to prevent the drill bit from going too deep.



g.

Redrill each hole using the 7.0 mm (0.276 in.) drill bit.

CAUTION:
·

In order to avoid injury, make sure to center the tip of the drill in the pilot hole so that the tip of the drill does not slip.

·

Make sure to wear protective glasses when performing this procedure as shavings will fly about.




h.

Using a plier nipper (side cutters), cut the glove compartment door assembly between each hole.


i.
B478435C01
0.094,0.188 0.406,0.385 0.313,0.198 10 true *A 0.177,2.667 0.49,2.865 0.313,0.198 10 true *B
*A for LHD
*B for RHD
V113147

Move in this Direction


Move the arm as shown in the illustration.


j.

Press the cylinder lock to release it and pull out the glove compartment lock cylinder assembly from the glove compartment door assembly to remove it as shown in the illustration.

B478437C01
1.271,1.729 1.552,1.729 false 4.646,1.76 4.927,1.76 false 0.271,0.167 0.583,0.365 0.313,0.198 10 false *A 3.656,0.177 3.969,0.375 0.313,0.198 10 false *B 1.594,1.646 1.906,1.844 0.313,0.198 10 false *a 4.958,1.677 5.271,1.875 0.313,0.198 10 false *a
*A for LHD *B for RHD
*a Cylinder Lock - -
V113147

Remove in this Direction - -