Home › Drivetrain › VF2CM TRANSFER / 4WD / AWD › TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM › from 2016.01
RM3270E _52 Drivetrain _041684 VF2CM TRANSFER / 4WD / AWD _0201040 TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM C

VF2CM TRANSFER / 4WD / AWD  TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM  P17A4  Automatic Disconnecting Differential Motor Limit Switch Circuit  


DESCRIPTION

When the A.D.D. actuator switches between 2WD and 4WD, the DL1 and DL2 terminals of the limit switch and ADD terminal of the A.D.D. position switch change to one of the following ON/OFF combinations listed in the table below.

Terminal In 2WD Switching between 2WD and 4WD In 4WD
DL1 ON (GND) ON (GND) OFF (OPEN)
DL2 OFF (OPEN) ON (GND) ON (GND)
ADD OFF (OPEN) OFF (OPEN) ON (GND) ON (GND)

A malfunction is detected depending on the combination of the 3 circuits that make up the limit switch and A.D.D. position switch.

DTC No. Detection Item DTC Detection Condition Trouble Area
P17A4 Automatic Disconnecting Differential Motor Limit Switch Circuit
·

Diagnosis Condition: Directly after the ignition switch is turned to ON, or while switching between H2 and H4 (A.D.D. shift motor operating) with the ignition switch turned to ON

·

Malfunction Status: The ON/OFF combination of DL1, DL2 and ADD does not match the pattern

·

Malfunction Time: 0 seconds

·

Other: 1 trip detection logic


·

Wire harness and connector

·

4 wheel drive control ECU

·

A.D.D. actuator (differential motor actuator assembly)



WIRING DIAGRAM

C325506E09
5.417,0.292 5.729,0.49 0.313,0.198 10 false IG 3.094,0.792 3.406,0.99 0.313,0.198 10 false DL1 3.438,0.792 3.594,0.99 0.156,0.198 10 false 6 3.094,1.26 3.552,1.458 0.458,0.198 10 false DL2 3.438,1.271 3.594,1.469 0.156,0.198 10 false 5 3.031,2.219 3.49,2.417 0.458,0.198 10 false ADD 3.438,2.24 3.594,2.438 0.156,0.198 10 false 3 1.688,2.51 3.26,2.729 1.573,0.219 10 false A.D.D. Position Switch 1.938,1.781 2.76,1.979 0.823,0.198 10 false Limit Switch 1.198,2.198 1.656,2.396 0.458,0.198 10 false GND 1.031,2.219 1.188,2.417 0.156,0.198 10 false 4 0.854,3.135 2.969,3.5 2.115,0.365 10 false A.D.D. Actuator (Differential Motor Actuator Assembly) 0.854,2.917 1.156,3.104 0.302,0.188 10 false C57 4.885,3.021 5.344,3.219 0.458,0.198 10 false C60 4.896,3.198 6.542,3.438 1.646,0.24 10 false 4 Wheel Drive Control ECU 4.958,0.802 5.417,1 0.458,0.198 10 false DL1 4.771,0.813 4.927,1.01 0.156,0.198 10 false 8 4.792,1.271 4.948,1.469 0.156,0.198 10 false 7 4.979,1.281 5.438,1.479 0.458,0.198 10 false DL2 4.969,2.219 5.427,2.417 0.458,0.198 10 false ADD 4.781,2.219 4.938,2.417 0.156,0.198 10 false 2 2.948,4.594 3.406,4.792 0.458,0.198 10 false EXI 2.25,4.042 2.563,4.24 0.313,0.198 10 false IG 3.292,4.688 3.604,4.885 0.313,0.198 10 false A68 3.688,4.688 4,4.885 0.313,0.198 10 false A4 3.74,4.458 3.896,4.656 0.156,0.198 10 false 3 3.323,4.458 3.635,4.656 0.313,0.198 10 false 31 3.344,4.927 3.656,5.125 0.313,0.198 10 false *1 3.708,4.917 4.021,5.115 0.313,0.198 10 false *2 0.948,5.323 3.813,5.531 2.865,0.208 10 false Skid Control ECU (Brake Actuator Assembly) 5.083,4.917 6.771,5.115 1.688,0.198 10 false *1: w/o VSC 5.094,5.198 6.625,5.396 1.531,0.198 10 false *2: w/ VSC

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - DIFFERENTIAL MOTOR ACTUATOR ASSEMBLY)
a.

Disconnect the C60 4 wheel drive control ECU connector.


b.

Disconnect the C57 A.D.D. actuator (differential motor actuator assembly) connector.


c.

w/o VSC:

Disconnect the A68 skid control ECU (brake actuator assembly) connector.

w/ VSC:

Disconnect the A4 skid control ECU (brake actuator assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C60-8 (DL1) - C57-6 (DL1) Always Below 1 Ω
C60-7 (DL2) - C57-5 (DL2) Always Below 1 Ω
C60-2 (ADD) - C57-3 (ADD) Always Below 1 Ω
C57-4 (GND) - Body ground Always Below 1 Ω
C60-8 (DL1) or C57-6 (DL1) - Body ground Always 10 kΩ or higher
C60-7 (DL2) or C57-5 (DL2) - Body ground Always 10 kΩ or higher
C60-2 (ADD) or C57-3 (ADD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK 4 WHEEL DRIVE CONTROL ECU (ECU OUTPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK 4 WHEEL DRIVE CONTROL ECU (ECU OUTPUT VOLTAGE)
a.
A107895C19
1.531,0.688 1.917,0.938 0.385,0.25 2.104,1.385 2.615,1.813 false 1.917,1.427 1.802,1.875 false 1.625,1.417 1.198,1.875 false 1.604,0.719 2.063,0.917 0.458,0.198 10 false C57 0.073,0.094 0.385,0.292 0.313,0.198 10 false *a 2.604,1.865 3.063,2.063 0.458,0.198 10 false DL1 1.677,1.917 2.135,2.115 0.458,0.198 10 false DL2 1,1.896 1.458,2.094 0.458,0.198 10 false ADD
*a Front view of wire harness connector
(to A.D.D. Actuator (Differential Motor Actuator Assembly))


Disconnect the C57 A.D.D. actuator (differential motor actuator assembly) connector.


b.

w/o VSC:

Disconnect the A68 skid control ECU (brake actuator assembly) connector.

w/ VSC:

Disconnect the A4 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C57-6 (DL1) - Body ground Ignition switch ON 10 to 14 V
C57-5 (DL2) - Body ground Ignition switch ON 10 to 14 V
C57-3 (ADD) - Body ground Ignition switch ON 10 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE 4 WHEEL DRIVE CONTROL ECU