Home › Vehicle Interior › LIGHTING (INT) › PERSONAL LIGHT(for LED Type) › from 2016.01
RM3270E _58 Vehicle Interior _041707 LIGHTING (INT) _0245020 PERSONAL LIGHT(for LED Type) G

LIGHTING (INT)  PERSONAL LIGHT(for LED Type)  INSPECTION  


PROCEDURE

Hide 81260A 1.INSPECT MAP LIGHT ASSEMBLY (PERSONAL LIGHT)

a.

Inspect the map light switch.

i.
E320541C01
2,1.01 2.427,0.427 true 1.625,1.01 1.156,0.417 true 0.125,0.104 0.438,0.26 0.313,0.156 10 false *a 1.073,0.25 1.229,0.448 0.156,0.198 10 false B 2.344,0.229 2.802,0.427 0.458,0.198 10 false GND
*a Component without harness connected
(Map Light Assembly (Personal Light))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (B) - 3 (GND) Map light switch LH OFF, RH OFF 10 kΩ or higher
Map light switch LH ON, RH OFF Below 1 Ω
Map light switch LH ON, RH ON Below 1 Ω
Map light switch LH OFF, RH ON Below 1 Ω


If the result is not as specified, replace the map light assembly (personal light).



b.

Inspect the courtesy switch.

i.
E320541C02
2.333,1.01 2.719,0.427 true 1.594,1.01 1.156,0.427 true 0.125,0.104 0.438,0.26 0.313,0.156 10 false *a 1.073,0.25 1.229,0.448 0.156,0.198 10 false B 2.615,0.24 3.073,0.438 0.458,0.198 10 false CTY
*a Component without harness connected
(Map Light Assembly (Personal Light))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (B) - 1 (CTY) Courtesy switch OFF 10 kΩ or higher
Courtesy switch ON Below 1 Ω


If the result is not as specified, replace the map light assembly (personal light).



c.

Inspect the telephone microphone circuit.

i.

Disconnect the telephone microphone assembly connector.


ii.
E324485C01
1.604,0.25 1.885,0.479 0.281,0.229 1.583,2.125 1.865,2.354 0.281,0.229 1.115,3.167 1.365,2.802 true 2.01,3.156 1.802,2.802 true 2.792,2.667 2.458,2.74 true 1.24,1.365 0.635,1.24 true 1.281,1.844 1.479,1.417 true 2.167,1.823 1.656,1.406 true 0.104,0.073 0.417,0.229 0.313,0.156 10 false *a 1.698,0.281 1.875,0.448 0.177,0.167 10 false A 1.677,2.167 1.854,2.333 0.177,0.167 10 false B 0.188,1.135 0.802,1.333 0.615,0.198 10 false MACC 1.083,1.875 1.698,2.073 0.615,0.198 10 false MCO+ 2.115,1.844 2.729,2.042 0.615,0.198 10 false MCO- 1.938,3.188 2.552,3.385 0.615,0.198 10 false MIC+ 2.854,2.573 3.396,2.771 0.542,0.198 10 false MACC 0.958,3.198 1.573,3.396 0.615,0.198 10 false MIC-
*a Component without harness connected
(Map Light Assembly (Personal Light))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A15 (MACC) - B5 (MACC) Always Below 1 Ω
A14 (MCO+) - B3 (MIC+) Always Below 1 Ω
A13 (MCO-) - B2 (MIC-) Always Below 1 Ω


If the result is not as specified, replace the map light assembly (personal light).



d.

Inspect the map light.

i.
E320541C03
2,1.01 2.427,0.427 true 2.708,1.5 2.354,1.313 true 1.635,1.01 1.458,0.427 true 0.125,0.104 0.438,0.26 0.313,0.156 10 false *a 2.76,1.448 3.083,1.646 0.323,0.198 10 false ILL 2.344,0.229 2.802,0.427 0.458,0.198 10 false GND 1.385,0.24 1.844,0.438 0.458,0.198 10 false B
*a Component without harness connected
(Map Light Assembly (Personal Light))


Apply battery voltage to the connector and check the light illumination condition.

OK:
Tester Connection Switch Condition Specified Condition
Battery positive (+) → 5 (B)
Battery negative (-) → 3 (GND)
Map light switch LH ON Map light LH illuminates
Map light switch RH ON Map light RH illuminates
Battery positive (+) → 9 (ILL)
Battery negative (-) → 3 (GND)
Always Switch illuminates


If the result is not as specified, replace the map light assembly (personal light).